Page 1 2009 Saturn AURA Green Line Hybrid Owner Manual Seats and Restraint System ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-9 Safety Belts ... 1-11 Child Restraints ... 1-30 Airbag System ... 1-56 Restraint System Check ... 1-72 Features and Controls ... 2-1 Keys ...
Page 2: Canadian Owners
GENERAL MOTORS and GM are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. Saturn reserves the right to make changes after that time without further notice. This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3 Index To quickly locate information about the vehicle use the Index in the back of the manual. It is an alphabetical list of what is in the manual and the page number where it can be found. Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means...
Page 4 Vehicle Symbols The vehicle has components and labels that use symbols instead of text. Symbols are shown along with the text describing the operation or information relating to a speciﬁc component, control, message, gage, or indicator. : This symbol is shown when you need to see your owner manual for additional instructions or information.
Page 5: Table Of Contents
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Power Seats ...1-3 Manual Lumbar ...1-4 Heated Seats ...1-4 Reclining Seatbacks ...1-5 Head Restraints ...1-8 Power Lift Seat ...1-9 Rear Seats ...1-9 Split Folding Rear Seat ...1-9 Safety Belts ...1-11 Safety Belts: They Are for Everyone ...1-11 How to Wear Safety Belts Properly ...1-16 Lap-Shoulder Belt ...1-24 Safety Belt Use During Pregnancy ...1-29...
Page 6 Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 7 Power Seats If the vehicle has power seats, the controls used to operate them are located on the outboard side of the seats. To adjust the seat: • Move the seat forward or rearward by sliding the control forward or rearward. •...
Page 8 Manual Lumbar On vehicles with this feature, the handle is located on the outboard side of the seat. Move the handle up or down repeatedly to decrease or increase lumbar support. Heated Seats On vehicles with heated front seats, the buttons are located on the outboard side of the driver’s and front passenger seats.
Page 9 Reclining Seatbacks Manual Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 10: Power Reclining Seatbacks
To return the seatback to an upright position: 1. Lift the lever fully without applying pressure to the seatback and the seatback returns to the upright position. 2. Release the lever to lock the seatback. 3. Push and pull on the seatback to make sure it is locked.
Page 11 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 12 Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. Pull the restraint up to raise it.
Page 13 Power Lift Seat To adjust a power lift seat, press the top or bottom of the power lift seat switch to raise or lower the seat. Rear Seats Split Folding Rear Seat With this feature, either side of the seatback can be folded down for more cargo space.
Page 14 To lower the rear seatback, pull up on the seatback strap while folding the seatback down. This allows access to the trunk. To raise the rear seatback pull the seatback up and make sure it latches. Push and pull on the seatback to be sure it is locked in position.
Page 15 Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
Page 16: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 1-12...
Page 17 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-13...
Page 18 or the instrument panel... 1-14 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Page 19 Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 20 How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 1-30 or Infants and Young Children on page 1-34.
Page 21 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 22 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. 1-18 CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 23 What is wrong with this? The belt is buckled in the wrong buckle. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 24 What is wrong with this? The belt is over an armrest. 1-20 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 25 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 26 What is wrong with this? The belt is behind the body. 1-22 CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 27 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 28 Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly. 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. To see how, see “Seats” in the Index. 2.
Page 29 5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Page 30 Shoulder Belt Height Adjuster Your vehicle has a shoulder belt height adjuster for the driver and right front passenger position. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off of the shoulder.
Page 31 There is one guide for each outboard passenger position in the rear seat. Here is how to install a comfort guide to the safety belt: 1. Pull the elastic cord out from between the edge of the seatback and the interior body to remove the guide from its storage clip.
Page 32 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. 1-28 CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 33 4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that the safety belt can be removed from the guide.
Page 34 Safety Belt Extender If the safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 35 The manufacturer’s instructions that come with the booster seat state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue.
Page 36 CAUTION: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time. 1-32...
Page 37 CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 38 Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 39 CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 40 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 41 For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
Page 42 Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. A forward-facing child seat (B) provides restraint for the child’s body...
Page 43: Securing The Child Within The Child Restraint
Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle’s safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual.
Page 44 Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint;...
Page 45 When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. Wherever you install a child restraint, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle.
Page 46: Lower Anchors And Tethers For Children
A. Child restraint or occupant using safety belt A. Child restraint or occupant using safety belt B. Child restraint using LATCH 1-42 Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier.
Page 47: Top Tether Anchor
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Page 48 Your child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor. Some child restraints with top tethers are designed for use with or without the top tether being attached. Others require the top tether always to be attached.
Page 49 To assist you in locating the lower anchors, each rear anchor position has a label, near the crease between the seatback and the seat cushion, showing where the anchors are located. The top tether anchors are located behind the rear seat on the ﬁller panel.
Page 50: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came with the child...
Page 51 CAUTION: (Continued) Pull the shoulder belt all the way out of the retractor to set the lock, if your vehicle has one, after the child restraint has been installed. Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts.
Page 52 This system is designed to make installation of child restraints easier. When using lower anchors, do not use the vehicle’s safety belts. Instead use the vehicle’s anchors and child restraint attachments to secure the restraints. Some restraints also use another vehicle anchor to secure a top tether.
Page 53: Securing A Child Restraint In A
If the position you are using has an adjustable headrest or head restraint and you are using a single tether, route the tether under the headrest or head restraint and in between the headrest or head restraint posts. See Head Restraints on page 1-8.
Page 54 If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint on page 1-40. 1. Put the child restraint on the seat. 2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint.
Page 55 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 56: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-40. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag and seat-mounted side impact airbag under certain conditions.
Page 57 If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-42 for how and where to install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH) on page 1-42 for top tether anchor locations.
Page 58 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
Page 59 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 60: Airbag System
Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. • A seat-mounted side impact airbag for the driver. • A seat-mounted side impact airbag for the right front passenger.
Page 61 CAUTION: Airbags inﬂate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Page 62: Where Are The Airbags
There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-28 for more information.
Page 63 The right front passenger’s frontal airbag is in the instrument panel on the passenger’s side. Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
Page 64 Driver Side shown, Passenger Side similar The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows. 1-60 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 65: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 66 Frontal airbags are not intended to inﬂate during vehicle rollovers, rear impacts, or in many side impacts. In addition, the vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity. The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact.
Page 67: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inﬂator. Gas from the inﬂator ﬁlls the airbag causing the bag to break out of the cover and deploy. The inﬂator, the airbag, and related hardware are all part of the airbag module.
Page 68: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the frontal airbags and seat-mounted side impact airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize an airbag inﬂated. Roof-rail airbags may still be at least partially inﬂated for some time after they deploy.
Page 69: Instrument Panel
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 70 The passenger sensing system turns off the right front passenger frontal airbag and seat-mounted side impact airbag under certain conditions. The driver airbags and the roof-rail airbags are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat.
Page 71 The passenger sensing system is designed to turn off the right front passenger airbag and seat-mounted side impact airbag if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a rear-facing infant seat. •...
Page 72: Child Restraint
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 73 If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag and seat-mounted side...
Page 74: Servicing Your Airbag-Equipped Vehicle
Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
Page 75 Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 76: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Page 77: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as...
Page 78 ✍ NOTES 1-74...
Page 79: Features And Controls
Section 2 Keys ...2-2 Remote Keyless Entry (RKE) System ...2-3 Remote Keyless Entry (RKE) System Operation ...2-4 Remote Vehicle Start ...2-7 Doors and Locks ...2-9 Door Locks ...2-9 Power Door Locks ...2-9 Door Ajar Reminder ...2-9 Delayed Locking ...2-10 Programmable Automatic Door Locks ...2-10 Rear Door Security Locks ...2-11 Lockout Protection ...2-12 Trunk ...2-12...
Page 80: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 81: Remote Keyless Entry (Rke) System
Remote Keyless Entry (RKE) System If this vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 82: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-3. With Remote Start Shown, Without Remote Start Similar...
