Related Manuals for Sanyo PLC PLC-XP100BKL
Summary of Contents for Sanyo PLC PLC-XP100BKL
- Page 1 Multimedia Projector PLC-XP100L MODEL PLC-XP100BKL Owner’s Manual Projection lens is optional. ✽...
-
Page 2: Features And Design
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD) technology. Functionally Rich ◆ This projector has many useful functions such... -
Page 3: Table Of Contents
Safety Instructions . . . . . . . . . . . . . . . . . 5 Air Circulation Installing the Projector in Proper Directions Moving the Projector Cautions in Handling the Projector Compliance . -
Page 4: To The Owner
SIDE and TOP 1.5' (50 cm) 1.5' (50 cm) – If the projector is unused for an extended time, unplug the projector from the power outlet. CAUTION ON HANGING FROM THE CEILING When hanging the projector from the... -
Page 5: Safety Instructions
The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register. -
Page 6: Air Circulation
Remove any dirt or dust that has accumulated on the projector. If the projector reaches a time set in the timer setting, a Filter replacement icon (Fig. 1) appears on the screen and WARNING FILTER indicator on the top panel lights up (see below), indicating that the filter replacement is necessary. -
Page 7: Installing The Projector In Proper Directions
Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture in upward, downward, or inclined position in perpendicular direction to the horizontal plane. -
Page 8: Moving The Projector
For information about transporting the projector by courier or any other transport service, consult your dealer. – Do not put the projector in a case before it is cooled enough. Cautions in Handling the Projector Do not hold the lens or the top cover when lifting or moving the projector. -
Page 9: Compliance
Telephone No. : (818)998-7322 The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. AC Power Cord for the United States and Canada: AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). -
Page 10: Part Names And Functions
Front Back Bottom Part Names and Functions q Indicators w Top Cover e Top Cover Release Button r Infrared Remote Receiver (Front) t Projection Lens (optional) y Light-Block Sheet u Adjustable Feet i Air Intake Vent o Filter Cover !0 Lamp Cover !1 Exhaust Vent CAUTION Hot air is exhausted from the exhaust vent. -
Page 11: Rear Terminal
(not supplied). USB CONNECTOR (Series B) Use this connector when controlling a computer with the remote control of the projector. Connect the USB terminal of your computer to this connector with the supplied USB cable (p.20). CONTROL PORT CONNECTOR... -
Page 12: Side Control And Indicators
Part Names and Functions Side Control and Indicators Side Control ON/STAND-By button Turn the projector on or off (pp.23–24). INPUT button Select an input source (pp.31–33). LENS button Enter the focus, zoom, and lens shift adjustment mode (p.27). Point ed7 8 buttons –... -
Page 13: Remote Control
– Execute the selected item (p.25). – Expand or compress the image in the Digital zoom mode (p.40). !0 MOUSE POINTER button Move a pointer of the projector or a pointer for wireless mouse operation (p.30). !1 NETWORK button Select the Network input. (Optionally available). - Page 14 Part Names and Functions Remote Control !3 MENU button Open or close the On-Screen Menu (p.25). !4 P-TIMER button Operate the P-timer function (p.29). !5 D .ZOOM button Select the Digital zoom +/- mode and resize the image (p.40). !6 ZOOM ed buttons Zoom in and out the images (p.28).
-
Page 15: Remote Control Battery Installation
16.4’ (5 m) and 60 degrees in front and rear of the projector. Infrared Remote Receivers are provided both in front and back of the projector. You can conveniently use both of the receivers (pp. 10, 51). Wired Remote Control Transmitter The remote control can be used as a wired remote control. -
Page 16: Remote Control Code
Change the remote control code for the projector first before changing that for the remote control. See “Remote control” in the Setting Menu on page 51. -
Page 17: Installation
Rotate the adjustable feet and tilt the projector to the proper height; to raise the projector, rotate the both feet clockwise. To lower the projector or to retract the adjustable feet, rotate the both feet counterclockwise. To correct keystone distortion, press the KEYSTONE button on the remote control or select Keystone from the menu (see pages 14, 29, 40, 44). -
Page 18: Lens Installation
Slide the light-block sheet upward and remove it. Hold the lens with one hand and pull the Lens Lock Lever upward with the other hand. Remove the lens from the projector. ✽ Do not touch the glass part of the lens with your hand. - Page 19 Attaching the lens to the projector Fit the lens to the projector. Make sure that the lens is fully inserted to the projector. Push the Lens Lock Lever downward. Make sure that the lens is properly locked. Slide the light-block sheet in the groove to mount.
