Page 1
GSM TELEPHONE GSM TELEPHONE SGH-T519 CONTENTS Safety Precautions General Introduction Specification Product Funtion Circuit Description Test Command & Test Procedure Array course control Exploded View and its Parts list MAIN Electrical Parts List 10. Flow Chart of Troubleshooting and Circuit Diagrams 11.
1. Safety Precautions 1-1. Repair Precaution ...1-1 1-2. ESD(Electrostatically Sensitive Devices) Precaution ...1-2 2. General Introduction 3. Specification 3-1. GSM General Specification ...3-1 3-2. GSM TX Power class ...3-2 3-3. EDGE TX Poser Level ...3-3 4. Product Function 4-1. Main Function ...4-1 5.
Page 3
9. MAIM Electrical parts list 10. Flow Chart of Troubleshooting and Circuit Diagrams 10-1. Baseband 10-1-1. Power on ...10-1 10-1-2. Initial ...10-3 10-1-3. Sim Part ...10-4 10-1-4. Charging Part ...10-5 10-1-5. Microphone Part ...10-7 10-1-6. Speaker Part ...10-9 10-1-7. Camera Part ...10-13 10-2.
Page 4
ⓒ This Service Manual is a property of Samsung Electronics Co.,Ltd. Samsung Electronics Co.,Ltd. Any unauthorized use of Manual can be punished under applicable International and/or domestic law. Code No.: GH68-12034A 2006. 08. Rev.1.0...
1. Safety Precautions 1-1. Repair Precaution ● Repair in Shield Box, during detailed tuning. Take specially care of tuning or test, because specipicty of cellular phone is sensitive for surrounding interference(RF noise). ● Be careful to use a kind of magnetic object or tool, because performance of parts is damaged by the influence of manetic force.
Safety Precautions 1-2. ESD(Electrostatically Sensitive Devices) Precaution Several semiconductor may be damaged easilly by static electricity. Such parts are called by ESD(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below. You can prevent from ESD damage by static electricity. ●...
2. General Introduction The SGH-T519 Quad Band phone functions as digital phone working in GSM (Global System for Mobile communications)850,EGSM900, DCS1800 and PCS(PersonalCommunication System)1900 modes. <Specification> ● Dimension : 113 x 50 x 8.6 mm (with Standard Battery) ● Weight : 76g (with Standard Battery) ●...
3. Specification 3-1. GSM General Specification GSM850 F r e q . Ba n d [ M Hz ] 824~849 Uplink/ Downlink 869~894 A RFCN rang e 128~251 T x /Rx s pacing 45 MHz 270.833 Kb ps GP RS Mod.
3-2. GSM TX power class Power Power GSM850 control control level level 33±2 dBm 31±2 dBm 29±2 dBm 27±2 dBm 25±2 dBm 23±2 dBm 21±2 dBm 19±2 dBm 17±2 dBm 15±2 dBm 13±2 dBm 11±2 dBm 9±2 dBm 7±2 dBm 5±2 dBm SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Specification 3-3. EDGE TX Power Level Power Power GSM850 control control level level 27±3 dBm 25±3 dBm 23±3 dBm 21±3 dBm 19±3 dBm 17±3 dBm 15±3 dBm 13±3 dBm 11±5 dBm 9±5 dBm 7±5 dBm 5±5 dBm SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization Power EGSM900...
4. Product Function Main Function -1.3 Megapixel Camera and Camcorder -Bluetooth ® Wireless Technology -Instant Messageing capability -Multimedia capability -Fun & Apps featureprovides My Files, music player, games, alarms, calendar, task list, calculator, world time, unit conversion, timer, and stopwatch. SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
5. Circuit Description < RF Circuit Description of SGH-T519 > 1. FEM (F100) ==> Switching Tx, Rx path for GSM850, EGSM900, DCS1800 and PCS1900 controlled by logic. Integration of GSM850, EGSM900, DCS1800 and PCS1900 RX SAW Filters. To convert Electromagnetic Field Wave to Acoustic Wave and the pass the specific frequency band.