Page 83: Programming Transmitters To The Vehicle
The high-beam headlamps, parking lamps, and back-up lamps may come on each time See “EXT (Exterior) LIGHTS” under DIC Vehicle Personalization on page 3-48 for additional information. Pressing on the RKE transmitter disarms the content theft-deterrent system. See Content Theft-Deterrent on page 2-17. (Remote Trunk Release): Press and hold for about one second to unlock the trunk.
Page 84: Battery Replacement
Battery Replacement Replace the battery if the KEY FOB BATT (Battery) LOW message displays in the DIC. See “KEY FOB BATT (Battery) LOW” under DIC Warnings and Messages on page 3-44 for additional information. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter.
Page 85: Remote Vehicle Start
Remote Vehicle Start Your vehicle may have a remote starting feature that allows you to start the engine from outside the vehicle. It may also start the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active and the vehicle has an automatic climate control system, it will automatically regulate the inside temperature.
Page 86 The engine will shut off automatically after 10 minutes, unless a time extension has been done or the vehicle’s key is inserted into the ignition switch and turned to ON/RUN. To manually shut off a remote start, do any of the following.
Page 87: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 88: Delayed Locking
Delayed Locking This feature allows the driver to delay the locking of the vehicle. It will not operate with the key in the ignition. See Lockout Protection on page 2-12. Press the driver power door lock switch or the Remote Keyless Entry (RKE) transmitter lock button once.
Page 89: Rear Door Security Locks
Rear Door Security Locks Rear door security locks prevent passengers from opening the rear doors from the inside. The rear door security locks are located on the inside edge of each rear door. The rear doors must be opened to access them. To assist in ﬁnding the lock, the vehicle will have one of the following: To use these locks:...
Page 90: Lockout Protection
Lockout Protection This feature prevents the driver door from being locked using the power door locks, if the key is left in the ignition and a door is open. Press the power door lock switch to lock all the doors and then unlock the driver door.
Page 91: Remote Trunk Release
Remote Trunk Release On vehicles with this feature, press the button located on the driver’s door near the map pocket to open the trunk. The trunk can only be opened while the vehicle is in P (Park). To close the trunk use the pullstrap located on the trunk lid.
Page 92: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 93: Power Windows
Power Windows The power window switches are located on the armrest on the driver’s door. In addition, there is a switch on each passenger door. Express-Down Window The driver window has an express-down feature. This switch is labeled AUTO. Press the front all the way down and release, to automatically lower.
Page 94 Express Window Anti-Pinch Feature If any object is in the path of the window when the express-up is active, the window stops at the obstruction and auto-reverse to a preset factory position. Weather conditions such as severe icing may also cause the window to auto-reverse.
Page 95: Sun Visors
Sun Visors To block out glare, swing down the visors. They can also be removed from the center mount and swung to the side, to block out glare from the side. The visors also have extenders that can be pulled out. The vehicle may have lighted visor vanity mirrors located on the passenger and driver side visors.
Page 96: Disarming The System
Disarming the System To disarm the system, do one of the following: • Press the RKE transmitter unlock button. • Turn the ignition to ON/RUN. Once the system is disarmed, the security light will stop ﬂashing. How the System Alarm is Activated To activate the system if it is armed: •...
Page 97: Pass-Key Iii+ Electronic Immobilizer
® PASS-Key III+ Electronic Immobilizer The PASS-Key III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 98 If the engine still does not start, and the key appears to be not damaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses on page 5-83. If the engine still does not start with the other key, your vehicle needs service.
Page 99: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km).
Page 100: Retained Accessory Power (Rap)
On vehicles with an automatic transmission, the shift lever must be in P (Park) to turn the ignition switch to LOCK/OFF. The steering can bind with the wheels turned off center. If this happens, move the steering wheel from right to left while turning the key to ACC/ACCESSORY.
Page 101: Starting Procedure
Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed goes down as your engine gets warm. Do not race the engine immediately after starting it.
Page 102 Automatic Engine Start/Stop CAUTION: Exiting the vehicle, without ﬁrst shifting into P (Park), may cause the vehicle to move, you or others may be injured. Because the vehicle has the Automatic Engine Start/Stop feature, the vehicle’s engine might seem to be shut off, however, once the brake pedal is released, the engine will start up again.
Page 103 The Engine Will Remain Running When: • The engine, transmission, or hybrid battery is not warmed up yet. • The outside temperature is less than 5°F (−15°C). • While the A/C is in Normal Mode. • A/C is in Hybrid Mode and the climate control system is working to cool the vehicle.
Page 104: Engine Coolant Heater
Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below 0°F (−18°C). Vehicles with an engine coolant heater should be plugged in at least four hours before starting. Some models may have an internal thermostat in the cord which will prevent engine coolant heater operation at temperatures above 0°F (−18°C).
Page 105: Automatic Transmission Operation
Automatic Transmission Operation The shift lever is located on the console between the seats. There are several different positions for the automatic transmission. P (Park): This position locks the front wheels. It is the best position to use when you start the engine because the vehicle cannot move easily.
Page 106 R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.
Page 107: Parking Brake
I (Intermediate): This position is also used for normal driving. However, it reduces vehicle speed without using the brakes for slight downgrades. If constant upshifting or downshifting occurs while driving up steep hills, this position can be used to prevent repetitive shifts. You might choose I (Intermediate) instead of D (Drive) when driving on hilly, winding roads, so that there is less shifting between gears.
Page 108: Regenerative Braking
The PUSH PARK PEDAL message will also appear in the Driver Information Center (DIC) to remind you to release the parking brake. See DIC Warnings and Messages on page 3-44. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts.
Page 109: Torque Lock
Leaving the Vehicle With the Engine Running CAUTION: It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre.
Page 110: Shifting Out Of Park
Shifting Out of Park The vehicle is equipped with an electronic shift lock release system. The shift lock release is designed to: • Prevent ignition key removal unless the shift lever is in P (Park) with the shift lever button fully released, and •...
Page 111: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airﬂow or tail pipes).
Page 112: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Exiting the vehicle, without ﬁrst shifting into P (Park), may cause the vehicle to move, and you or others can be seriously injured.
Page 113: Mirrors
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to reduce the glare of headlamps from behind. Push the tab forward for daytime use and pull it for nighttime use.
Page 114: Outside Automatic Dimming Mirror
Outside Automatic Dimming Mirror If the vehicle has this feature, the driver side mirror adjusts for the glare of headlamps behind you. This feature is controlled by the automatic dimming inside rearview mirror. See Manual Rearview Mirror on page 2-35 for more information. ®...
Page 115 OnStar Services Available with the Safe & Sound Plan • Automatic Notiﬁcation of Airbag Deployment • Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • Remote Door Unlock/Vehicle Alert •...
Page 116: Onstar Virtual Advisor
OnStar Virtual Advisor OnStar Virtual Advisor is a feature of OnStar Hands-Free Calling that uses minutes to access location-based weather, local traffic reports, and stock quotes. Press the phone button and give a few simple voice commands to browse through the various topics.
Page 117: Storage Areas
The vehicle must have a working electrical system, including adequate battery power, for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any particular time or place. Some examples are damage to important parts of the vehicle in a crash, hills, tall buildings, tunnels, weather or wireless phone network congestion.
Page 118: Center Console Storage
Pull down the door on the back of the center console to use the rear seat cupholders. Center Console Storage There is a center console with two storage areas. Lift the passenger side lever to access the upper storage tray. Lift the driver side lever to access the lower storage area.
Page 119 Press the back of the switch and release it to open the sunroof to the vent position. From the vent position, press and release the back of the switch to express-open the sunroof. To stop the sunroof from express opening, press the switch again.
Page 120 ✍ NOTES 2-42...
Page 121 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Horn ...3-6 Tilt and Telescopic Steering Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-8 Windshield Washer ...3-9 Cruise Control ...3-10 Headlamps ...3-13 Headlamps on Reminder ...3-13 Headlamps Off in Park ...3-14...
