Microprocessor controlled, fully automatic operation battery charger with engine starter plus battery and alternator tester for 6 and 12-volt batteries (17 pages)
Page 1
SEA/RS OWNER'S MANUAL Model No. 200.71460 CAUTION: Read and Follow All Safety Rules and Operating Instructions Before Every Use of this Product. Sears, Roebuck 60/20/2 MANUAL CHARGER 250/125 ENGINE STARTER BATTERY and Co., Hoffman Estates, IL 60179 BATTERY with TESTER...
FULL FIVE-YEAR WARRANTY If, within FIVE years from the date of purchase, this battery charger fails due to a defect in materials or work- manship, simply RETURN IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will repair or replace it, free of charge.
This may spark or short circuit the battery or another electrical device that may cause an explosion. • Always operate your battery charger in an open, well ventilated area • Never smoke or allow a spark or flame in the vicinity of the battery or engine.
Parts The exploded view of your charger shows parts, their location, and a keyed chart identifying each part by name and pert number. The wiring diagram provides additional reference for the professional repair person. Item De=mrlpUon Ples_c cap Top Hub Cap Wheel Axle Power Cord...
Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use.
3. Tap the other axle cap onto the opposite end of the axle and place the axle assembly onto the bottom of the charger. Place one end of the bracket into slot, then place the axle assembly under each bracket. Fasten the other side of the brackets using the two 10-32 screws provided.
TEMPORARY adapter may be used to connect the charger to a two-pole outlet if a properly grounded outlet is not available. Use the adapter ONLY until a properly grounded outlet can be installed by a qualified electrician. DANGER: Before using an adapter as illustrated, be certain that the center screw of the outlet plate is grounded.
Your To obtain the best results from your battery charger, you must know how to use it properly. This section will tell you how to set the controls, and how you can charge a battery while it is still in the vehicle, or you can remove it and then charge it.
Page 9
VOLTMETER: an accurate reading of your battery's voltage before you begin charging it, use the voltmeter as follows: 1. Set the timer to the OFF position, turn the voltage selector switch to 12 or 6 volt, according to the battery you are testing, and then connect the charger as indicated in the "Charging your battery in the vehicle"...
Charging Your Battery Charging your battery in the vehicle: 1. Arrange the power cord and charging leads care- fully in order to avoid damage that could be caused by the hood, door, or moving engine parts. 2. Keep clear ofthe fan blades, belts, pulleys, and other parts that can cause injury.
Page 11
(1) from the chassis connection and, (2) from the battery post. 12. Clean and store the battery charger in a dry location. Charging your battery outside the vehicle: 1. Remove the battery from vehicle, making sure to disconnect grounded terminal first with all accesso- ries and lights turned off in the vehicle.
Calculating charge time The Chart Method Use the following table to more accurately determine the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. • Small batteries-- motorcycles, garden tractors, etc. -- are usually rated in Ampere Hours (AH).
Using the engine Your battery charger can be used to jump-start your car if the battery is low. Follow these instructions on how to use the engine start feature. 1. Set the VOLT/AMP SELECTOR and timer switches to the OFF position.
Circuit breaker cycles when current draw is too high. Separate the clamps. Check for worn cables and replace if needed. Have a Sears technician test the battery. Correct connections. Correct Volt/Amp Selector setting. Crank time varies with the amount of current drawn, if cranking draws more than 250 amps, crank time may be less than 5 seconds.
Page 15
250/125 ENGINE STARTER BATTERY TESTER Forinformation abouttroubleshooting Calltoll-free f rom anywhere inthe U.S.A. 7 amto 4:30 pm CSTMonday through Friday 1-800-SEARS-64 (1-800-732-7764) Forthe repairor replacement partsyouneed Call7 am - 7 pro,7 daysa week 1-800-366-PART (1-800-366-7278) Forthe location of a SearsRepair...