Saris 911 Instructions

Upright mount bicycle carrier

Advertisement

Quick Links

Step 7-
Close and lock track.
• Turn knob, at end of each load
bar, in direction of orange arrow
until the word "LOCK" appears.
• Lock load bar with key.
Step 8-
Check your installation. Be certain:
• Daisy dials are tightened completely against wheel tray and upright bracket.
Retighten daisy dial against upright bracket after first two hours of initial use.
• Upright clamp is firmly grasping each bike and is in the closed position.
• Wheel straps are used on both front and rear tires.
• Accessory tracks are closed and locked.
• Load is evenly distributed on load bars. For maximum weight limitations,
follow recommendations of vehicle manufacturer.
• The entire system including attachment of load bars to the vehicle is
stable and secure. Walk around vehicle to check each attachment clip.
Refer to attachment clip instructions for correct clip positioning and
proper installation.

Cautions

1) All requirements for compatibility/ fit as stated in the current Saris
Vehicle/ Carrier Compatibility Guide must be followed.
2) Check your installation as recommended. Because vehicles and
conditions vary, it is your responsibility to insure the safe and proper
use of this product. Improper attachment or misuse may result in
damage to your carrier, bicycles, vehicle, or vehicles traveling behind
you.
3) Use only Saris clips and accessories.
4) When in use, remember carrier is installed!
a) Be aware of low overhead clearances.
b) Do not go through automatic car wash with carrier installed.
c) Occasionally check attachment of carrier and load.
5) Open vehicle doors before removing carrier; failure to do so could
damage doors.
6) Replace any part at first sign of fatigue or wear.

Warning and Disclaimer

This carrier has been designed to carry accessories on
specific vehicles. Before installation, user must read and
follow current Vehicle/ Carrier Compatibility Guide (available
through Saris dealer) recommendations and enclosed
instructions. Fit recommendations are based on vehicle's
standard features; optional features may affect the fit
recommendations. User must attach carrier correctly to the
vehicle, check its attachment before each use, and inspect
carrier parts for wear. Carrier's attachment to the vehicle is
critical and beyond the control of the manufacturer.
Manufacturer and seller expressly disclaim any and all
liability for personal injury, property damage or loss, whether
direct, indirect, or incidental, resulting from the incorrect
attachment, improper use, inadequate maintenance, or
neglect of this carrier.

Warranty

We warrant this product to the first consumer to be free from
defect in material and workmanship for a period of two years
from date of purchase. (Please retain your sales slip for
your records.) Any product or part thereof found to be
defective within that period will be replaced without charge
provided that: (1) the product was not misused; (2) no
alterations or modifications were made; (3) its failure
resulted from a defect in material or workmanship and not
from normal wear expected in the use of the product; (4) the
product or part is delivered, freight prepaid, to Graber
Products. Manufacturers only obligation shall be to replace
such products or parts proved to be defective.
a special products division of
5253 Verona Rd.
Madison, WI 53711
Made in U.S.A.
800-783-7257
911-IS 11/99 Revison B
www.sarisproducts.com
UPRIGHT MOUNT
Bicycle Carrier
Please READ and FOLLOW all instructions carefully!
upright arm
tension
screw
channel
The Saris Upright Mount Accessory can support bikes
with a tire size between 12-1/2 and 27 inches.
Step 1-
Check load bar placement.
Use of the upright mount requires that your load bar spacing be between
16" (minimum) and 36" (maximum).
Refer to available load bar spacing in clip set instructions.
If your available load bar spacing is:
- less than or equal to 36 inches, place load bars following all
recommendations in your clip set instructions.
- greater than 36 inches,
place load bars 36" apart
anywhere along the
Worldwide patents
length of your
issued and pending.
vehicle.
Model #911
wheel straps
clamp
handle
upright bracket
wheel tray
lever
attachment block
daisy dials
(tightens to load bar)
(tightens to wheel tray)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 911 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Saris 911

  • Page 1 Refer to attachment clip instructions for correct clip positioning and proper installation. Cautions 1) All requirements for compatibility/ fit as stated in the current Saris Vehicle/ Carrier Compatibility Guide must be followed. 2) Check your installation as recommended. Because vehicles and conditions vary, it is your responsibility to insure the safe and proper use of this product.
  • Page 2 For upright clamp locking capabilities, Lock Plug Kits are available through your local Saris dealer. To complete a single key locking system, purchase the Lock Plug item number identical to the number on your Saris load bar key. Insert Lock Plug per instructions before mounting upright arm to load bar.

Table of Contents