-
Page 20: Connecting To A Computer (Digital And Analog Rgb)
G B R H/V V Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. (✽ = Cables not supplied with this projector.) • Serial Cross Cable ✽ • USB Cable Monitor Output... -
Page 21: Connecting To Video Equipment (Video, S-Video)
Composite Video (Y, Pb/Cb, Cr/Pr) Output cable Video Y - Pb/Cb - Pr/Cr Y - Pb/Cb - Pr/Cr = Cables not supplied with this projector.) ✽ Monitor Out Signal Table Input Terminal Monitor Out RGB (PC analog) D-sub15 RGB (SCART) -
Page 22: Connecting The Ac Power Cord
NOTE ON THE POWER CORD AC power cord must meet the requirements of the country where you use the projector. Confirm the AC plug type with the chart below and proper AC power cord must be used. If the supplied AC power cord does not match your AC outlet, contact your sales dealer. -
Page 23: Basic Operation
Lamp control status icon (see page 51) appear on the screen. If the projector is locked with a PIN code, PIN code Input Dialog Box will appear. Enter the PIN code as instructed below. -
Page 24: Turning Off The Projector
When the projector has cooled down enough, the POWER indicator lights green and then you can turn on the projector. To unplug the AC power cord, wait until the projector is completely cooled down. TO MAINTAIN THE LIFE OF THE LAMP , ONCE YOU TURN THE PROJECTOR ON, WAIT AT LEAST FIVE MINUTES BEFORE TURNING IT OFF . -
Page 25: How To Operate The On-Screen Menu
How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. Press the MENU button on the side control or the remote control to display the On-Screen Menu. -
Page 26: Menu Bar
Store/Quit] (pp. 45–47 .) Information Menu Display the input source information (p. 28). Setting Menu Used to set the projector’s operating configurations (pp. 48–55). Screen Menu Used to adjust the size of the image. [Normal/Wide/Custom/ Keystone/Ceiling/Rear/ Reset] (pp. 43-44). -
Page 27: Operating With Projector Control
Operating with Projector Control Lens Operation The following lens operation can be made with the Lens button on the side control. Press the LENS button to enter each lens operation mode. The selected adjustment display appears on the screen. Zoom ➜ Focus ➜ Lens Shift ➜... -
Page 28: Operating With Remote Control
INFO . button Information display can be used to confirm the current operating condition of the projector and the signal being projected through the projector. Press the INFO. button on the remote control to display the information window on the screen. -
Page 29: Keystone Button
FILTER button Press and hold the FILTER button for more than five seconds to operate electrically operated filter to replace the filter. NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. -
Page 30: Pointer Function
Basic Operation Pointer Function You can move the Pointer of the projector with the remote control to emphasize a part of the projected image. Press the POINTER button to activate the Pointer function. Use the MOUSE POINTER button to move the Pointer. -
Page 31: Input Selection
Input Side Control Side Control Operation Press the INPUT button on the side control. It switches to INPUT 1, INPUT 2, and INPUT 3 as you press the INPUT button. Before using the INPUT button on the side control, you must select a correct input source by On-Screen Menu and the latest input source will be displayed. -
Page 32: Computer Input Source Selection
• HDCP (High-bandwidth Digital Content Protection) is a system for protecting digital entertainment content which is delivered by DVI (Digital Visual Interface) from being copied. T he specification of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP . WHEN SELECTING INPUT (5 BNC INPUT jACKS ) When connecting the computer output [5 BNC Type (Green, Blue, Red, Horiz. Sync, and Vert. Sync.)] from the computer to G, B, R, H/HV, and V jacks: When your computer is connected to the INPUT 2 (5 BNC INPUT JACKS) terminal, select RGB. -
Page 33: Video Input Source Selection
Video Input Source Selection Menu Operation WHEN SELECTING INPUT 1 (COMPUTER INPUT TERMINALS ) When connecting to video equipment, select the type of Video source in the Source Select Menu. RGB (Scart) When scart video equipment is connected to the INPUT 1 (ANALOG) terminal, select RGB (Scart). -
Page 34: Computer Input
WXGA, or UXGA (refer to “Compatible Computer Specifications” on pages 71–72). If a computer is selected as a signal source, this projector automatically detects the signal format and tunes to project a proper image without any additional settings. (Some computers need to be set manually.) -
Page 35: Auto Pc Adjustment
To store the adjusted parameters . The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.34). See MANUAL PC ADJUSTMENT on pages 36–37 . -
Page 36: Manual Pc Adjustment
Computer Input Manual PC Adjustment Some computers employ special signal formats which may not be tuned by Multi-Scan system of this projector. Manual PC Adjustment enables you to precisely adjust several parameters to match those special signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. - Page 37 Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select [Yes]. All adjustments will return to their previous figures. Mode free To clear the adjusted data, select Mode free and then press the SELECT button.