Page 122: Audio System(S)
Section 3 Oil Pressure Light ...3-36 Security Light ...3-37 Cruise Control Light ...3-37 Highbeam On Light ...3-37 Fuel Gage ...3-38 Auto Stop Mode ...3-39 Charge/Assist Gage ...3-39 Fuel Economy Light ...3-40 Driver Information Center (DIC) ...3-40 DIC Operation and Displays ...3-41 DIC Warnings and Messages ...3-44 DIC Vehicle Personalization ...3-48 Instrument Panel...
Page 123 ✍ NOTES...
Page 124: Instrument Panel Overview
Instrument Panel Overview...
Page 125 The main components of the instrument panel are the following: A. Outlet Adjustment on page 3-24. B. Turn Signal/Multifunction Lever on page 3-7. C. Instrument Panel Cluster on page 3-25. D. Windshield Wipers on page 3-8 and Windshield Washer on page 3-9. E.
Page 126: Hazard Warning Flashers
Hazard Warning Flashers (Hazard Warning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press again to turn the ﬂashers off. Horn Press near or on the horn symbols on the steering wheel pad to sound the horn.
Page 127: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: : Turn and Lane-Change Signals : Headlamp High/Low-Beam Changer : Exterior Lamp Control Flash-to-Pass. Information for these features is on the pages following. Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or...
Page 128: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you. This instrument panel cluster light high beam lamps are turned on while the ignition is in ON/RUN. To change the headlamps from high beam to low beam, pull the turn signal lever toward you.
Page 129: Windshield Washer
(Delay): While the lever is in the intermittent position, turn the intermittent adjust band with this symbol on it up or down to select a shorter or longer delay between wiping cycles. To the left of the adjust band are bars, increasing in size from bottom to top, that indicate the frequency of the wipes.
Page 130: Cruise Control
Cruise Control Cruise control lets a speed of about 25 mph (40 km/h) or more be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below 25 mph (40 km/h). CAUTION: Cruise control can be dangerous where you cannot drive safely at a steady speed.
Page 131: Resuming A Set Speed
(On/Off): Press to turn the cruise control system on and off. RES+ (Resume): Press to resume a set speed and to accelerate the speed. SET− (Set): Press to set a speed and to decrease the speed. To set a speed do the following: 1.
Page 132 Reducing Speed While Using Cruise Control If the cruise control system is already engaged: • Press and hold the SET− until the desired lower speed is reached, then release it. • To slow down in very small amounts, brieﬂy push the SET−.
Page 133: Headlamps
Headlamps The band on the lever on the outboard side of the steering column operates the exterior lamps. The exterior lamp control has the following four positions: (Headlamps): Turns on the headlamps, parking lamps, and taillamps. (Parking Lamps): Turns on the parking lamps and taillamps only.
Page 134: Headlamps Off In Park
Headlamps Off in Park This feature works when the ignition is in the ON/RUN position and it is dark outside. To turn the headlamps off when it is dark outside but keep other exterior lights on, turn the exterior lamp control to the parking lamp position.
Page 135: Automatic Headlamp System
Automatic Headlamp System When it is dark enough outside, the automatic headlamp system turns on the headlamps at the normal brightness along with other lamps such as the taillamps, sidemarker, parking lamps, and the instrument panel lights. The radio lights will also be dim. The vehicle has a light sensor on top of the instrument panel that controls the automatic headlamp system.
Page 136: Dome Lamps
Dome Lamps The dome lamps come on when any door is opened. They turn off after all the doors are closed. The dome lamps can also be turned on by turning the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
Page 137: Battery Run-Down Protection
The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads.
Page 138: Accessory Power Outlet(S)
Accessory Power Outlet(s) Accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular telephone. There are two accessory power outlets. One accessory power outlet is inside the center storage console and the other is located on the center storage console below the climate controls.
Page 139: Climate Controls
Climate Controls Automatic Climate Control System The heating, cooling, and ventilation in the vehicle can be automatically controlled with this system. A. Fan Control E. Rear Window Defogger B. Air Conditioning F. Air Delivery Mode C. Recirculation Control D. Hybrid Air G.
Page 140: Automatic Operation
Automatic Operation AUTO (Automatic): Select AUTO on both the fan speed knob and the air delivery mode knob to activate the automatic system. When automatic operation is active the system controls the inside temperature and air delivery. Use the steps below to place the entire system in full automatic control: 1.
Page 141: Manual Operation
Manual Operation The air delivery mode or fan speed, can manually be adjusted. (Off): Turns the fan off. Outside air still enters the vehicle. The direction can be changed by changing the mode position. The temperature can also be adjusted using either the up or down arrow temperature buttons.
Page 142: Maximum Air Conditioning
While in this mode, the hybrid system does not shut the engine down at complete stops. On hot days, open the windows long enough to let hot inside air escape. This reduces the time it takes for the vehicle to cool down. Then keep the windows closed for the air conditioner to work its best.
Page 143: Rear Window Defogger
When the heater is in use, there might be slight noise or vibration during Auto Stops. This is due to the coolant circulation pump that continues to circulate heat through the system during the engine Auto Stop. The heater works best if the windows are kept closed. (Recirculation): Press to turn on the recirculation mode.
Page 144: Outlet Adjustment
Outlet Adjustment There are four main air outlets on the instrument panel. Move the lever located in the center of each outlet side-to-side or up and down, to change the direction and amount of airﬂow in the vehicle. The center thumbwheel does not control the main outlets.
Page 145: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, how much fuel the vehicle has used, and many other things needed to drive safely and economically. United States version shown, Canada Similar 3-25...
Page 146: Speedometer And Odometer
Speedometer and Odometer The speedometer shows the vehicle speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). This vehicle has a tamper resistant odometer.
Page 147: Safety Belt Reminders
Safety Belt Reminders Driver Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind the driver to fasten the safety belt, unless the driver safety belt is already buckled. The driver safety belt light comes on and stays on for several seconds, then ﬂashes for several more.
Page 148: Airbag Readiness Light
Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Page 149: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator The vehicle has a passenger sensing system. See Passenger Sensing System on page 1-65 for important safety information. The instrument panel has a passenger airbag status indicator. United States When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
Page 150: Charging System Light
Charging System Light This light comes on brieﬂy when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer.
Page 151: Antilock Brake System (Abs) Warning Light
This light comes on brieﬂy when the ignition key is turned to ON/RUN. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light will then go off. When the ignition is on, the brake system warning light also comes on when the parking brake is set.
Page 152: Electronic Stability Control (Esc)/Traction Control System (Tcs) Indicator/Warning Light
Electronic Stability Control (ESC)/ Traction Control System (TCS) Indicator/Warning Light The Electronic Stability Control (ESC) system or the Traction Control System (TCS) indicator/ warning light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by the dealer/retailer.
Page 153: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Warning Light This light indicates that the engine coolant has overheated or the radiator cooling fan is not working. This light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by the dealer/retailer.
Page 154: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. This light comes on when the ignition is on, but the engine is not running, as a...
Page 155 The following can prevent more serious damage to the vehicle: • Reduce vehicle speed. • Avoid hard accelerations. • Avoid steep uphill grades. If the light continues to ﬂash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. Turn the key off, wait at least 10 seconds, and restart the engine.
Page 156: Oil Pressure Light
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: •...
Page 157: Security Light
This indicates that the engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem. Have it ﬁxed immediately. This light comes on brieﬂy while turning on the ignition as a check to show it is working. If it does not come on with the ignition on, there may be a problem with the bulb.
Page 158: Fuel Gage
Fuel Gage United States The fuel gage shows how much fuel the vehicle has left, when the ignition is on. When the indicator nears empty, a LOW FUEL message appears on the Driver Information Center (DIC). See DIC Warnings and Messages on page 3-44 for more information.
