Table of Contents
Advertisement
Quick Links
WaterWorks TM
Undersink Reverse Osmosis
HOME DRINKING WATER SYSTEM
Model RO 2000
Installation
Operation
Maintenance
Repair Parts
IF YOU HAVE QUESTIONS
WHEN
INSTALLING,
OPERATING
AND MAINTAINING
YOUR
REVERSE
OSMOSIS
SYSTEM...
CALL TOLL FREE
1-800-86
WATER
System Tested and Certified
to
ANSI/NSF
Standard
58. See
performance
data sheet for details,
Manufactured
by EcoWater Systems, Inc,
PO BOX 64420,
ST. PAUL, MN 55164
Part No. 721 4105
(10/99)
Advertisement
Table of Contents
Related Manuals for Sears WaterWorks RO 2000
Summary of Contents for Sears WaterWorks RO 2000
- Page 1 Undersink Reverse Osmosis HOME DRINKING WATER SYSTEM Installation Operation IF YOU HAVE QUESTIONS INSTALLING, OPERATING AND MAINTAINING YOUR OSMOSIS SYSTEM... CALL TOLL FREE 1-800-86 WATER Manufactured by EcoWater Systems, Inc, WaterWorks TM Model RO 2000 Maintenance WHEN REVERSE performance PO BOX 64420, ST.
-
Page 2: Warranty
WaterWorks trade prac- warranty with all chandise is installed, Sears during installa- within one year, Sears will, upon notice from you, cause such faults to be corrected Damage, cost to you. - SAFETY GUIDES - rules carefully Drinking DO NOT ATTEMPT... -
Page 3: Safety Guides
(pH, hardness, SUPPLY, Foods will look better eliminates the need to buy data sheet is included, from Sears. The data sheet lists what this will remove (or reduce) from the water. MONITOR model has 2 water quality box. Indicator... - Page 4 • WATER SUPPLY -- The cold water supply to your Home Drinking Water System must be within certain chemical limits (see page 17). If not, it will not make product water as it should, and life of the RO membrane is shortened.
- Page 5 - THINGS TO CHECK BEFORE YOU START TO INSTALL - REMOTE LOCATION You can install assembly or water supply saddle valve in another place away from the RO faucet 2O). - TOOLS AND MATERIALS YOU WILL NEED - ==9/16" open end, or adjustable •...
-
Page 6: Water System
DO NOT TURN ON THE WATER SUPPLY TIME. NOTE: BE SURE THE VALVE HANDLE NUT IS TIGHT. each screw evenly, INSTALL THE DRAIN ADAPTER onto the s(nk tail- (FIG. 7, WATER SYSTEM - SADDLE VALVE (FIG. 2) WATER SUPPLY SADDLE In Massachusetts,... - Page 7 (FIG. •.. drill a hole (1-1/4" next to the sink. to 1-1/4" 2. Drill the mounting 3. Place plumbers in the sink top. to prevent SINK WATER SYSTEM - drain adapter ferrule drain tubing connector FAUCET AND INSTALL REPAIR, CONSULT...
- Page 8 Route the and "1/4" bottom, upward the 3/8"tub- adaptor WATER SYSTEM - FAUCET AND BASE ASSEMBLED button (use in step 10) faucet suppod screw (2) (2)_,._ mounting hole TOP VIEW screw (2)
-
Page 9: Tubing Connections
- HOW TO INSTALL YOUR HOME DRINKING WATER SYSTEM - tighten the nut. NOTE: Cut tubing as needed for neat appearance, but keep long enough to alllow easy service of the RO system. 7. If needed, cut the 1/4" tubing (marked BARB ON FAUCET") -
Page 10: Pressure Testing
D. In about 3/8" tubing, 27" long (cut to length needed) 1/4" tubing (WATER SUPPLY) COLD WATER posffilter ASSEMBLY WATER SYSTEM - TUBING TO WATER SUPPLY insert, ferrule and nut, at the water the remaining "WATER SUPPLY"). Tighten... - Page 11 4 hours), open the system faucet is empty. 2. Allow the bladder then open the faucet and empty. After 4 purgings, the system is ready to make product water for your use, WATER SYSTEM WORKS - box. automati shutoff a replaceable tank...
- Page 12 - HOW YOUR HOME DRINKING WATER SYSTEM WORKS - POSTFILTER - continued water. High quality drinking water flows from the postfilter and to the faucet. NOTE: Before going to the faucet, passes through the electronic TDS is measured by a sensor.
-
Page 13: Prefilter Cartridge
6. Be sure the cap o-ring has lubrication (silicone grease). clamp sections and retainers, 7. Replace the electronic box batteries.., WATER SYSTEM - - Always replace the postfilter at the REPLACE POSTFILTER BE SURE TO RELIEVE PRESSURE, 1, 2 AND 3, Bo'n'OM OF PAGE 12. - Page 14 USE DISH SOAP AND AND RINSE. 6. Install the bladder plugged, the top bead of the bladder a light coating WATER SYSTEM - to become useless. A small, screen is positioned over the flow con- clean. To install the screen, place the cone...
-
Page 15: Automatic Shut-Off
12a. Do steps 2 and 3. b. Replace tridge CLEAN). c. Do step 6. d. Turn to page 10 and do the pressure and purging WATER SYSTEM - RO SYSTEM upon installation of the FOR THE PERSON HAVE CLEAN HANDS... -
Page 16: Other Troubleshooting
- CARE OF YOUR HOME DRINKING WATER SYSTEM - IMPORTANT: BEFORE DOING THE FOLLOWING MAINTENANCE, PRESSURE AND ALLOW AIR TO ENTER THE TANK, STEPS 1, 2 AND 3, PAGE 12. t. Replace the prefilter cartridge and postfilter when the amber "FILT" light begins to flash while taking product water from the RO faucet. -
Page 17: Specifications
- DIMENSIONS Supply water pressure limits ... Supply water temperature limits ... Maximum total dissolved solids (TDS) ... Maximum water hardness @ 6.9 pH ... Maximum iron, manganese, hyd. sulfide ... Chlorine in supply water (SEE PAGE 4) ... Supply water pH limits ... Product (quality) water, 24 hrs.* ... -
Page 18: Repair Parts
WaterWorks HOME DRINKING DRAIN ADAPTER "'\ SADDLE VALVE NOTE: Codes in the state of Massachu- setts require installation by _ licensed plumber, and do not permit the use of the saddle valve, For installation, use pFumbfng code 248-CMR of the Commonwealth Massachusetts. - Page 19 WaterWorks HOME DRINKING PART NUMBER DESCRIPTION 7205465 Faucet 1260600 Washer 7207734 Adaptor (Includes key nos. 2 & 4) 9043201 Nut, 3/8" Tubing 7192230 Drain Adapter 9003204 Nut, 1/4" Tubing (6) 7131331 Tubing Insert, 1/4" (5) 7124986 Elbow, 1/4" NPTx 1/4" Tubing 7114509 Tank Shutoff Valve 7116763...
-
Page 20: Remote Installation
- REMOTE INSTALLATION INSTALLING RO ASSEMBLY, Longer lengths of tubing are available from Sears (see page 19) for installingthe RO assembly, and/or water supply saddle valve away from the RO faucet. Examples: In the basement, under the kitchen or bathroom sink. In a closet or room nearby the kit- chen or bathroom.