-
Page 38: Image Level Selection
Use the Point ed buttons to move the red frame pointer to the desired image level and then press the SELECT button. Standard Normal picture level preset on the projector. Real Picture level with improved halftone for graphics. IMAGE 1–10 User preset picture adjustment in the Image Adjust Menu. -
Page 39: Screen Size Adjustment
True Provide the image in its original size. When the original image size is larger than the screen size (1024 x 768), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to pan the image. When adjusted, the arrows will turn red. When reached to the correction limits, the arrows will disappear. - Page 40 When this function is set to “On, ” the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to “On, ” the picture is left/right reversed.
-
Page 41: Video Input
When Video System is PAL -M or PAL -N, select the system manually. PAL/SECAM/NTSC/NTSC4 .4/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL -N. -
Page 42: Image Level Selection
Image Select Menu icon. Use the Point ed buttons to move the red frame pointer to the desired image level and then press the SELECT button. Standard Normal picture level preset on the projector. Cinema Picture level adjusted with fine tone. IMAGE 1–10 User preset picture adjustment in the Image Adjust Menu. -
Page 43: Screen Size Adjustment
Screen Size Adjustment Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Screen Menu icon. Use the Point ed buttons to move the red frame pointer to the desired function and then press the SELECT button. - Page 44 When this function is set to “On, ” the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to “On, ” the picture is left/right reversed.
-
Page 45: Picture Image
Image Adjustment Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display the adjustment dialog box. - Page 46 Picture Image COLOR SELECTION MODE (continued) COLOR M . Return to the COLOR MANAGEMENT POINTER. (If you press the MENU button on the side control or the remote control, it returns to the COLOR MANAGEMENT POINTER and you will need to reselect and readjust the color.) MENU Return to the IMAGE ADJUST Menu.
- Page 47 Off ..Progressive scan mode is “Off. ” On ..Progressive scan mode is “On. ” Film . . . For watching a film. With this function, the projector reproduces pictures faithful to the original film quality.
-
Page 48: Setting
Setting This projector has a Setting menu that allows you to set up other various functions. Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. - Page 49 After capturing the projected image, go to the Logo select function and set it to “User” . Then the captured image will be displayed the next time you turn on the projector. To cancel the Capture function, select [No]. ✔...
- Page 50 Setting Logo PIN code lock This function prevents an unauthorized person from changing the screen logo. Off ..The screen logo can be changed freely from the Logo Menu. On ..The screen logo cannot be changed without a Logo PIN code.
- Page 51 (Code 1) and the other seven codes (Code 2 to Code 8). The same code should set on both the projector and the remote control. For example, operating the projector in “Code 7” , the remote control code also must be switched to “Code 7”...
- Page 52 Off ..Power Management function is off. ✔ Note: • Factory default is “Ready: 5 min. ” On start When this function is set to “On, ” the projector will be automatically turned on just by connecting the AC power cord to the wall outlet. ✔ Note: • Be sure to turn off the projector properly (see “Turning Off the...
- Page 53 Off ..Unlocked. On1 . . . Enter the PIN code every time turning on the projector. On2 . . . Enter the PIN code to operate the projector once the power cord is disconnected; as long as the AC power cord is connected, the projector can be operated without a PIN code.
- Page 54 A NEW PIN CODE IN COLUMN OF THE PIN CODE NO . MEMO ON PAGE 76, AND KEEP IT SECURELy . IF yOU FORGET yOUR PIN CODE, THE PROjECTOR CAN NO LONGER BE STARTED . Lamp counter This function is used to reset the lamp counter.
- Page 55 (Fig. 1) appears on the screen and the total accumulated time turns red, indicating that the filter replacement is necessary. If the filter is out of scroll and the projector reaches a time set in the timer setting, Fig. 2 appears on the screen, indicating that the filter cartridge replacement is necessary.