Page 159: Auto Stop Mode
Auto Stop Mode United States The AUTO STOP indicator on the tachometer shows that the engine is stopped and is in the fuel saving mode. When the ignition key is turned off, the tachometer needle drops to the OFF indicator. If the ignition is on, the vehicle is in AUTO STOP, and the driver’s door is opened, a chime sounds.
Page 160: Fuel Economy Light
Fuel Economy Light If enabled, this light comes on brieﬂy when the vehicle is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off. This light comes on to indicate the vehicle is achieving fuel economy at or greater than its rated fuel economy.
Page 161: Dic Operation And Displays
Press and hold the information and reset buttons at the same time for one second, then release the buttons to enter the personalization menu. See DIC Vehicle Personalization on page 3-48 for more information. DIC Operation and Displays The DIC comes on when the ignition is on. The DIC has different modes which can be accessed by pressing the DIC buttons.
Page 162 FUEL RANGE Press the information button until FUEL RANGE displays. This mode shows the remaining distance you can drive without refueling in either miles (mi) or kilometers (km). It is based on fuel economy and the fuel remaining in the tank. When the fuel level is low, FUEL RANGE LOW displays.
Page 163: Tire Pressure
OIL LIFE Press the information button until OIL LIFE displays. The engine oil life system shows an estimate of the oil’s remaining useful life. It shows 100% when the system is reset after an oil change. It alerts you to change the oil on a schedule consistent with your driving conditions.
Page 164: Brake Fluid
DIC Warnings and Messages These messages appear if there is a problem detected in one of your vehicle’s systems. A message clears when the vehicle’s condition is no longer present. To acknowledge a message and clear it from the display, press and hold any of the DIC buttons. If the condition is still present, the warning message comes back on the next time the vehicle is turned off and back on.
Page 165: Door Ajar
If a tire pressure message appears on the DIC, stop as soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 5-42, Loading the Vehicle on page 4-22, and Inﬂation - Tire Pressure on page 5-48.
Page 166: Power Steering
ESC (Electronic Stability Control) OFF If your vehicle has Electronic Stability Control (ESC), this message displays and the ESC/TCS light on the instrument panel cluster comes on solid when ESC is turned off. Adjust your driving accordingly. See Electronic Stability Control (ESC) on page 4-6 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-32 for more information.
Page 167: Electronic Stability Control
PUSH PARK PEDAL This message displays if the parking brake is left engaged. See Parking Brake on page 2-29 for more information. SERVICE AIR BAG This message displays when there is a problem with the airbag system. Have your vehicle serviced by your dealer/retailer immediately.
Page 168: Dic Vehicle Personalization
SVC (Service) TIRE MONITOR On vehicles with the Tire Pressure Monitor System (TPMS), this message displays if a part on the TPMS is not working properly. The tire pressure light also ﬂashes and then remains on during the same ignition cycle.
Page 169: Personalization Menu Modes
3. Press the information button to scroll through the available personalization menu modes. Press the reset button to scroll through the available settings for each mode. If you do not make a selection within ten seconds, the display will go back to the previous information displayed.
Page 170: Unlock Horn
UNLOCK HORN This feature, which allows the vehicle’s horn to chirp on the ﬁrst press of the unlock button on the Remote Keyless Entry (RKE) transmitter, can be enabled or disabled. When UNLOCK HORN appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF (default): The horn will not chirp when the unlock button on the RKE transmitter is pressed.
Page 171: Delay Lock
DELAY LOCK This feature, which delays the actual locking of the vehicle, can be enabled or disabled. When DELAY LOCK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ON (default): The doors will not lock until ﬁve seconds after the last door is closed.
Page 172 UNLK (Unlock) This screen displays only if DRIVER or ALL is selected for the AUTO UNLK feature. This feature determines when the automatic door unlocking will occur. When UNLK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: KEY OFF: The door(s) will unlock when the key is turned off.
Page 173 LANGUAGE This feature allows you to select the language in which the DIC will display. When LANGUAGE appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default): All messages will appear in English.
Page 174: Audio System(S)
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 175: Setting The Clock
Setting the Clock To set the time and date: 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press to turn the radio on. 2. Press and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays. 3.
Page 176: Radio(S)
Radio(s) Radio with CD (MP3) and USB Port shown, Radio with CD (MP3) similar The vehicle has one of these radios as its audio system. Radio Data System (RDS) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information.
Page 177: Finding A Station
Finding a Station BAND: Press to choose between FM, AM, or XM™. (Tune): Turn to select radio stations. © SEEK: Press to seek or scan stations with a strong signal in the selected band. • To seek stations, press and release to the previous station and stay there.
Page 178: Storing A Radio Station
Storing a Radio Station Drivers are encouraged to set up radio station favorites while the vehicle is in P (Park). Tune to favorite stations using the softkeys, favorites button, and steering wheel controls. See Defensive Driving on page 4-2. FAV (Favorites): A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio favorites page button (FAV button).
Page 179: Adjusting The Speakers (Balance/Fade)
Setting the Tone (Bass/Midrange/Treble) BASS/MID/TREB (Bass, Midrange, or Treble): The radio may display some or all tones such as BASS, MID, and TREB. To adjust the tone settings: 1. Press until the tone control tabs display. 2. Press the softkey below the desired tab, then turn to adjust the highlighted setting.
Page 180: Radio Messages
Finding a Category (CAT) Station (XM Satellite Radio Service Only) CAT (Category): The radio may have the CAT button feature. To select and ﬁnd a desired category: 1. Press BAND until the XM frequency displays. 2. Press CAT to display the category labels on the radio display.
Page 181: Loading A Cd
XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in the vehicle.
Page 182 FWD (Fast Forward): Press and hold to advance playback quickly within a track. Sound is heard at a reduced volume and the elapsed time of the track displays. Release to resume playing the track. RDM (Random): Tracks can be listened to in random, rather than sequential order.
Page 183: Care Of Cds
If any error occurs repeatedly or if an error cannot be corrected, contact your dealer/retailer. If the radio displays an error message, write it down and provide it to your dealer/retailer when reporting the problem. Care of CDs Store CD(s) in their original cases or other protective cases and away from direct sunlight and dust.
Page 184: Using The Usb Port
To use a portable audio player, connect a 3.5 mm (1/8 inch) cable to the radio’s front auxiliary input jack. When a device is connected, press the radio CD/AUX button to begin playing audio from the device over the vehicle speakers. (Power/Volume): Turn to adjust the volume.
Page 185: Using An Mp3
Using an MP3 Format Radios that have the capability of playing MP3’s can play .mp3 ﬁles that were recorded onto a CD-R or CD-RW disc. Radios that have a USB port can play .mp3 and .wma ﬁles that are stored on a USB storage device as well as AAC ﬁles that are stored on an iPod Compressed Audio The radio can play discs that contain both uncompressed...
Page 186 Order of Play Tracks are played in the following order: • Play begins from the ﬁrst track in the ﬁrst playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the ﬁrst track of the ﬁrst playlist.
Page 187 FWD (Fast Forward): Press and hold to advance playback quickly. Sound is heard at a reduced volume and the elapsed time of the ﬁle displays. Release FWD to resume playing. The elapsed time of the ﬁle displays. (Previous Folder): Press the softkey below to go to the ﬁrst track in the previous folder.
Page 188: Connecting A Usb Storage Device ® Or Ipod
Connecting a USB Storage Device ® or iPod The USB Port can be used to control an iPod or a USB storage device. To connect a USB storage device, connect the device to the USB port located on the front of the radio. To connect an iPod, connect one end of the USB cable that came with the iPod to the iPod’s dock connector and connect the other end to the USB port located...
Page 189: Using Softkeys To Control A Usb Storage Device Or Ipod
Using Softkeys to Control a USB Storage Device or iPod The ﬁve softkeys below the radio display are used to control the functions listed below. To use the softkeys: 1. Press the ﬁrst or ﬁfth softkey below the radio display to display the functions listed below, or press the softkey below the function if it is currently displayed.
