SECO-LARM ENFORCER Voltage Converter ST-LA105-TTQ Installation Manual

Installation Manual
ENFORCER
ST-LA105-TTQ
ST-LA1 10-TTQ
Voltage Converters

Introduction:

The ENFORCER Voltage Converter is a low voltage step-down voltage converter. It converts low voltage AC or
DC to one of three different regulated DC outputs. It is useful for CCTV DC cameras, access controls, as well
as many other applications where low DC voltage is required.

Features:

• Selectable 5, 12, or 24 VDC output via jumper.
• Built-in overload protection.
• Regulated and filtered output.
• Output current protection:
– 0.5 Amp for ST-LA105-TTQ
– 1.0 Amp for ST-LA110-TTQ

Installations:

1. Remove the cover by simultaneously pressing the
2 indented slots located on the side of the cover.
2. Set the desired output voltage to 5, 12, or 24 VDC.
See table 3. The factory default output setting is
12 VDC.
3. Connect the output wires from the power supply to the
power input terminal blocks. See specification chart
for the power requirements. Turn on the power of the
power supply.
4. Use table 2 to check the LED status for the input
and output voltage.
5. To avoid potential damage, use a voltage meter
to check if the voltage reading at the input and
output terminal blocks is correct.
Observe correct polarity.
Note: 1. Use between 16 AWG and 26 AWG wire
for the input and output terminal blocks.
2. Use the included SECO-LARM DC pigtail
connector for easy installation.
6. Connect device to the power output terminal blocks.
7. If the output voltage is low, then turn the rotary
knob clockwise to increase the voltage or counter-
clockwise to decrease the voltage.
Note: If the output voltage set by the jumper is
higher than the input voltage, then the output voltage
reading will be the same as that of the input voltage.
8. Replace the plastic cover on the voltage converter
and secure it in the desired location.
®
• Adjustable voltage output to compensate
for voltage drop.
• Dual-color LED power output indicator:
– Red indicates 5/12 VDC output.
– Blue indicates 24 VDC output.
• Green power input LED indicator.

Specifications:

Output voltage:
Input voltage:
Output current:
LED indicators:
Current protection:
Connector:
Overload protection:
Size:
Table 1: Adjustable
Output voltage

Table 2: LED indicator chart

LED colors

Table 3: Output voltage selection chart

Output
Voltage
5 VDC
12 VDC
24 VDC
5/12/24 VDC (pre-set 12 VDC), selectable by jumper
8~30 VDC/VAC for 5 VDC
15~30 VDC/VAC for 12 VDC
24~30 VDC/VAC for 24 VDC
ST-LA105-TTQ:
ST-LA110-TTQ:
Power input LED (green)
Power output LED (red for 5 or 12 VDC, blue for 24 VDC)
PTC (Positive Temperature Coefficient)
(500mA for ST-LA105-TTQ, 1A for ST-LA110-TTQ)
" x 1
1 1 /
2
voltage
Adjustable voltage range
5 VDC 4.5 ~
12 VDC 12.2 ~ 13.5 VDC
24 VDC 23.0 ~ 25.2 VDC
Indications
Green Input power is connected.
Output voltage is 5 or 12 VDC.
Red
Output voltage is 24 VDC.
Blue
Jumper Setting
A B C D
500mA@5/12/24 VDC
500mA@24 VDC
1A@5/12 VDC
Terminal blocks
Built-in
(46 x 50 x 23.5 mm)
" x "
31 / 29 /
32 32
output chart
5.6 VDC