Subscribe to Our Youtube Channel
Related Manuals for Senco FramePro 702XP
Summary of Contents for Senco FramePro 702XP
- Page 1 �������� ������������ �������� � ��������� � � �������� � ���������� ��������������� ��������������� ������������������������������������ ������������� ��������������������������������� �����������������...
-
Page 2: Table Of Contents
Espanol English TABLA DE MATERIAS TABLE OF CONTENTS Uso de la Tool Use Herramienta Maintenance Mantenimiento Troubleshooting Identificación de Fal- Specifications Options Especificaciones Accessories Opciones Accesorios RESPONSABILIDADES DEL EMPLOYER’S EMPLEADOR RESPONSIBILITIES El empleador debe hacer Employer must enforce cumplir las advertencias de compliance with the seguridad y todas las otras safety warnings and... - Page 3 GC0547 FramePro To Load: Insert strip of nails into rear of magazine. Use only genuine SENCO fasteners. Do not load with safety element or trigger depressed. Pull feeder shoe back. With a Contact Acuation trigger, nails can be driven two ways:...
- Page 4 SN60MC FramePro ® Uso de la Herramienta Utilisation de l’Outil Tool Use Espanol English Esta herramienta esta equipada This tool is equipped with a con un mecanismo de seguridad movable rail safety mechanism. de riel movible: To activate the tool: 1.) Antes de cada disparo, ase- 1.) Before each firing, be sure to gurese de que el primer clavo...
- Page 5 Tool Use English SN70 Release E-Z Clear latch and open door. Remove jammed fastener. Close door and latch. Loosen locking knob at the rear of the tool by hand. Pull magazine back. Clear jammed fastener from guide body.
- Page 6 FramePro ® SN60MC FramePro ® Tool Use Uso de la Herramienta Utilisation de l’Outil Espanol English La Herramienta puede ser The tool can be converted for convertida para aplicaciones de non-toenail (flat surface) appli- clavado no inclinado, agregando cations by adding the no-mar el cojinete no–mar.
-
Page 7: Maintenance
Aplique aceite neumático Squirt Senco pneumatic oil (5 to SENCO en la entrada de aire 10 drops) into the air inlet twice dos veces al día (dependiendo... - Page 8 Notes...
-
Page 9: Identificación De Fal Las
être réalisées llevadas a cabo solamente por uniquement par du personnel personal entrenado y calificado. qualifié ayant reçu la formation Póngase en contacto con SENCO appropriée. Pour toute information, prenez contact avec SENCO para información 1-800-543-4596. par téléphone en appelant Le Distributeur agréé. -
Page 10: Specifications
SN70 .106" 2,7 mm 2,9 mm Specifications Especificaciones English Code inches JF25 GE21 GE24 ⁄ GC21 GC23 ⁄ GC24 ⁄ GC25 ⁄ HC27 KC27 KC28 ⁄ KC29 ⁄ HF27 .113" .113" 2,9 mm .120" 3 mm Specifications Espanol Francais .106" 2,7 mm .113"... -
Page 11: Especificaciones
FramePro 602/652 ® & 702XP/752XP FRH Code GL** Series GD** * Rounded to nearest 5 mm ** FramePro 602/702XP only .113" .113" 2,9 mm 2,9 mm Specifications Especificaciones English FramePro FRH inches ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄... - Page 12 FramePro 601/651 ® & 701XP/751XP CH Series .113" 2,9 mm 2,9 mm Specifications Especificaciones English Code inches ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ ⁄ .113" .120" .120" 3,1 mm 3,1 mm Specifications Espanol Francais .113" 2,9 mm .120" 3,1 mm .131"...
- Page 13 Specifications SN60MC Specifications TECHNICAL SPECIFICATIONS SN70 65–120 psi Minimum to maximum operating pressure Air Consumption (60 cycles per minute) 9.67 scfm Air Inlet ⁄ in. NPT Weight 9.7 lbs. Fastener Capacity 50-70 Tool size: Height 14.7 in. Tool size: Length 15.9 in.
-
Page 14: Opciones
TECHNICAL SPECIFICATIONS Minimum to maximum operating pressure Air Consumption (60 cycles per minute) Air Inlet Weight Fastener Capacity Tool size: Height Tool size: Length Tool size: Width: Main Body ESPECIFICACIONES TECNICAS Presión de operación mínima y máxima Consumo de aire (60 ciclos por minuto) Entrada de aire Peso Capacidad de grapas por cargador... -
Page 15: Accessories
The case can also be used to carry accessories and fasteners. Accessories English SENCO offers a full line of ac- cessories for your SENCO tools, including: Air Compressors Hose Couplers ... -
Page 16: General Warranty Conditions
601/651 & 602 FRH & SN60MC & SN70] from date of purchase by the original retail purchaser. During this period, Senco Products, Inc., will repair or replace at Senco’s option, any original part or parts for the original retail purchaser. This will be done free of charge, provided the parts are determined defective in materials or workmanship upon examination by a Senco Authorized Warranty Service Center (exception: rubber o-rings and seals, driver blades).
Need help?
Do you have a question about the FramePro 702XP and is the answer not in the manual?
Questions and answers