Page 190 To select ﬁles: 1. Press the softkey below 2. Turn to scroll through the list of menus. 3. Press to select the desired menu. 4. Turn to scroll through the folders or ﬁles in the selected menu. 5. Press to select the desired ﬁle to be played. To skip through large lists, the ﬁve softkeys can be used to navigate in the following order: •...
Page 191: Xm Radio Messages
XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds.
Page 192: Bluetooth
Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault.
Page 193: Pairing A Phone
Pairing A Bluetooth enabled cell phone must be paired to the in-vehicle Bluetooth system ﬁrst and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar Calling, if available.
Page 194: Storing Name Tags
Listing All Paired and Connected Phones 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices.
Page 195 Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Store”. The system responds with “Store, number please”...
Page 196: Deleting Name Tags
4. After the complete number has been entered, say “Store”. The system responds with “Please say the name tag” followed by a tone. 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store <name tag>.
Page 197: Making A Call
Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar, if present. To use the delete all name tags command: 1. Press and hold for two seconds.
Page 198: Using The Call Command
4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds with “OK, Dialing” and dials the number. • If an unwanted number is recognized by the system, say “Clear”...
Page 199: Call Waiting
Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. • Press to answer an incoming call when another call is active. The original call is placed on hold. • Press again to return to the original call.
Page 200: Transferring A Call
Transferring a Call Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press . The system responds with “Ready” followed by a tone.
Page 201 Sending a Number During a Call 1. Press . The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Say a number to send tones” followed by a tone. 3. Say the number to send. •...
Page 202: Other Information
Other Information ® The Bluetooth word mark and logos are owned by the ® Bluetooth SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. This device complies with Part 15 of the FCC Rules.
Page 203 To change radio stations: • Press and release to go to the next or previous radio station stored as a preset. • Press and hold to go to the next or previous radio station in the selected band with a strong signal.
Page 204: Radio Reception
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Page 205: Backglass Antenna
Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception.
Page 206 ✍ NOTES 3-86...
Page 207: Driving Your Vehicle
Section 4 Your Driving, the Road, and the Vehicle ...4-2 Driving for Better Fuel Economy ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-3 Control of a Vehicle ...4-3 Braking ...4-4 Antilock Brake System (ABS) ...4-5 Braking in Emergencies ...4-5 Electronic Stability Control (ESC) ...4-6 Traction Control System (TCS) ...4-8 Steering ...4-11 Off-Road Recovery ...4-13...
Page 208: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops. •...
Page 209: Drunk Driving
Drunk Driving CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking.
Page 210: Braking
Braking See Brake System Warning Light on page 3-30. Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second.
Page 211: Antilock Brake System (Abs)
Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that will help prevent a braking skid. When the engine is started and the vehicle begins to drive away, ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little.
Page 212: Electronic Stability Control (Esc)
Brake Assist This vehicle has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle.
Page 213 This light will ﬂash on the instrument panel cluster when the ESC system is both on and activated. The system may be heard or felt while it is working; this is normal. When the light is on solid and either the SERVICE ESC or ESC OFF message is displayed, the system will not assist the driver in maintaining directional control of the vehicle.
Page 214: Traction Control System (Tcs)
It is recommended to leave the system on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow, and you want to “rock” the vehicle to attempt to free it.
Page 215 If the vehicle is in cruise control when TCS begins to limit wheel spin, the cruise control will automatically disengage. The cruise control may be re-engaged when road conditions allow. See Cruise Control on page 3-10. When this light is on solid and either the SERVICE TRACTION or TRACTION OFF message is displayed,...
Page 216: Traction Control Operation
Traction Control Operation Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary. The traction control system is enabled automatically when the vehicle is started, and it will activate and ﬂash the ESC/TCS light and display the LOW TRACTION message if it senses either of the front wheels are spinning or beginning to lose traction while driving.
Page 217: Steering
Steering If the engine stalls while driving, the power steering assist system will continue to operate until you are able to stop the vehicle. If power steering assist is lost because the electric power steering system is not functioning, the vehicle can be steered but it will take more effort.
Page 218: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 219: Off-Road Recovery
Off-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Page 220 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Page 221: Driving At Night
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive. •...
Page 222: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or ﬂowing water. CAUTION: Wet brakes can cause crashes.
Page 223: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 224: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 225: Winter Driving
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand.
Page 226 Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 7-7. To get help and keep everyone in the vehicle safe: •...
Page 227: If Your Vehicle Is Stuck In Sand, Mud, Ice
Run the engine for short periods only as needed to keep warm, but be careful. To save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold.
Page 228: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible. To prevent transmission wear, wait until the wheels stop spinning before shifting gears.
Page 229 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The Tire and Loading Information label lists the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms...
Page 230 Steps for Determining Correct Load Limit Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 231 Example 1 Item Description Maximum Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) × 2 = Available Occupant and Cargo Weight = Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Maximum Vehicle...
Page 232 Example 3 Item Description Maximum Vehicle Capacity Weight for Example 3 = Subtract Occupant Weight 200 lbs (91 kg) × 5 = Available Cargo Weight = Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s maximum vehicle capacity weight 4-26 and seating positions.
Page 233 Never exceed the GVWR for your vehicle or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. CAUTION: Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
Page 234: Towing
Towing Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 7-7. To tow the vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing”...
Page 235: Dinghy Towing
Dinghy Towing When dinghy towing, the vehicle should be run at the beginning of each day and at each RV fuel stop for about ﬁve minutes. This will ensure proper lubrication of transmission components. To dinghy tow the vehicle from the front with all four wheels on the ground: 1.
Page 236: Dolly Towing
Notice: Towing the vehicle from the rear could damage it. Also, repairs would not be covered by the warranty. Never have the vehicle towed from the rear. 4-30 Dolly Towing Tow the vehicle with the two rear wheels on the ground and the front wheels on a dolly.
Page 237: Towing A Trailer
To tow the vehicle with two wheels on the ground and a dolly: 1. Put the front wheels on a dolly. 2. Put the gear shift lever in P (Park). 3. Set the parking brake. 4. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing.
Page 238 ✍ NOTES 4-32...
Page 239: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of the Vehicle ...5-5 Fuel ...5-6 Gasoline Octane ...5-6 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-7 Fuels in Foreign Countries ...5-8...
Page 240 Section 5 Tire Inspection and Rotation ...5-54 When It Is Time for New Tires ...5-56 Buying New Tires ...5-56 Different Size Tires and Wheels ...5-58 Uniform Tire Quality Grading ...5-59 Wheel Alignment and Tire Balance ...5-60 Wheel Replacement ...5-61 Tire Chains ...5-63 If a Tire Goes Flat ...5-64 Tire Sealant and Compressor Kit ...5-65 Tire Sealant and Compressor Kit Storage ...5-73...
Page 241: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine Saturn parts and Saturn-trained and supported service people. Genuine Saturn parts have one of these marks. Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and...
Page 242: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 243: Adding Equipment To The Outside Of The Vehicle
CAUTION: You can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. • Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.
Page 244: Fuel
Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. To help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Gasoline Octane Use regular unleaded gasoline with a posted octane rating of 87 or higher.
Page 245: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S.
Page 246: Fuels In Foreign Countries
Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to ﬁnd. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty.
Page 247 The fuel door is located on the passenger side of the vehicle. To open the fuel door, push the rearward center edge in and release and it will open. To remove the tethered fuel cap, turn it slowly counterclockwise.
Page 248 While refueling, hang the tethered fuel cap from the hook on the fuel door. CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather.
Page 249: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs.
Page 250: Checking Things Under The Hood
Checking Things Under the Hood CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Things that burn can get on hot engine parts and start a ﬁre.
Page 251 2. Then go to the front of the vehicle and push the secondary hood release handle toward the driver side of the vehicle. 3. Lift the hood. 4. After the hood is slightly lifted, it will continue to open to the full position. Before closing the hood, be sure all the ﬁller caps are on properly.