Page 13
Circuit Description - TX Function The device implements Skyworks Polar Loop transmit architecture. This architecture autonomously splits the amplitude and phase within the device using the traditional analog In-Phase and Quadrature (I/Q) signals. The filter-saving advantage of the translation-loop approach is embedded in the architecture. Also included is an AM loop that provides both signal AM and power level control.
Page 14
● Timing and control unit ● RF serial interface ● Low-power sleep mode controller ● Baseband Transmitter / Receiver ● Voice input and output 2. WM8955L(UCD401) ==> The WM8955L is a low power, high quality stereo DAC with intergrated headphone and loudspwaker amplifiers, designed to reduce external component requirements in portable digital audio application.
Page 15
Circuit Description ● Synchronous serial port supporting ● Programmable 48-bit general-purpose IO unit, keyboard interface, programmable interval timer and real-time clock. ● SD/MMC controller that supports interfacing to secure digital/multimedia memory card. Two DSP16000 dual-MAC DSP cores; ● Up to 404 million MACs per second at 101 MHz. ●...
6. Test Command & Test Procedure 6-1. Calibration Equipment - HP 8960 - DC Power Supply - Test Jig - Configuration 6-2. Calibration Program - Samsung internal software SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization HP8960 DC POWER SUPPLY GPIB...
6-3. Tx Power Tune up Procedure - GMSK 1) Procedure: a. Calibraion equipment HP8960 and the cell phone are connected through RF cable. b. Target power ( required power level according to the specification which should be set by calibration program) is set to equipment as power level (ex: GSM 5 level is 32.5 dBm).
Page 18
Test Command & Test Procedure - 8PSK 1) Procedure: a. Calibraion equipment HP8960 and the cell phone are connected through RF cable. b. Target power ( required power level according to the specification which should be set by calibration program) is set to equipment as power level (ex: GSM 8 level is 27 dBm).
Page 19
See the TX power level definition table below. 3) Target values of the peak level of the phone are set normally in conducted mode - GSM850 8 level : 27dBm - EGSM900 8 level : 27dBm - DCS 2 level : 26dBm - PCS 2 level : 26dBm (Tolerance : -2dB ~ +1dB ) 4) Accuracy All the TX level from the phone after tuned-up satisfy the EGPRS...
7. Array course control Test Jig (GH80-03307A) Test Cable (GH39-00478A) RF Test Cable (GH39-00397A) SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Array course control Software Downloading 7-1. Downloading Binary Files • Two binary files for downloading T519. – T 519XXYY.s3 : Main source code binary. 7-2. Pre-requsite for Downloading • Downloader Program(OptiFlash.exe) • T519 Mobile Phone • Data Cable • Binary files SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
7-3. S/W Downloader Program 1. Load the binary download program
by executing the 2. Select the “Options” -> “Settings” -> “Generic” -> “Specify hardware platform”. Choose hardware platform for the downloader file setting. Set the everything else as the default values which are shown below SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization “OptiFlash.exe”...
Page 23
Array course control 3. Select the COM port when the download cable is connected Up to 64 ports are supported. Additionally you can select the maximum transfer speed OptiFlash will use to communicate with the phone. However, OptiFlash will use a slower speed if either the PC’s or the phone’s serial hardware is incapable of handling the selected speed.
Page 24
Array course control 4. Select the“Flash&Verify” -> “Browse” Set the directory path and choose the latest s/w binary, for example “T519XXYY.s3”,
for the downloader binary setting. In case of D407 the reserved regions are not a necessity. (It is defined in platform.def file) SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Page 25
Array course control 5. Click “OK” button then press “Flash”. (Before pressing ‘Flash’ button, push the button ‘*’and ‘END’ at the same time. Then press ‘Flash’.) Downloader will upload the binary file as below for the downloading. 6. When downloading is finished successfully, there is a “All is well” message.
8. Exploded View and its P artslist 8-1. Cellular phone Exploded View QFR01 QVO01 QLC01 QFL06 QVK01 QAN02 QCA01 QME03 QRE01 QCW01 QCR06 QSC01 QSC02 QRF01 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization QSD01 QRF03 QMI03...
