Page 1
Mort.- Fri. 8 a.m. to 5 p.m (CST) CAUTION: Read and Follow all Safety Rules and Instructions Before Operating This Equipment SEARS, ROEBUCK Part No 96596 Revision 3 (6/20195) 5 HORSEPOWER 1800 PSi 2.5 GPM HiGH PRESSURE WASHER Assembly Operation °...
Page 2
• The high pressure equipment is designed to be used with Sears authorized parts onlyo If you use this equipment withpartsthatdonotcomplywithminimum specifications, the user assumes all risksand liabilities° Some chemicalsor detergentsmay be harmful if inhaled...
You can order a spark arrestor through your Sears Service Center, See Repair Parts section of engine for part num- bers, SPECIFICATIONS Adjustable to 1800 psi ...
Page 4
Nozzle, Adjustable ... Nozzle, Optional Turbo ... Engine ... Pump ... Operation Detergent Application ... Know Your Pressure Washer ... 9 Stopping ... To Start Engine ... To Turn on Washer ... Using Adjustable Nozzle ... Order Parts ... back page RESPONSIBILITIES PARTS ...
NECT KIT QUICK CONNECT TURBO NOZZLE - 1800 PSI 2200 and 2500 PSI Most Sears stores can order these items for you when you Some of these accessories may not apply to your pressure UTILITY BRUSH KIT 18" STAINLESS STEEL EXTENSION , ...
Page 6
CONTENTS OF HARDWARE ,_r.__f Main Unit High Pressure Hose Parts Bag contents shown full size (fasteners) (2) Axle Pins (2) Hex Head Capscrews - M8 x 40mm (2) Washers - #10 (2) Self-drilling Capscrews (2) Lock Washers - 5/8" #10-16 Parts packed separately in carton...
Before you can operate your new high pressure washer, you must assemble the wheel kit and properly connect the high pressure hose. IF YOU HAVE ANY PROBLEMS WITH THE ASSEMBLY...
• Provide proper water supply (not to exceed t40°F)o Be sure to read "Safety Rules" and "Operation" sec- tions before using the pressure washer. If tape is not • !\ FIG. 6 FIG.
KNOW YOLIR HIGH PRESSURE WASHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE WASHER. Compare the illustrations with your high pressure washer to familiarize yourself with the locations of various controls and adjustment& Save this manual for future reference.
NOTE: A small amount of water will squirt out when you release the pressure. SPRAY NOZZLES Your high pressure washer comes equipped with an adjust- able nozzle (Fig. t2)o Attach nozzle as shown in Fig. 10 and HAND TIGHTEN the plastic knob. Figure 12 shows the optional turbo nozzle.
Page 11
Leave the solution on surface for 3 to 5 minutes to a ow so ution to work. The second step involves cleaning the surface you have prepared with the pressure washer and then rinsing it clean, To apply detergent follow these steps: •...
Check your engine oil level more frequently to avoid possi- ble damage from running low on oil. Oil sump capacity is 20 ounces. • Position pressure washer so engine is level. Clean area around oil fill plug and remove oil fill plug (Fig. 18). FIG. 18 Fill oil crankcase to point of overflowing.
WATER SUPPLY CONNECTED AND TURNED ON, YOU MUST FOLLOW THIS CAUTION OR THE PUMP WILL BE DAMAGED. Press trigger on pressure washer wand to relieve high pressure and/or purge the inlet hose of air. • Move throttle control to FAST position (Fig. 19).
* Change sooner when operating under heavy load or high ambient temperature° GENERAL RECOMMENDATIONS The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or neg- ligence. To receive full value from the warranty, operator must maintain high pressure washer as instructed in this manual.
Clean or replace more often if operating under dusty or dirty conditions. Replacements are available at your local Sears Authorized Service Center_ To clean or replace air cleaner (Fig. 24), follow these steps:...
CUSTOMER CLEAN COOUNG SYSTEM • Clean dirt or chaff from finger 0uard or rotating screen even] 8 hours to prevent engine damage caused by ovedleating (Fig. 25), Keep dirt and combustible debris off of muffler area. REPLACE SPARK PLUG Change the spark plug every 100 hou rs of operation or' once each year, whichever comes first, This will help engine to start easier and run better.
Page 17
WATER HEATER, OR OTHER GAS APPLIANCE, If you do not plan to use the Pressure Washer for more than 30 days, you must prepare the engine for long term storage. NOTE: As always, prepare the pressure washer pump as you would after each use°...
Page 18
8o Provide cooler water supply, 9. Clear blocks in outlet hose, 10,, Replace gun, 1to Clear no.leo 12o Contact Sears Service Department. 1. Insertchemical line intodetergent. 2° Clean or replace fitter/detergent line. 3 Push nozzle forward for low pressure mode°...
Page 19
CRAFTSMAN 1800 PSI HIGH PRESSURE DESCRIPTION PART NO. ITEM 5 hp Briggs & Straiten Engine (1 req,) 95998 Pump (1 req,) 87628 Brass Water Hose Connector (t req,) 89647 Quick-connect, 96016 Quick-connect, 95456 5/16" Conical Lock Washer (4 req,) 92479 5/16"-24 x 3/4"...
Page 20
CRAFTSMAN 1800 PSi HIGH PRESSURE BRIGGS & STRATTON 4-CYCLE WASHER 580.751510 ENGINE 133212-0159-01 36 35 ,f' 0 _"( _ _ J'-&_ \%. __, REPAIR PARTS 1_o_9 LABEL K_TI _ REQUIRES SPECIAL TOOLS TO INSTALL. SEE REPAIR INSTRUCTION MANUAL°...
Page 24
CRAFTSMAN 1800 PSi HIGH PRESSUREWASHER 580.751510 BRIGGS & STRATTON4-CYCLE ENGINE 133212-0159-01 Ref. Part Part Name 495133 Cyilnder Assembly Oil Seal *299819 214040 Cylinder Head *272157 Cylinder Head Gask,_t Breather - Valve Chamber 294178 Valve Cover Gasket *27459 04621 Screw. Breather Mounting Sam Breather Tube Grommet 66576 *270080...
Page 25
FULL ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER For one year from the date of purchase, when this Craftsman High Pressure Washer is maintained and operated according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and workmanship°...
Page 26
CRAFTSMAN 1800 PSI HIGH PRESSURE ITEM KIT PART NO. DESCRIPTION 96737 Pressure Reglulator Knob 96738 Ring Nut 96739 Spring Guide Spring Plate Upper Piston O-ring Piston Guide 89361 O-ring 89361 O-ring Lower Piston Combiset Body 96740 Set Screw (2 reqo) O-ring O-ring 96741...
Page 27
CRAFTSM AN 1800 PSI HIGH PRESS UR E WASHER ,KIT 89360 KIT 89358 -_'-"'_IL('ll! .:ll //fP'_ DESCRIPTION KIT PART NO. ITEM M6 x 60ram Head Bolt (6 req,) 96742 1/8" Plug [optional] (1 req.) Inlet/outlet Valve Cap (6 req) Valve Cap O-dng (6 reqo) Inlet/outlet Valve (6 reqo) Inlet/outlet Valve O-ring (6 req.) Water Seal (3 req.)
Page 28
The model number for your pressure washer will be found on a decal attached to the uniL The part number for your engine will be found in the parts list. All parts listed herein may be ordered through Sears, Roebuck and Co. Service Centers and most Retail Stores. WHEN...