Page 252: Engine Compartment Overview
Engine Compartment Overview When you open the hood, this is what you see: 5-14...
Page 253: Engine Oil
A. Engine Air Cleaner/Filter. See Engine Air Cleaner/Filter on page 5-20. B. Cooling Fans (Out of view). See Cooling System on page 5-22. C. Engine Oil Dipstick. See “Checking Engine Oil” under Engine Oil on page 5-15. D. Engine Oil Fill Cap. See “When to Add Engine Oil” under Engine Oil on page 5-15.
Page 254: When To Add Engine Oil
When to Add Engine Oil If the oil is below the MIN (minimum) mark, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-92.
Page 255: Cold Temperature Operation
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Page 256: Engine Oil Life System
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system ﬂushes are not recommended and could cause engine damage not covered by the vehicle warranty.
Page 257: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE OIL SOON message being turned on, reset the system.
Page 258: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-14 for the location of the engine air cleaner/ﬁlter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (80 000 km) interval.
Page 259 3. Inspect or replace the engine air cleaner/ﬁlter. 4. Align the ﬁlter correctly using the alignment tab. 5. Install the cover by guiding the tabs on the rim of the top cover into the bottom hinges and turn the cover down to close it. 6.
Page 260: Automatic Transmission Fluid
Automatic Transmission Fluid It is not necessary to check the transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take your vehicle to the dealer/retailer and have it repaired as soon as possible. Change the ﬂuid and ﬁlter at the intervals listed in Additional Required Services on page 6-6, and be sure to use the transmission ﬂuid listed in Recommended...
Page 261: Engine Coolant
CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
Page 262: What To Use
What to Use CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning.
Page 263: Checking Coolant
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL...
Page 264: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
Page 265: Pressure Cap
3. Fill the coolant surge tank with the proper mixture, to the FULL COLD mark. Wait about ﬁve minutes, then check to see if the level is below the mark. If the level is below the FULL COLD mark, add additional coolant to bring the level up to the mark.
Page 266: Engine Overheating
Engine Overheating The vehicle has an indicator to warn of engine overheating. There is an engine coolant temperature warning light on the vehicle’s instrument panel. See Engine Coolant Temperature Warning Light on page 3-33 for more information. You may decide not to lift the hood when this warning appears, but instead get service help right away.
Page 267: If No Steam Is Coming From The Engine Compartment
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: •...
Page 268: Windshield Washer Fluid
Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing.
Page 269: Brakes
Brakes This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal ﬁrmly.
Page 270: Battery
Battery CAUTION: Batteries have acid that can burn you and gas that can explode. You can be badly hurt if you are not careful. See Jump Starting on page 5-33 for tips on working around a battery without getting hurt. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause...
Page 271: Jump Starting
Jump Starting If the battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 272 Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle.
Page 273 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 274 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one.
Page 275: Headlamp Aiming
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 276: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-40. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 277 To replace a sidemarker lamp, turn signal lamp, or a back-up lamp: 1. Open the trunk. See Trunk on page 2-12. 2. Remove the convenience net. 3. Remove the wing nuts holding the trunk trim and pull the trunk trim straight back. 4.
Page 278: License Plate Lamp
License Plate Lamp To replace the license plate lamp bulb: 1. Remove the license plate assembly by turning the two screws counterclockwise. 2. Turn and pull the license plate lamp forward through the fascia opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Page 279: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Inspect the windshield wiper blades for wear or cracking. See Scheduled Maintenance on page 6-4. To remove the wiper blade: 1. Pull the windshield wiper arm connector away from the windshield. 2. Push the release button. 3.
Page 280: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. CAUTION: Poorly maintained and improperly used tires are dangerous.
Page 281: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The example below shows a typical passenger (p-metric) tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 282 (F) Uniform Tire Quality Grading (UTQG) manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance. For more information see Uniform Tire Quality Grading on page 5-59. (G) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load.
Page 283: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight This means the combined weight of optional accessories.
Page 284 Intended Outboard Sidewall asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) The metric unit for air pressure. Light Truck (LT-Metric) Tire light duty trucks and some multipurpose passenger vehicles. Load Index An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.
Page 285 Radial Ply Tire A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. A metal support for a tire and upon which the tire beads are seated. Sidewall The portion of a tire between the tread and the bead.
Page 286: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 287: How To Check
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 288: Tire Pressure Monitor System
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inﬂated to the inﬂation pressure recommended by the vehicle manufacturer...
Page 289: Tire Pressure Monitor Operation
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Page 290: Tpms Malfunction Light And Message
The low tire pressure warning light may come on in cool weather when the vehicle is ﬁrst started, and then turn off as you start to drive. This could be an early indicator that the air pressure in the tire(s) are getting low and need to be inﬂated to the proper pressure.
Page 291: Tpms Sensor Matching Process
• Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels. Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly. See Buying New Tires on page 5-56. • Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.
Page 292: Tire Inspection And Rotation
6. The passenger side front turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side front tire and repeat the procedure in Step 5. 7. The passenger side rear turn signal comes on to indicate that corner sensor is ready to be learned.
Page 293 When rotating the vehicle’s tires, always use the correct rotation pattern shown here. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-48 and Loading the Vehicle on page 4-22.
Page 294: When It Is Time For New Tires
When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions inﬂuence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch...
Page 295 GM’s exclusive TPC Spec system considers over a dozen critical speciﬁcations that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM’s TPC Spec number is molded onto the tire’s sidewall near the tire size.
Page 296: Different Size Tires And Wheels
You may increase the chance that you will crash and suffer serious injury. Only use Saturn speciﬁc wheel and tire systems developed for your vehicle, and have them properly installed by a Saturn certiﬁed technician.
Page 297: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance.
Page 298: Wheel Alignment And Tire Balance
Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on speciﬁed government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Page 299: Wheel Replacement
If you need to replace any of your wheels, wheel bolts, or wheel nuts, replace them only with new Saturn original equipment parts. This way, you will be sure to have the right wheel, wheel bolts, and wheel nuts for your vehicle.
Page 300 This could lead to a crash. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new Saturn original equipment wheel nuts. Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage.
Page 301: Tire Chains
You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new Saturn original equipment wheel. Tire Chains CAUTION: Do not use tire chains.
Page 302: If A Tire Goes Flat
If a Tire Goes Flat Your vehicle has a tire sealant and compressor kit. See Tire Sealant and Compressor Kit on page 5-65. There is no spare tire, no tire changing equipment, and no place to store a tire. It is unusual for a tire to blow out while you are driving, especially if you maintain your tires properly.
Page 303 Tire Sealant and Compressor Kit CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation.
Page 304: Tire Sealant
Read and follow all of the tire sealant and compressor kit instructions. The kit includes: A. Air Compressor E. Pressure Gage B. Tire Sealant F. Air Only Hose Canister (Black) C. Power Plug G. Sealant/Air Hose D. On/Off Button (Clear) 5-66 Tire Sealant Read and follow the safe handling instructions on the...
Page 305: Punctured Tire
Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inﬂate a Punctured Tire When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes. This will help to inﬂate the tire faster. Always do a safety check ﬁrst.
Page 306 7. Start the vehicle. The vehicle must be running while using the air compressor. 8. Press the on/off (D) button to turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gage (E) will initially show a high pressure while the compressor pushes the sealant into the tire.
Page 307 15. If the ﬂat tire was able to inﬂate to the recommended inﬂation pressure, remove the maximum speed label from the sealant canister (B) and place it in a highly visible location. The label is a reminder not to exceed 55 mph (90 km/h) until the damaged tire is repaired or replaced.
Page 308: Not Punctured
Using the Tire Sealant and Compressor Kit without Sealant to Inﬂate a Tire (Not Punctured) To use the air compressor to inﬂate a tire with air only and not sealant: Always do a safety check ﬁrst. See If a Tire Goes Flat on page 5-64.
