Page 1
Satellite Installation Manual SEGA AMUSEMENTS USA INC.
Page 2
SECURING THE SATELLITE PLACEMENT POSITIONS Be sure that all adjusters are placed against the floor. Failure to place the adjusters against the floor could lead to accidents caused by cabinet movement. Each satellite is equipped with 4 adjusters and 4 casters. When the placement position has been determined, place the adjusters directly against the floor and perform adjustments to make the satellite horizontally level.
Page 3
Place all the adjusters against the floor. Use a wrench to adjust the height of the adjusters so that the satellite is horizontally level. Following adjustment, tighten the nut on each adjuster to fix the height. Be sure to make contact with the surface. Replace the 4 covers at the corners.
Page 4
POWER SUPPLY, AND EARTH CONNECTION ● Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage WARNING! Breaker can cause a fire when electric leakage occurs. ●...
Page 5
Ensure that the main switch is OFF. CIRCUIT PROTECTOR Main SW off AC Cable (Power Cord) FIG. 6. 3 b AC UNIT OF THE MAIN PROJECTION UNIT AC COVER POWER SW OFF. CIRCUIT PROTECTOR(5A) POWER SWITCH FIG. 6. 3 c AC UNIT OF THE SATELLITE Firmly insert the power plug into the socket outlet.
Page 6
One end of the earth wire should be connected to the product's earth terminal, and the other end to an indoor earth terminal. The earth terminal of the AC unit consists of a bolt and nut set. First remove the nut, then place the end of the earth wire so that the bolt passes through, and finally tighten the nut.
COMMUNICATION CONNECTIONS The communication cables are fiber optic type cables, and should be handled STOP carefully. Improper handling may result in damage (such as from folding) that would render them unusable. IMPORTANT! Do not place heavy objects on the cables or step on them. ...
Page 8
Open the cover of the satellite AC unit. Remove the fiber guide plate by removing the 2 screws. Run the two communication cables through the Satellite. PHOTO 6. 4 c Connect the communication cables to the RX and TX connectors at the Naomi shield case inside the satellite.
Page 9
Use the cord clamp inside the satellite to secure the communication cables (Photo 6. 4 e). Near the cable exit, make loops in the communication cables with a diameter of at least 6 cm. Use the repeat tie belt to secure the looped communication cables (Figure 6.
Page 10
DIAGRAM EXPLAINING COMMUNICATION CABLE CONNECTIONS The diagram below illustrates an example of communication cable usage. Communication cables of appropriate lengths should be used in accordance with satellite layout. www.seuservice.com...
Page 11
SETTING THE CARDS STOP ● Please be sure to use the proprietary cards for this product. Usage of other cards could cause malfunctioning or breakdown. ● Be sure to set the cards in accordance with the specified procedure, direction, IMPORTANT! and number.
Page 12
Place the cards in the dispenser in accordance with the instructions on the sticker that appears on the dispenser. Be careful not to place the cards backwards or upside down. The number of cards that can be placed in the dispenser at any one time is 100. In order to avoid problems such as jamming, be sure not exceed this limit.
Main Board Settings 1. Press the test button on the Satellite to enter the main test mode. 2. Move cursor to Game test Mode. Press the test button to enter the Game Test. 3. Move the cursor to Game Assignments. Press Test Button to enter. 4.
Page 14
DOC Satellite Pedestal Assy � � Item Part Number 601-11202 601-11112 105-5464 105-5466 105-5465 000-T00630-0C � � Description Carpet 1155x11545 Gray SHE-M003 Seat Stopper DOC-M007 for SHE Corner Edge L1249 SCR Type DOC Corner Edge SCR Type DOC Corner Edge L859 SCR Type DOC M SCR TH CRM M6x30 �...
Need help?
Do you have a question about the Satellite TV System and is the answer not in the manual?
Questions and answers