Disassembly and Assembly instructions 8-3. Disassembly 1.Unscrew 4 points of a rear. ※ caution 1.Be careful not to do damage and scratch the phone. 1.Remove both side keys,then detach the EL KEY FPCB CONNECTOR. ※ caution 1.Be careful not to cut both si d e keys and damage to came ra connector pi n s 1.Remove a camera and SPK/MOT connector.
Page 30
Disassembly and Assembly instructions 1. Detach a LCD from LCD braket. ※ caution 1.Be careful not to do damage and scratch the phone. SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
8-4. Assembly 1. Attach an EL sheet 2. Attach a key pad A. Remove a adhesive tape of EL sheet. B. Attach a EL sheet C. Attach a mic cover D. Attach a key pad E. Press a key pad - Pressure kgf : 6 ±...
Page 32
Disassembly and Assembly instructions 1. Examnine the surface of 2. Place LCD and sponge CARRIER LOWER CAMERA SPONGE LCD place hole SHORT PREVENTION TAPE Baseline ABSORBER Attach keeping away from completion soldering part. A.Place a LCD inserting LCD connector on the front of CARRIER LOWER. B.Place a LCD into place hole of CARRIER LOWER correctly.
Page 33
1. Place a PBA A. Press carefully the top of PBA with your right hand grasping CARRIER LOWER with your left hand. B. Press both sides of PBA until it clicks into the CARRIER LOWER. (Grasp the edge of LCD during work) C.
Page 34
Disassembly and Assembly instructions 1. Solder the intenna 2. Place the camera A. Solder the intenna with soldering jig B. Place the camera into a groove of CARRIER LOWER. C. Press carefully after placing camera module. 1.Place the PBA side keys A.
Page 35
1. Remove the protection film inside CAMERA WINDOW 2. Place the REAR Locker No.1 Locker No.2 A. Place the top of a REAR and press down until it clicks into the Front B.Press the Locker No.1 and Locker No.2 C.SCREW.(4 POINT) SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization Disassembly and Assembly instructions...
10. Flow Chart of Troubleshooting 10-1.Baseband 10-1-1. Power ON 'Power ON' Does not work Check the current consumption Current consumption ≥ 100mA ? Check the V bat. voltage Voltage ≥ 3.3V ? Check the pins of UCD301 C316 ≥ 1.8V ? C318 and C315 = 2.8V? Check the clock signal at pin #3 of TCX101 or C129...
Page 49
Flow Chart of Troubleshooting 10-3 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Flow Chart of Troubleshooting 10-1-2. Initial Initial Failure The voltage at the C316=1.8V? The voltage at the C315=2.8V? The voltage at the C216 " Low --> High" ? There is 32.768KHz wave form at the C222, C223 ? The voltage is 2.8V at the C317,C313,C315,C318 ? LCD Display OK ? Sound operation OK ?
Flow Chart of Troubleshooting 10-1-3. Sim Part "Insert SIM" is displayed on the LCD The voltage is 2.8V at C306? Check the UCD301 Is there any signal Check the UCD301 & UCP201 pin C305, C308, C309? Check the SIM Card 10-6 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Page 53
VSIM SIM_RST SIM_CLK C306 C307 C308 C309 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization Flow Chart of Troubleshooting ZD302 SIM301 12 12 C305 11 11 10 10 10-7 SIM_IO...
Flow Chart of Troubleshooting 10-1-4. LCD Display part LCD display is abnormal Check LCD connection and replace LCD LCD Backlight is on? C338, C340 is 2.9V? pin#4 of ZD304 is LOW? Are there anysignal at pin#6 of ZD304? IS there any problem at F301, F302, F303, F304 Check U400...
10-1-5. Microphone Part Micro-phone does not work Is the connection status of HDC300 O.K? Check the DC bias voltage on Mic path. The voltage of C406 is about 2.2V±10%? Is microphone OK? SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization Flow Chart of Troubleshooting ①...