Page 309 8. Plug the power plug (C) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Accessory Power Outlet(s) on page 3-18. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter.
Page 310: Removal And Installation Of The Sealant Canister
Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unlock the air only hose (F) from the sealant canister (B) by pulling up on the lever. 2. Pull the air only hose (F) from the sealant canister (B).
Page 311 To install a new sealant canister: 1. Align the sealant/air hose (F) with the slot in the air compressor. 2. Push the sealant canister (B) down and turn it clockwise. 3. Wrap the sealant/air hose (F) around the air compressor channel to stow it in its original location. 4.
Page 312: Appearance Care
Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from the upholstery.
Page 313: Fabric/Carpet
• Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide. Use only mild, neutral-pH soaps. • Too much cleaner that saturates the upholstery. •...
Page 314: Instrument Panel, Vinyl, And Other Plastic Surfaces
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary, a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt. Never use spot lifters or removers on plastic surfaces.
Page 315: Washing Your Vehicle
Washing Your Vehicle The best way to preserve the vehicle’s ﬁnish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label. If it states that it should not be used on plastic parts, do not use it on the vehicle or damage may occur and it would not be covered by the warranty.
Page 316: Windshield And Wiper Blades
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage the vehicle’s ﬁnish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter.
Page 317: Aluminum Wheels
Aluminum Wheels Notice: Chrome wheels and other chrome trim may be damaged if the vehicle is not washed after driving on roads that have been sprayed with magnesium, calcium or sodium chloride. These chlorides are used on roads for conditions such as ice and dust.
Page 318: Sheet Metal Damage
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.
Page 319: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Vehicle Certiﬁcation and Service Parts labels and the certiﬁcates of title and registration.
Page 320: Electrical System
Electrical System Intermediate Voltage Devices and Wiring CAUTION: Exposure to intermediate voltage can cause shock and burns. The intermediate voltage systems in the vehicle can only be serviced by technicians with special training. Intermediate voltage devices are identiﬁed by labels. Do not remove, open, take apart, or modify these devices.
Page 321: Power Windows And Other Power Options
Power Windows and Other Power Options Fuses in the fuse block protect the power windows. When the current load is too heavy, the fuse opens protecting the circuit until the problem is ﬁxed. Fuses The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible links.
Page 322 Your vehicle might not have all the fuses and features listed. 5-84...
Page 323 Fuses Usage POWER Power Mirrors MIRRORS Electronic Power Steering Cruise Control Switch, Passenger RUN/CRANK Airbag Status Indicator HVAC Heating Ventilation Air Conditioning BLOWER HIGH Blower - High Speed Relay CLUSTER/ Instrument Panel Cluster, Theft THEFT Deterrent System ® ONSTAR OnStar Not Used INSTALLED AIRBAG (IGN) Airbag (Ignition)
Page 324: Engine Compartment Fuse Block
Fuses ROOF/HEAT Sunroof, Heated Seat SEAT Not Used INSTALLED Not Used INSTALLED AIRBAG Airbag (Battery) (BATT) SPARE FUSE Spare Fuse Holder HOLDER SPARE FUSE Spare Fuse Holder HOLDER SPARE FUSE Spare Fuse Holder HOLDER SPARE FUSE Spare Fuse Holder HOLDER FUSE PULLER Fuse Puller 5-86 Engine Compartment Fuse Block...
Page 325 Fuses Usage Air Conditioner Clutch Electronic Throttle Control Belt Alternator Starter (BAS) IGN Fuses Usage Transmission, Transmission Control Module Ignition 1 Belt Alternator Starter (BAS) Pumps 5-87...
Page 326 Fuses Emission Left Headlamp Low-Beam Horn Right Headlamp Low-Beam Left Headlamp High-Beam Right Headlamp High-Beam Engine Control Module BATT Windshield Wiper Antilock Brake System (ABS) (IGN 1) Engine Control Module (IGN 1) Cooling Fan 1 Cooling Fan 2 Run Relay, Heating, Ventilation, Air Conditioning Blower Body Control Module 1 Body Control Module Run/Crank...
Page 327: Rear Compartment Fuse Block
Relays Usage Air Conditioning Clutch High-Beam Headlamp Horn Low-Beam Headlamp Windshield Wiper 1 Windshield Wiper 2 Daytime Running Lamps (DRL) Stoplamps Transmission Pump Motor Diodes Usage Wiper Rear Compartment Fuse Block The rear compartment fuse block is located in the trunk of the vehicle.
Page 328 Fuses Passenger Seat Controls Driver Seat Controls Not Used Not Used 5-90 Usage Fuses Usage Emission 2, Canister Vent Solenoid Park Lamps, Instrument Panel Dimming Not Used...
Page 329 Fuses Usage Not Used Not Used Sunroof Controls Not Used Not Used Audio Ampliﬁer Heated Seat Controls Not Used Remote Keyless Entry (RKE) System, XM™ Satellite Radio, UGDO Back-up Lamps Not Used Not Used Auxiliary Power Outlets Not Used Trunk Release Rear Defog Fuses Usage...
Page 330: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Please refer to Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant R134a Cooling System Transmission (Bottom Pan Removal) Engine Oil with Filter Fuel Tank Wheel Nut Torque All capacities are approximate.
Page 331 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-12...
Page 332: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and lubricants as prescribed in this manual are necessary to keep this vehicle in good working condition.
Page 333 CAUTION: Performing maintenance work on a vehicle can be dangerous. In trying to do some jobs, you can be seriously injured. Do your own maintenance work only if you have the required know-how and the proper tools and equipment for the job. If you have any doubt, see your dealer/retailer to have a qualiﬁed technician do the work.
Page 334: Scheduled Maintenance
Scheduled Maintenance When the CHANGE OIL SOON message displays in the Driver Information Center (DIC), service is required for the vehicle. Have the vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 335 Change engine oil and ﬁlter. See Engine Oil on page 5-15. Reset oil life system. See Engine Oil Life System on page 5-18. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter. See Engine Air Cleaner/Filter on page 5-20.
Page 336: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 337: Maintenance Footnotes
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts or signs of wear.
Page 338: Engine Oil Level Check
(h) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 339: At Least Once A Month
Engine Coolant Level Check Check the engine coolant level and add DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-23. Windshield Washer Fluid Level Check Check the windshield washer ﬂuid level in the windshield washer ﬂuid reservoir and add the proper ﬂuid if necessary.
Page 340: Ignition Transmission Lock Check
Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface.
Page 341: Underbody Flushing Service
Parking Brake and Automatic Transmission P (Park) Mechanism Check CAUTION: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Page 342: Recommended Fluids And Lubricants
Tire Sealant and Compressor Kit Check the sealant expiration date printed on the instruction label of the Tire Sealant and Compressor Kit at least once a year. See your dealer/retailer for a replacement canister. Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer.
Page 343: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter Engine Oil Filter Spark Plugs Wiper Blades Driver Side – 23.6 in (60.0 cm) Passenger Side – 21.0 in (53.0 cm) Part Numbers ACDelco Part Numbers 22676970...
Page 344: Engine Drive Belt Routing
Engine Drive Belt Routing The engine drive belt on this hybrid vehicle is under a higher tension than the engine drive belt on a non-hybrid vehicle and requires the use of a special kind of tool to service. See your dealer/retailer for service. 6-14...
Page 345: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 346 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 347 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 348 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 349: Customer Assistance Information
Reporting Safety Defects ...7-14 Reporting Safety Defects to the United States Government ...7-14 Reporting Safety Defects to the Canadian Government ...7-14 Reporting Safety Defects to Saturn ...7-14 Service Publications Ordering Information ...7-15 Vehicle Data Recording and Privacy ...7-16 Event Data Recorders ...7-16 ®...
Page 350: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your retailer and to Saturn. Together we are committed to providing our customers with unparalleled service, before, during, and after the purchase of a Saturn vehicle, for total customer satisfaction. We call this the Saturn Difference.
