Subscribe to Our Youtube Channel
Related Manuals for Hirschmann RSPM20-4Z64Z6 Series
Summary of Contents for Hirschmann RSPM20-4Z64Z6 Series
- Page 1 User Manual Installation Industrial Ethernet Rail Switch Power Media module RSPM Installation RSPM Technical support Release 15 04/2018 https://hirschmann-support.belden.eu.com...
- Page 2 In addition, we refer to the conditions of use specified in the license contract. You can get the latest version of this manual on the Internet at the Hirschmann product site (www.hirschmann.com). Hirschmann Automation and Control GmbH Stuttgarter Str.
-
Page 3: Table Of Contents
Contents Safety instructions About this manual Description General description Device name and product code Media module variants 1.3.1 Port configuration 1.3.2 Media module slots on the RSPE device Ethernet ports 1.4.1 100 Mbit/s F/O port 1.4.2 10/100 Mbit/s twisted pair port 1.4.3 Support of PoE(+) Display elements 1.5.1 Media module status... - Page 4 Scope of delivery Accessories Underlying technical standards Further support Installation RSPM Release 15 04/2018...
-
Page 5: Safety Instructions
Certified usage Use the product only for the application cases described in the Hirschmann product information, including this manual. Operate the product only according to the technical specifications. See “Technical data” on page 29. Connect to the product only components suitable for the requirements of the specific application case. - Page 6 Shielding ground The overall shield of a connected shielded twisted pair cable is connected to the grounding connector on the front panel as a conductor. Beware of possible short circuits when connecting a cable section with conductive shielding braiding. ESD Guidelines ...
- Page 7 ATEX directive 2014/34/EU – specific regulations for safe operation The following applies to RSPM devices if you operate them in areas with explosive gases according to ATEX directive 2014/34/EU: List of standards: EN 60079-0:2012, A11:2013 EN 60079-15:2010 Certificate No.: DEKRA 15ATEX0016X ...
- Page 8 Relevant for use in explosion hazard areas (Hazardous Locations, Class I, Division 2) The relay connections are to be installed and used within their Entity Parameters as per Control Drawing 000182303DNR. Avertissement - Risque d'explosion - Ne pas débrancher tant que le circuit est sous tension à...
- Page 9 For Use in Hazardous Locations Class I Division 2 Groups A, B, C, D: Only allowed for RSPE/RSPM model No´s. which are individually labeled “FOR USE IN HAZARDOUS LOCATIONS”. This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D OR non-hazardous locations only.
- Page 10 Explosive Atmosphere Ordinary Location, Class Division 2 Non-Hazardous Area, Groups A, B, C, D Non-Explosive Atmosphere Hazardous Location RSPE - Industrial Ethernet WARNING! Rail Switch Power Enhanced The USB is for temporary connection only, for maintenance use. Do not use, connect or disconnect unless the area is known to be non-hazardous.
- Page 11 IECEx – Certification Scheme for Explosive Atmospheres For RSPM devices labeled with an IECEx certificate number, the following applies: List of standards: IEC 60079-0:2011+Cor.2012+Cor.2013 IEC 60079-15:2010 The device is suitable for use in an area with a degree of soiling of 2 as per IEC 60664-1.
- Page 12 In accordance with the above-named EU directive(s), the EU conformity declaration will be at the disposal of the relevant authorities at the following address: Hirschmann Automation and Control GmbH Stuttgarter Str. 45-51 72654 Neckartenzlingen www.hirschmann.com The device can be used in the industrial sector.
- Page 13 FCC note: The statements in this chapter refer only to media modules which are correctly mounted in aRSPE basic device (see on page 25 “Mounting a media module”). This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference;...
-
Page 14: About This Manual
Documentation mentioned in the "Installation" user manual that is not supplied with your device in print can be found as PDF download on the Internet at the Hirschmann product pages (www.hirschmann.com). Installation RSPM Release 15 04/2018... -
Page 15: Key
The symbols used in this manual have the following meanings: Listing Work step Subheading Installation RSPM Release 15 04/2018... -
Page 16: Description
Description General description The RSPM media modules are designed for exclusive use in a RSPE basic device. By using media modules, you obtain up to 16 additional Fast Ethernet ports on a RSPE basic device. You will find more information on the media modules in the “User Manual for Installation of RSPE”. -
Page 17: Device Name And Product Code
15 ... 16 Certificates and You will find detailed information on the certificates and declarations declarations applying to your device in a separate overview. See table 2 on page 18. 17 ... 18 Customer-specific Hirschmann Standard version Hardware Standard configuration Software configuration 9 without configuration 21 ... - Page 18 Application case Certificates and Characteristic value declarations Z9 X9 W9 WX WU WD WC WB WA U9 UY UX UW T9 TY V9 VP VU P9 Standard applications ATEX Zone 2 IECEx EN 60950-1 EN 61131-2 ISA-12.12.01 – Class I, Div. 2 UL 61010-1, UL 61010-2-210 UL 60950-1 Substation applications...
