Advertisement
BEFORE USING WATER FROM YOUR WATER PURIFIER FOR THE FIRST TIME
continued from page 3
The remaining water will boil and pass through the
system as steam to clean all surfaces.
10. The Purifier shuts off automatically
when the
water has boiled away (no more steam coming out of
spout...takes
about 3 hours). After this time, unplug
the power cord at the wall outlet.
11. Shake the storage bottle, then discard the 2 or 3
cupfuls of water which may have some harmless
carbon fines (very fine black particles) in it from the
filter.
MAKING PURIFIED WATER
1. Set the Purifier on your countertop or table.
2. Unplug
the cover cord from its receptacle
(FIG. 1). Holding by the top strap, lift the cover to
remove, and set aside.
3. Fill the tank with tap water up to the max. fill
line (4 quarts). The purifing cycle is shortened
if
you USE HOT WATER.
NOTE: You can purify less than the full amount.
Use this chart as a guide. DO NOT fill the tank with
more than 4 quarts of water because the storage
bottle will overflow.
WHEN YOU FILL WITH
THE CYCLE TAKES
COLD WATER TO...
ABOUT...
1 qt.
1 hr., 35 min.
2 qt.
3 hrs., 5 min.
3 qt.
4 hrs., 35 min.
4 qt. (max. fill line)
6 hrs.,
5 rain.
4. Put the cover on the Purifier and plug the cover
cord into the receptacle.
5. Check to be sure the cover spout containing the
carbon filter is locked in place.
6. Set the storage bottle (cap removed) with the
opening right under the spout.
7. Plug the power cord into any 120 volt outlet.
8. Press the RESET button. The fan motor in the
cover begins to run (check the cover cord plug-in if it
does not).
When the cycle is over the Purifier turns off automati-
cally. AFTER THE FAN MOTOR GOES OFF, WAIT
AT LEAST
30 MINUTES
BEFORE
REMOVING
THE COVER...
WARNING:
NEVER
REMOVE
THE
COVER
WHILE THE FAN MOTOR IS RUNNING, OR FOR
30 MINUTES AFTER IT STOPS. YOU COULD GET
SEVERE BURNS FROM THE BOILING
WATER
OR STEAM.
9. Unplug the Purifier power cord from the wall
outlet.
10. Replace the cap on the storage bottle and store
in the refrigerator until you neet it.
11. After the Purifier has cooled (wait for 30 minutes
after the fan motor stops running) remove the cover
and clean the tank. BE SURE TO HOLD THE COVER
BY THE TOP STRAP AS YOU REMOVE IT
CARE AND CLEANING
OF YOUR WATER PURIFIER
WARNING
ALWAYS BE SURE TO UNPLUG THE PURI-
FIER
POWER
CORD
FROM
THE WALL
OUTLET BEFORE CLEANING,
OR BEFORE
REPLACING PARTS.
STAINLESS STEEL TANK
INSIDE - After each use, rinse the inside with luke-
warm tap water and remove any residue. If a deposit
starts to form at the bottom, use Sears Distiller
cleaner, Stock No. 42-34543. Follow the instructions
on the cleaner bottle. Rub with a soft scouring pad
and rinse thoroughly.
CAUTION:
DO NOT IMMERSE
THE PURIFIER
IN WATER.
OUTSIDE - Wipe the outside of your Purifier with a
soft sponge and mild soap.
NOTICE
THERE ARE NO USER SERVICEABLE PARTS
INSIDE. RETURN THE PURIFIER TO AUTHO-
RIZED SERVICE
PERSONNEL
FOR REPAIR
(SEE PAGE 6).
CHANGING THE CARBON FILTER
The carbon filters in the cover spout (FIG. 2, page 5),
remove odors from the purified water. Replace the
continued, page 5
Advertisement