Page 351 Saturn vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, Saturn and its retailers offer the additional assistance of a neutral party through our voluntary participation in a mediation/arbitration program called Better Business Bureau (BBB) Auto Line.
Page 352 For further information concerning eligibility in the Canadian Motor Vehicle Arbitration Plan (CAMVAP), call toll-free 1-800-207-0685. Alternatively, you may call the Saturn Customer Communication Centre, 1-800-263-1999, or you may write to: Mediation/Arbitration Program c/o Customer Communication Centre...
Page 353: Online Owner Center
— all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Saturn retailers for service nationwide • Exclusive privileges and offers • Recall notices for your speciﬁc vehicle • ®...
Page 354: Customer Assistance For Text Telephone (Tty) Users
Customer Assistance for Text Telephone (TTY) Users To assist owners who have hearing difficulties, Saturn has installed special TDD (Telecommunication Devices for the Deaf) equipment in its Saturn Customer Assistance Center. Any hearing or speech-impaired customer who has access to a TDD or to a conventional Text Telephone (TTY) can communicate with Saturn by dialing 1-800-TDD-6000.
Page 355: Roadside Assistance Program
For more details, or to determine your vehicle’s eligibility, visit your Saturn retailer or call the Saturn Customer Assistance Center at 1-800-553-6000. Text telephone (TTY) users, call 1-800-833-6000. In Canada, customers may call the Saturn Customer Communication Centre at 1-800-263-1999. TTY users in Canada may call 1-800-263-3830.
Page 356: Services Provided
• Emergency Tow From a Public Road or Highway: Tow to the nearest Saturn retailer for warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given when the vehicle is stuck in sand, mud, or snow.
Page 357: Scheduling Service Appointments
• Trip Interruption Beneﬁts and Assistance: Must be over 250 kilometres from where your trip was started to qualify. General Motors of Canada Limited requires pre-authorization, original detailed receipts, and a copy of the repair orders. Once authorization has been received, the Roadside Assistance advisor will help you make arrangements and explain how to receive payment.
Page 358: Transportation Options
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, Saturn helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your retailer can offer you one of the following:...
Page 359: Collision Damage Repair
All Courtesy Transportation arrangements will be administered by appropriate retailer personnel. Saturn reserves the right to unilaterally modify, change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described herein at its sole discretion.
Page 360: Repair Facility
Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
Page 361 • Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identiﬁcation Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle.
Page 362: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your retailer or Saturn Corporation. To contact NHTSA, call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153);...
Page 363: Service Manuals
Service Publications Ordering Information Service Manuals A variety of publications are available to you. Saturn service manuals are written for trained technicians, and in some cases, specialized tools and equipment are necessary to complete certain repairs. However, the manuals are available to owners who either have the training, or wish to gain a greater understanding of the technical aspect of their Saturn.
Page 364: Vehicle Data Recording And Privacy
Vehicle Data Recording and Privacy Your Saturn vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance,...
Page 365: Onstar
EDR. Saturn will not access this data or share it with others except: with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee; in response to an official request of police or similar government office;...
Page 366 ✍ NOTES 7-18...
Page 367 Accessories and Modiﬁcations ... 5-3 Accessory Power Outlets ... 3-18 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-71 Additives, Fuel ... 5-7 Add-On Electrical Equipment ... 5-82 Air Cleaner/Filter, Engine ... 5-20 Air Conditioning ... 3-19 Airbag Passenger Status Indicator ... 3-29 Readiness Light ...
Page 368 Automatic Transmission Fluid ... 5-22 Operation ... 2-27 Backglass Antenna ... 3-85 Battery ... 5-32 Electric Power Management ... 3-16 Run-Down Protection ... 3-17 ® Bluetooth ... 3-72 Brake Emergencies ... 4-5 Brake Fluid ... 5-31 Brakes ... 5-31 Regenerative Braking ... 2-30 System Warning Light ...
Page 369 Users ... 7-6 Customer Assistance Offices ... 7-6 Customer Satisfaction Procedure ... 7-2 GM Mobility Reimbursement Program ... 7-6 Reporting Safety Defects to Saturn ... 7-14 Reporting Safety Defects to the Canadian Government ... 7-14 Reporting Safety Defects to the United States Government ...
Page 370 Door (cont.) Locks ... 2-9 Power Door Locks ... 2-9 Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... 2-11 Driver Information Center (DIC) ... 3-40 DIC Operation and Displays ... 3-41 DIC Vehicle Personalization ... 3-48 DIC Warnings and Messages ... 3-44 Driving At Night ...
Page 371 Filter Engine Air Cleaner ... 5-20 Finish Damage ... 5-80 Flashers, Hazard Warning ... 3-6 Flash-to-Pass ... 3-8 Flat Tire ... 5-64 Fluid Automatic Transmission ... 5-22 Windshield Washer ... 5-30 Folding Rear Seat ... 1-9 Fuel ... 5-6 Additives ... 5-7 California Fuel ...
Page 372 Headlamps Off in Park ... 3-14 Heated Seats ... 1-4 Heater ... 3-19 Engine Coolant ... 2-26 Highbeam On Light ... 3-37 High-Speed Operation, Tires ... 5-49 Highway Hypnosis ... 4-17 Hill and Mountain Roads ... 4-18 Hood Checking Things Under ... 5-12 Release ...
Page 373 Light (cont.) Brake System Warning ... 3-30 Charging System ... 3-30 Cruise Control ... 3-37 Engine Coolant Temperature Warning ... 3-33 Fuel Economy ... 3-40 Highbeam On ... 3-37 Oil Pressure ... 3-36 Passenger Airbag Status Indicator ... 3-29 Safety Belt Reminders ... 3-27 Security ...
Page 374 Mirrors Manual Rearview Mirror ... 2-35 Outside Automatic Dimming Mirror ... 2-36 Outside Power Mirrors ... 2-35 MP3 ... 3-65 MyGMLink.com ... 7-5 Navigation System, Privacy ... 7-17 New Vehicle Break-In ... 2-21 Odometer ... 3-26 Odometer, Trip ... 3-26 Off-Road Recovery ...
Page 375 Remote Vehicle Start ... 2-7 Replacement Bulbs ... 5-40 Replacement Parts, Maintenance ... 6-13 Reporting Safety Defects Canadian Government ... 7-14 Saturn ... 7-14 United States Government ... 7-14 Restraint System Check Checking the Restraint Systems ... 1-72 Replacing Restraint System Parts After a Crash ...
Page 376 Scheduled Maintenance ... 6-4 Seats Head Restraints ... 1-8 Heated Seats ... 1-4 Manual Lumbar ... 1-4 Power Lift Seat ... 1-9 Power Seats ... 1-3 Reclining Seatbacks ... 1-5 Split Folding Rear Seat ... 1-9 Securing a Child Restraint Rear Seat Position ...
Page 377 Theft-Deterrent Systems (cont.) ® PASS-Key III+ Electronic Immobilizer Operation ... 2-19 Tilt Wheel ... 3-6 Time, Setting ... 3-55 Tire Pressure Light ... 3-33 Tire Sealant Storing ... 5-73 Tires ... 5-42 Aluminum Wheels, Cleaning ... 5-79 Buying New Tires ... 5-56 Chains ...
Page 378 Vehicle Data Recording and Privacy ... 7-16 Vehicle Identiﬁcation Number (VIN) ... 5-81 Service Parts Identiﬁcation Label ... 5-81 Vehicle Personalization DIC ... 3-48 Vehicle, Remote Start ... 2-7 Ventilation Adjustment ... 3-24 Visors ... 2-17 Warning Lights, Gages, and Indicators ... 3-24 Warnings DIC Warnings and Messages ...

Saturn 2009 Aura Green Line Hybrid Owner's Manual

Section 1 Seats and Restraint System

Seats and Restraint System

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Saturn 2009 Aura Green Line Hybrid

Summary of Contents for Saturn 2009 Aura Green Line Hybrid