Craftsman 315.10924 Owner's Manual
Craftsman 315.10924 Owner's Manual

Craftsman 315.10924 Owner's Manual

7-1/4 inch circular saw. double insulated

Advertisement

612547-480
SEARS
OWNERS
MANUAL
MODEL
NO.
315.109240
CAUTION"
Read Rules for
Safe Operation
and Instructions
Carefully
SAVE
THIS
MANUAL
FOR
FUTURE
REFERENCE
7-1/4
INCH CIRCULAR
SAW.
DOUBLE
INSULATED
Introduction
Operation
Maintenance
Repair Parts
8125.47-480
7-87
Designed
exclusively
for and
sold
onlyby
SEARS,
ROEBUCK
AND
CO.,
Dept.
698/731A,
Sears
Tower.
Chicago,
IL 60684
pf]I_'I:EOPNU
S
A

Advertisement

Table of Contents
loading

Summary of Contents for Craftsman 315.10924

  • Page 1 612547-480 SEARS OWNERS MANUAL MODEL 315.109240 CAUTION" Read Rules for Safe Operation and Instructions Carefully SAVE THIS MANUAL FUTURE REFERENCE SEARS, ROEBUCK 8125.47-480 7-87 7-1/4 INCH CIRCULAR DOUBLE INSULATED Introduction Operation Maintenance Repair Parts Designed exclusively for and sold CO., Dept.
  • Page 2 FULL ONE YEAR WARRANTY If this Craftsman Circular Saw fails to give complete satisfaction within one yearTff_o-_w-the d ate of RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT purchase, Sears will repair it, free of charge. If this circular saw is used for commercial from the date of purchase.
  • Page 3 Lheavy t usea loving doors. nask if ,t from ;ded to Jot use or best anging anging to see it on. ger on )nly ex- marked lg _ and Jes. Do ove cut N OFF. . motor at your Always roleum- Do not qer part...
  • Page 4 SAW BLADES The best of saw blades will not cut efficiently are not kept clean, sharp, and properly dull blade will place a heavy load on your saw and in- crease the danger of kickback. Keep extra blades on hand, so that sharp blades are always available.
  • Page 5 UPPER BLADE GUARD DEPTH OF CUT ADJUSTMENT (wing nut) BLADE WRENCH STORAGE BLADE WRENCH OPERATION SWITCH bevel cut and depth Your saw is equipped directed air flow for reduces storage. must depress order to be able to pull the trigger saw, familiarize...
  • Page 6 BLADE 1. UNPLUG YOUR SAW. 2. Remove blade wrench from Figure 3. Place your saw on a piece of scrap wood as shown in figure 3 with the blade teeth embedded wood. Turn blade screw counterclockwise Remove spring washer, "D"...
  • Page 7 The lower blade guard attached to your circular saw is there for your protection and safety. never be altered for any reason. If it becomes damag- ed, do not operate your saw until the damage has been repaired or replaced. Always leave guard in operating position when using your saw.
  • Page 8 4. Tighten wing nut securely. STARTING A CUT KNOW THE RIGHT WAY TO USE YOUR SAW. See Figure NEVER USE YOUR SAW AS SHOWN NEVER PLACE YOUR HAND ON THE WORKPIECE BEHIND YOUR SAW WHILE MAKING OPERATION (Cont'd.)
  • Page 9 Then place front edge of base on that part of your work that is solidly Figure NEVER PLACE YOUR SAW ON THAT PART OF THE WORK THAT WILL FALL OFF WHEN MADE. See Figure...
  • Page 10 TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cut with the outer edge of the notch in the saw base as shown in figure 12. Since the thickness vary, always make a trial cut in scrap material...
  • Page 11 See Figure 15. Align your line of cut with the inner edge of the notch in the saw base when making full 45 degree bevel cuts.
  • Page 12 GLASSES, BEGINNING ING DUST. ACCESSORIES WERE AVAILABLE 71/4 Saw Blade _ 32303) 71/4 Saw Blade _ 32423) 71/4 Saw Blade _ 32494) 71/4 Saw Blade _ 32564) 100' 14 A.W.G. Ext. Cord (9 83508) or accessories Page 12...
  • Page 13 See Figure 18. If lower tight, the hook on is not engaged with tab on blade to use your saw until lower amount of tension. base assembly, then replace carriage and screw. saw blade. See "To Assemble Blade"...
  • Page 16 Saw, parts or service, Center and most Be sure to provide Circular will'be to the motor housing. PARTS, ALWAYS GIVE OF ITEM Circular from any Sears Ser- stores. stocked locally, your transmitted to a Sears for handling. Chicago, IL 60684...

This manual is also suitable for:

315.109240

Table of Contents