Subscribe to Our Youtube Channel
Related Manuals for Federal Signal Corporation 191XL Series
Summary of Contents for Federal Signal Corporation 191XL Series
- Page 1 Model 191XL Series Beacon for Use in Hazardous Conditions Installation and Maintenance Manual 2561421G rançais....page 21 REV. G 513 español....página 41 Printed in U.S.A.
- Page 2 Warranty – Seller warrants all goods for five years on parts and 2-1/2 years on labor, under the following conditions and exceptions: Seller warrants that all goods of Seller's manufacture will conform to any descriptions thereof for specifications which are expressly made a part of this sales contract and at the time of sale by Seller such goods shall be commercially free from defects in material or workmanship.
-
Page 3: Table Of Contents
Contents Safety Messages to Installers ............5 An Overview of the 191XL Series ............. 6 Unpacking the Beacon ..............7 Pipe-Mounting the Beacon (191XL) ..........8 Surface-Mounting the Beacon (191XL-S) ........10 Wiring the Beacon ................11 Wiring 120-240 Vac, 277 Vac Models ........12 Wiring 24 Vac/dc Models ............ - Page 4 Contents Figures Figure 1 Pipe-mounted beacon ............9 Figure 2 Surface-mounted beacon ..........10 Figure 3 PCB removed from housing ..........15 Figure 4 Location of jumper J3 on PCB ........... 16 Model 191XL Series LED Beacon...
-
Page 5: Safety Messages To Installers
• To be an effective warning device, this product produces bright beacon that can be hazardous to your eyesight when viewed at a close range. Do not stare directly into this lighting product at a close range or permanent damage to your eyesight may occur. Model 191XL Series LED Beacon... -
Page 6: An Overview Of The 191Xl Series
Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death. An Overview of the 191XL Series This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D; Class II, Division 1, Groups E, F & G; Class III OR non-hazardous locations only. -
Page 7: Unpacking The Beacon
Ambient Storage Rating: –55 °C to +70 °C Ambient Operating Rating: –50 °C to +66 °C Type 4X (water-tight and corrosion resistant) and indoor/outdoor use IP66 (dust-tight and protection against heavy seas) and outside type (saltwater) Model 191XL Series LED Beacon... -
Page 8: Pipe-Mounting The Beacon (191Xl)
To prevent the ingress of water and dust, apply conductive sealant to the conduit threads prior to mounting. If non- conductive sealant is used, the enclosure must be earthed via the provided internal grounding wire/grounding screw to ensure proper grounding continuity. Model 191XL Series LED Beacon... -
Page 9: Figure 1 Pipe-Mounted Beacon
MINIMUM torque of 5 ft-lb (6.8 N·m) after threading it onto the pipe. Thread the fixture onto the 3/4" pipe and secure it with the set screw. Figure 1 Pipe-mounted beacon 191XL LIGHT ASSEMBLY 3/4" NPT PIPE 290A6881 Model 191XL Series LED Beacon... -
Page 10: Surface-Mounting The Beacon (191Xl-S)
Drill a 9/32 inch (7.143 mm) hole at each mark. Secure the beacon to the mounting surface with installer supplied hardware. Figure 2 Surface-mounted beacon 191XL-S LIGHT ASSEMBLY INSTALLER-SUPPLIED MOUNTING HARDWARE DRILL TWO 9/32" (7.143 mm) HOLES MOUNTING SURFACE 290A6880 Model 191XL Series LED Beacon... -
Page 11: Wiring The Beacon
Wiring must comply with the National Electrical Code or Canadian Electrical Code and the local authority having jurisdiction. The Model 191XL Series LED Beacon should be installed per the NEC or CEC, STATE and LOCAL CODES. Alternate installation locations and/or orientations should only be performed with the approval of the authority having jurisdiction. -
Page 12: Wiring 120-240 Vac, 277 Vac Models
• Any maintenance to the light system must be performed by a trained electrician who is thoroughly familiar with all applicable national and local codes in the country of use. • Do not connect this beacon to the system when power is on. Model 191XL Series LED Beacon... -
Page 13: Changing From Flash Mode To Steady Mode
Lubricated threaded joints exposed for long periods of time may attract small particles of dirt or other foreign materials. Housing and cover joints should be reassembled immediately, with all the threads fully engaged. Model 191XL Series LED Beacon... - Page 14 Thread the dome assembly back onto the housing by turning it clockwise to tighten. SHOCK HAZARD—To avoid electrical shock hazards, do not connect wires while power is applied. Reconnect the beacon to power. Model 191XL Series LED Beacon...
-
Page 15: Figure 3 Pcb Removed From Housing
10. Test the device by applying power and verifying the steady operation of the LED lamp. Figure 3 PCB removed from housing DOME ASSEMBLY NYLON SCREW BUSHING #8-32 PAN-HEAD SCREW LED EMITTER PRINTED CIRCUIT BOARD ASSEMBLY INSULATING PADS CAST HOUSING 290A7308 Model 191XL Series LED Beacon... -
Page 16: Cleaning The Fixture
The fixture should be cleaned periodically to maintain maximum light output. Only mild, non-abrasive cleaning agents should be used. The glass dome should be regularly inspected for scratches and chips, and if damaged, MUST be replaced. Model 191XL Series LED Beacon... -
Page 17: Lubricating The Threaded Joint
K8449078-07 Dome Assy., Red K8449078 Gasket K8449080 Grease, 8 oz Tube KR81-05-01 Dome Guard K8449090 LED Emitter, Amber K14700030-A LED Emitter, Blue K14700030-B LED Emitter, Green K14700030-G LED Emitter, Red K14700030-R LED Emitter, White K14700030-W Model 191XL Series LED Beacon... -
Page 18: Getting Repair Service And Technical Assistance
Defective products that are returned within the warranty period will be repaired or replaced at Federal Signal’s sole discretion. Defective products do not include those products with lamp failure. Circumstances other than those listed above will be addressed on a case-by-case basis. Model 191XL Series LED Beacon... - Page 19 © 2013 Federal Signal Corporation. All rights reserved.
- Page 20 Federal Signal Corporation Industrial Products 2645 Federal Signal Drive University Park, IL 60484-3167 Phone: +1 877 289 3246 • +1 708-534-4756 • Fax: +1 708 534 4887 www.federalsignal-indust.com • www.fs-isys.com...
Need help?
Do you have a question about the 191XL Series and is the answer not in the manual?
Questions and answers