-
Page 19: Media Module Variants
Media module variants The media modules have different interface types. The different interfaces of the media modules provide you with the following functions: Specific functions of the TP/TX interface Auto Polarity Exchange Autocrossing (device may be connected with a crossed-over or an un- crossed cable) ... -
Page 20: Media Module Slots On The Rspe Device
1.3.2 Media module slots on the RSPE device Slot 1 for media module RSPM All media modules are pluggable except RSPM20-4Z64Z6... (8 F/O ports) Slot 2 for media module RSPM All media modules are pluggable. Installation RSPM Release 15 04/2018... -
Page 21: Ethernet Ports
Ethernet ports You have the option to connect terminal devices or other segments to the ports of the media modules via twisted-pair cables or F/O cables. Connect the ports of the media modules plugged into the basic device as required in order to set up your industrial Ethernet or expand your existing network. -
Page 22: Support Of Poe(+)
1.4.3 Support of PoE(+) See “Device name and product code” on page 17. The 10/100 Mbit/s twisted pair port allows you to connect network components as a PoE voltage sink according to the standard IEEE 802.3 10BASE-T/100BASE-TX and IEEE 802.3af/at. With the presence of the PoE power supply, a separate power supply for the connected device is unnecessary. -
Page 23: Display Elements
Display elements 1.5.1 Media module status Device variant RSPM20 1 LED is located on the upper part of the media module. This LED provides information on the supply voltage status of the media module. Power Display Color Activity Meaning Power Supply voltage —... -
Page 24: Port Status
1.5.2 Port status These LEDs provide port-related information. The LEDs are directly located on the ports. Display Color Activity Meaning Link status — none Device detects an invalid or missing link green lights up Device detects a valid link flashes 1 time a period Port is switched to stand-by flashes 3 times a period Port is switched off yellow lights up Device detects a non-supported SFP... -
Page 25: Installation
Installation The devices have been developed for practical application in a harsh industrial environment. Hirschmann supplies the media modules ready for operation. To configure a subdomain, follow these steps: Checking the package contents Mounting a media module ... -
Page 26: Installing An Sfp Transceiver (Optional)
Installing an SFP transceiver (optional) Prerequisites: Exclusively use Hirschmann SFP transceivers. See “Accessories” on page 35. Figure 1: Installing SFP transceivers: Installation sequence Proceed as follows: Take the SFP transceiver out of the transport packaging (1). Remove the protection cap from the SFP transceiver (2). -
Page 27: Maintenance And Service
Check regularly whether there is an updated version of the software that provides you with additional benefits. You find information and software downloads on the Hirschmann product pages on the Internet (http://www.hirschmann.com). Note: You find information on settling complaints on the Internet at http:// www.beldensolutions.com/en/Service/Repairs/index.phtml. -
Page 28: Disassembly
Disassembly Removing an SFP transceiver (optional) Figure 2: Removing an SFP transceiver: Removal sequence Proceed as follows: Open the locking mechanism of the SFP transceiver (1). Pull the SFP transceiver out of the slot via the open locking mechanism (2). -
Page 29: Technical Data
Temperature of the ambient air at a distance of 2 in (5 cm) from the device b. Hirschmann recommends to use SFP transceivers with “EEC” extension. c. Note the specifications for the basic device in the “User Manual Installation RSPE”. - Page 30 Dimension drawings inch 101,05 6,64 1.38 3.98 0.26 Figure 3: Dimensions of a media module Installation RSPM Release 15 04/2018...
- Page 31 EMC and immunity You will find detailed information on the certificates and declarations applying to your device in a separate overview. See table 2 on page 18. EMC interference Standard Navy applications Railway Substation emission applications applications applications (trackside) Radiated emission EN 55032 Class A...
- Page 32 EMC interference Standard Navy applications Railway Substation immunity applications applications applications (trackside) IEEE 1613 80 MHz ... 1000 MHz — — — 35 V/m Fast transients (burst) EN 61000-4-4 DC supply connection ±2 kV ±2 kV ±2 kV ±4 kV IEEE C37.90.1 EN 61000-4-4 Data line...
- Page 33 EMC interference Standard Navy applications Railway Substation immunity applications applications applications (trackside) Damped vibration – DC supply connection EN 61000-4-12 line/ground — — — 2.5 kV IEEE C37.90.1 EN 61000-4-12 line/line — — — 1 kV IEEE C37.90.1 Damped oscillation - data line EN 61000-4-12 line/ground —...
- Page 34 Network range Note: The line lengths specified for the transceivers apply for the respective fiber data (fiber attenuation and BLP/dispersion). Product Wave Fiber System Example Fiber BLP/ code length attenuatio for F/O attenuation Dispersion M-FAST- cable SFP-... length -MM/LC... MM 1310 nm 50/125 µm 0 dB ...
-
Page 35: Scope Of Delivery, Order Numbers And Accessories
Power consumption/power output The order numbers correspond to the product codes of the devices. See “Device name and product code” on page 17. Device name Maximum Power output power consumption RSPM20-4Z64Z6... 31 Btu (IT)/h RSPM20-4T14T1... 7 Btu (IT)/h RSPM20-4T14Z6... 17 Btu (IT)/h RSPM22-4T14T1... - Page 36 M-FAST SFP-LH/LC EEC 943 948-001 SFP-FAST-MM/LC 942 194-001 SFP-FAST-MM/LC EEC 942 194-002 SFP-FAST-SM/LC 942 195-001 SFP-FAST-SM/LC EEC 942 195-002 a. You find further information on certifications on the Internet at the Hirschmann product pages (www.hirschmann.com). Installation RSPM Release 15 04/2018...
- Page 37 If your device has a shipping approval according to Germanischer Lloyd, you find the approval mark printed on the device label. You will find out whether your device has other shipping approvals on the Hirschmann website under www.hirschmann.com in the product information.
- Page 38 Further support Technical questions For technical questions, please contact any Hirschmann dealer in your area or Hirschmann directly. You find the addresses of our partners on the Internet at http:// www.hirschmann.com. A list of local telephone numbers and email addresses for technical support...
- Page 39 Installation RSPM Release 15 04/2018...
Need help?
Do you have a question about the RSPM20-4Z64Z6 Series and is the answer not in the manual?
Questions and answers