Insert strip of staples into rear of Inserte la tira de grapas en magazine. Use only genuine SENCO la parte de atrás del área de fasteners. Do not load with safety almacenamiento. Use solamente element or trigger depressed.
PW200 Pull feeder shoe back into “locked” position. Lay strip of staples onto rail. Use only genuine SENCO fasteners. Do not load with safety element or trigger depressed. Tap feeder shoe and allow to slide forward. PW150/PW150R/PW200/...
Insert strip of staples into rear of Inserte la tira de grapas en magazine. Use only genuine SENCO la parte de atrás del área de fasteners. Do not load with safety almacenamiento. Use solamente element or trigger depressed. Pull sujetadores SENCO auténticos.
Page 5
Tool Use English This tool is equipped with a depth SNS40/41/44XP/45XP/50/ control safety element. To adjust SQS55 the depth of the staple being driven, loosen the screw and slide the lower safety element up or down and lock in place by tightening the screw. Be sure the safety element moves freely after adjustment.
Page 6
SNS40/41/44XP/45XP/50/SQS55/ PW150/PW150R/PW200 SC2/MW SNS40/41/44XP/45XP/50/SQS55/ PW150/PW150R/PW200 SC2/MW/PW Uso de la Herramienta Tool Use English Espanol Oprima ambos lados del alimen- Depress feeder clip ends on both tador y deslícelo hacia adelante. sides of feeder shoe and slide for- Remueva las grapas. ward over the staple strip.
Page 7
Pull latch and slide magazine rail open. Remove jammed fastener. Connect air supply and replace fasteners. Connect air supply and replace fasteners. Pull feeder shoe back. SNS40/41/44XP/45XP/50/SQS55/ Connect air supply and replace PW150/PW150R/PW200 fasteners. Tap feeder shoe and See also SPS-04a.art allow to slide forward.
No use trigger sticks or binds. la herramienta si el seguro o el gatillo se atoran. Squirt Senco pneumatic oil (5 to 10 Aplique aceite neumático Senco drops) into the air inlet twice daily.
Parts Kit B. SNS41/44XP/45XP/50/ SYMPTOM SQS55 Other problems. SOLUTION Contact SENCO. SC1/SC2/L/MW/PW Accessories SENCO offers a full line of accessories for your SENCO tools, including: Air Compressors Hose Couplers Fittings Safety Glasses Pressure Gauges Lubricants ...
SPS/PW/MW PW150/PW150R PW200 SNS40/41/44XP/45XP SNS50/M2 Specifications Especificaciones Espanol English Code inches Specifications Especificaciones Espanol English Code inches ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ *SOFTWOOD APPLICATIONS ONLY *SOLO PARA APLICAIONES EN MADERA BLANDA *UNIQUEMENT DANS DU BOIS TENDRE Specifications Especificaciones Espanol...
Page 12
English TECHNICAL SPECIFICATIONS Minimum to maximum operating pressure 70–120 psi Air Consumption (60 cycles per minute) 2.16 scfm Air Inlet in. NPT Maximum Speed (cycles per second) Weight 5.3 lbs. Staple Capacity Tool size: Height Tool size: Length Tool size: Width: Main Body Tool size: Width: Rear Bracket 80–120 psi Minimum to maximum operating pressure...
Options English RESTRICTIVE TRIGGER—This feature is helpful when precise fastener placement is required. 3/4" Guide Body Assy.—This as- sembly can be used to allow any SPS model to drive short length FA0155 fasteners only, from 1/2" to 3/4" (P08–P11).
Page 16
TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE. Replacement of Tool Due to Natural Disaster Senco will also replace any tool destroyed by an Act of God such as flood, earthquake, hurricane or other disaster resulting only from the forces of na- ture.
Need help?
Do you have a question about the M2 and is the answer not in the manual?
Questions and answers