Page 2
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 3
The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000- 3-2/1995;...
TABLE OF CONTENTS ...III Your New LCD Monitor Unpacking Identifying Components Adjusting the Tilting Angle Connecting AC Power and Video Cable Power Management System The LCD Monitor’s Control Panel Adjusting the Monitor’s Display TFT LCD Monitor Specifications Supported Timing Troubleshooting ABLE OF ONTENTS...
Your New LCD Monitor Your LCD Monitor has been designed to be versatile, ergonomic and user-friendly. The LCD Monitor is capable of displaying most standards, from 640x400 VGA to 1280x1024 SXGA. The digital controls located on the front panel allow the user to easily adjust the Monitor’s display parameters, and the LCD Monitor’s small footprint gives you more room in your workspace for other peripherals.
Page 6
After unpacking your LCD monitor, make sure the following items are included in the box and are in good condition: • LCD monitor • Power Cord • Monitor-To-PC Analog signal cable 15pin • User’s manual If you find that any item to be missing or appear to be damaged, contact your dealer immediately.
Identifying Components A. The LCD Monitor — Front View Figure 1-1: The LCD Monitor Front View 1. Power-On Indicator This Circular LED indicator green lit when the power is on and orange lit when the LCD monitor is in power-saving mode. 2.
Page 8
B. "Hot Keys" for Quick Adjustment of Monitor Settings Figure 1-2: "Hot Keys" 1. Brightness Adjustment "hot key": Brightness Press this + button to allow you to adjust the brightness of the LCD Monitor directly 2. Contrast Adjustment “ Hot key” Contrast Press this - button to allow you to adjust the contrast of the LCD Monitor...
Connecting AC Power and Video Cable Note: Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. Power Management System This LCD Monitor complies with the VESA DPMS power management proposal. When the LCD Monitor is in power-saving mode or detects an incorrect timing, the monitor screen will be blank and the power LED indicator from green lit change to orange lit.
The LCD Monitor’s Control Panel : Enable the OSD Menu button or / Move the cursor to the left ( when OSD is enabled) : Move the cursor to the Right ( When OSD is enabled) / Auto-adjustment hot key 3.
Adjusting the Monitor’s Display OSD Main Menu 1. Pressing the button causes the screen below to appear. 2. Use the & key to select the desired group, then press – or + key to enter into sub-menu 3. Repeat step 2 to select the changed item, then – or + to change the value.
Page 13
Monitro Adjustment Allow you to adjust the LCD monitor’s display settings. Press the Adjustment control button to display the submenu. Use the Function Select button to select one of the following submenu options: Auto Adjustment (For VGA port only, DVI port can’t adjustment) Press the Adjustment control button to let the monitor determine and select the setting that is most appropriate for your system requirements.
Page 14
To exits the Monitor-Control submenu OSD-control The OSD-Control menu lets you adjust the position of the OSD on the screen. Press the Adjustment control button to display the submenu. OSD-H-POSITION: To change the position of the OSD on a horizontal plane. OSD-V-POSITION: To change the position of the OSD on a vertical plane.
Page 15
COLOR: To select the LCD monitor’s color display. The available options are cold, warm and User. Selecting the user option lets you make individual adjustments to the R, G and B items. COLOR R, G and B ADJUST: To make individual adjustments to the Red, Blue, Green (RGB) gain for the color temperat AUTO LEVEL: To adjust automatically the white balance display.
Page 16
To indicate display mode timings and firmware version. EXIT: To exit the Misc-Control submenu. EXIT: Use the OSD Exit item to close the OSD menu. The OSD will disappear by itself if left inactive. Rev.1...
Note: 1) No video No Video When the monitor is ON and there is no video signal received, the following message will be displayed 2) Signal out of range When the frequency range of the signal is out of the Monitor’s specifications, (over 85HZ) the display will show the following message Over Range Rev.1...
TFT LCD Monitor Specifications LCD Panel Control Functions Power On-Screen Main Menu Display MONITOR- (OSD) CONTROL OSD-CONTROL MISC-CONTROL GRAPHIC- CONTROL EXIT Display Area (mm) Display Colors Video Interface Appendix A 17" SXGA Software Power switch with LED indicator (ON/OFF) Submenu Auto Adjustment, H-POSITION, V- POSITION, PHASE, CLOCK, GRAPHIC/TEXT, RESET, EXIT...
Page 19
Scanning Frequency H/V, Hz Power Management Power Consumption (ON/OFF, W) Dimensions WxHxD Net Weight (approx.) Power Supply Environment Regulatory 24-80K 50-75 Meets VESA DPMS 35W/1W Max. 14.74 x 15.10 x 6.81 in. (374.5 x 383.45 x 173mm) 9.46 lbs (4.3 Kg) Universal Input AC Socket Operating Temperature: 32 to 104°F (0 to 40°...
Supported Timing Item Standards NEC PC98 MAC 13" mode MAC 16" mode MAC 17" mode VESA VESA VESA SVGA VESA VESA VESA VESA VESA VESA *Once a mode is optimized, there is no need to make any further adjustment as long as the VGA card remains unchanged. *Specifications are subject to change without notice.
Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected. Before applying any of the following troubleshooting procedures, you should first apply the Auto Adjust option in the OSD menu.
Page 22
4. If the power LED is not lit, check that the AC power connector is securely connected, and verify that the AC adapter LED is lit. If the AC adapter LED is not lit, please contact your dealer for assistance. PROBLEM: The LCD displays “signal out of range”...