Page 58
Flow Chart of Troubleshooting EL_PWR EL_PWR KEY_COL(0) KEY_COL(1) KEY_COL(2) KEY_COL(3) KEY_COL(4) MIC+ C311 V306 V307 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization HDC300 18 18 14 14 13 13 12 12 10 10 V311 V309 V310...
10-1-6. Speaker Part There is no sound from speaker Is the connector HDC401 O.K? Are there any signal at L405, L406? Are there any signal at R437, R438? Are there any signal at the pin #15, 16 of UCD401? Are there any signal at the pin #5,6,7 of UCD401? Check UCP201 The frequency at R433...
Page 60
Flow Chart of Troubleshooting 13M_BUF VCCD_1.8V_EN VBAT 2 AVIN R314 MODE/SYNC 4 NC C365 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization VRF_2.9V U101 1 NC VCC 6 NC 5 R124 3 GND C137 R126 VCCD_1.8V...
Page 61
Flow Chart of Troubleshooting 10-15 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Flow Chart of Troubleshooting 10-1-7. Receiver Part There is no sound from receiver. Is the connection of HDC401 OK? Are there any signal at L407, L408 ? Change receiver module SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization Replace the Connection or change receiver module Are there any signal...
Page 63
Flow Chart of Troubleshooting 10-17 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Flow Chart of Troubleshooting 10-1-8. Camera part Camera function does not work Is the connect HDC301 ok? C452 IS HIGH? Pin #3 of Q400 = 1.5V? Pin #3 of Q403 = 2.8V? Pin#3 of OSC401 is 24MHz? Is that clock signal at the pin #23 of HDC301? Pin#24 of HDC301 is High? SAMSUNG Proprietary-Contents may change without notice...
Page 65
VCAMIO_2.8V CAM_D(0) CAM_D(1) CAM_D(2) CAM_D(3) CAM_D(4) CAM_D(5) CAM_D(6) CAM_D(7) MCLK SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization Flow Chart of Troubleshooting VCAM_1.5V VCAMA_2.8V HDC301 11 11 12 12 15 15 16 16 19 19 20 20 23 23...
Page 66
Flow Chart of Troubleshooting 10-20 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
10-1-9. Mp3 part There is no MP3 sound from Earphone Are there any signal at the pin #5,7 of IFC400? Are there any signal at R410, R411? Are there any signal at the pin #10,13 of UCD401? Are there any signal at the C407, 417? Are there any signal at the PIN #5,6,7?
Page 68
Flow Chart of Troubleshooting 10-22 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Page 69
Flow Chart of Troubleshooting 10-23 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Page 70
Flow Chart of Troubleshooting 10-24 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Page 72
Flow Chart of Troubleshooting 10-26 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Page 76
Flow Chart of Troubleshooting 10-2-5. GSM850 / GSM900 TX F100 Pin#17 About 2~3 dBm? RFS101, C100 Check / Change ② Check & Change C108 = 3.7V? Level of PAM101 Pin #6 is 1.2V? PAM101 pin#12 About -5 dBm? PAM101 pin#1 High ? ⑤...
Page 77
Flow Chart of Troubleshooting 10-31 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
Page 78
Flow Chart of Troubleshooting 10-2-6. DCS1800 & PCS1900 TX F100 Pin#17 About 2~3 dBm? RFS101, C100 Check / Change ② Check & Change C108 = 3.7V? Level of PAM101 Pin #6 is 1.2V? PAM101 pin#12 About -5 dBm? PAM101 pin#1 High ? ⑤...
Page 79
Flow Chart of Troubleshooting 10-33 SAMSUNG Proprietary-Contents may change without notice This Document can not be used without Samsung's authorization...
13. Reference data 13-1. Reference Abbreviate AAC: Advanced Audio Coding. AVC : Advanced Video Coding. BER : Bit Error Rate BPSK: Binary Phase Shift Keying CA : Conditional Access CDM : Code Division Multiplexing C/I : Carrier to Interference DMB : Digital Multimedia Broadcasting EN : European Standard ES : Elementary Stream ETSI: European Telecommunications Standards Institute...