-
Page 56: Maintenance And Care
This projector has an electrically operated filter which helps you to replace the filter easily. The projector monitors the condition of the filter at all time and replaces a filter with a new one automatically when it detects the clogging. -
Page 57: Replacing The Filter Cartridge
Replacing the Filter Cartridge Turn off the projector, and unplug the AC power cord from the AC outlet. First, clean up the dust on the projector and around the air vents. Press s on the filter cover to release the latch and open the filter cover. -
Page 58: Resetting The Filter Counter
Maintenance and Care Resetting the Filter Counter Be sure to reset the Filter counter after replacing the filter and the filter cartridge. Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Setting Menu icon. -
Page 59: Lamp Replacement
Lamp Replacement When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights orange. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode. -
Page 60: Resetting The Lamp Counter
Note: • Do not reset the Lamp counter without replacing the lamp. Be sure to reset the Lamp counter only after replacing the lamp. ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering, give the following information to the dealer. Model No . of your projector ● Replacement Lamp Type No . ● Lamp counter PLC-XP100L/ PLC-XP100BKL POA-LMP108 (Service Parts No. -
Page 61: Lamp Handling Precautions
Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. -
Page 62: Cleaning The Projection Lens
Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the cabinet. When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. -
Page 63: Warning Indicators
Warning Indicators The WARNING indicators show the state of the function which protects the projector. Check the state of the WARNING indicators and the POWER indicator to take proper maintenance. The projector is shut down and the WARNING TEMP. indicator is blinking red. -
Page 64: Appendix
A problem may be noticed with your graphics controller rather than with the projector. (When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the projector. Turn on equipment in the order of the projector and computer.) 6. - Page 65 WARNING: High voltages are used to operate this projector . Do not attempt to open the cabinet . If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the problem. We will advise you how to obtain service.
-
Page 66: Menu Tree
Appendix Menu Tree Computer Input/Video Input Input Input 1 Input 2 Input 3 Network Information Information ✔ Note: • The Menu display varies depending on the input signal. RGB (PC analog) RGB (Scart) RGB (PC digital) RGB (AV HDCP) Video Y, Pb/Cb,Pr/Cr Video Y, Pb/Cb,Pr/Cr S-video Image Adjust Image Adjust Input H-sync freq. - Page 67 Computer Input System ✽ System displayed in the System Menu varies depending on the input signal. PC Adjust Auto PC adj. Fine sync. Total dots Position H Position V Current mode Clamp Display area - H Display area - V Reset Mode free Store...
- Page 68 On/Off Logo PIN code change Quit Quit Auto/Normal/Eco 1/Eco 2 Yes/No Normal/Max Code 1 Code 8 Quit Both/Front/Back Mouse Projector Ready Shut down 1–30 Min. Quit On/Off Finger/Arrow/Dot Key lock Projector Remote Control PIN code lock Off/On1/On2 PIN code change...
-
Page 69: Indicators And Projector Condition
The projector is operating normally. The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed and the POWER indicator lights green. The projector is in the Power management mode. - Page 70 The lamp cannot light up. (The lamp has been cooled down ✽ enough and the projector is in stand-by mode and ready to be turned on with the ON/STAND-BY button.) The lamp has been used overtime. Replace the lamp immediately and then reset the lamp counter.
-
Page 71: Compatible Computer Specifications
Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V- and H-Frequency mentioned below and less than 180 MHz of Dot Clock. PC Adjustment is limited when selecting these modes. ON-SCREEN RESOLUTION H-Freq . - Page 72 Appendix When an input signal is digital from the DVI terminal, refer to the chart below. ON-SCREEN RESOLUTION DISPLAy D-VGA 640x480 D-480p 720x480 D-575p 720x575 D-SVGA 800x600 D-XGA 1024x768 D-WXGA 1 1366x768 D-WXGA 2 1360x768 D-WXGA 3 1376x768 D-WXGA 4 1360x768 D-WXGA 5 1366x768...
-
Page 73: Technical Specifications
Technical Specifications Mechanical Information Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Panel Resolution LCD Panel System Panel Resolution Number of Pixels Signal Compatibility Color System High Definition TV Signal Scanning Frequency Optical Information Projection Lamp... -
Page 74: Optional Parts
PJ-Net Organizer Plus IIC Lens Replacement The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses. For installation and replacement of the lens, always contact the sales dealer. The projector lens must be installed or replaced by well-trained sales or service engineers. -
Page 75: Configurations Of Terminals
Configurations of Terminals ANALOG/ MONITOR OUT (Mini D-sub 15 pin) DIGITAL DVI-D (DVI 4 PIN) USB CONNECTOR (Series B) CONTROL PORT CONNECTOR (D-sub 9 pin) +5V Power Red Input Green Input Ground (Vert. sync.) Blue Input Sense 0 Sense 2 DDC Data Ground (Horiz.sync.) Horiz. -
Page 76: Pin Code Number Memo
PIN Code Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. -
Page 77: Dimensions
Dimensions Unit: inch (mm) 6.5º MAX 5.75 (146) 14.57 (370.0) 4.33 (110) 5.20 (132) Appendix 4.33 (110) 4.13 (105) Screw Holes for Ceiling Mount Screw: M6 Depth: 0.393 (10.0) -
Page 78: Serial Control Interface
Appendix Serial Control Interface This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. Operation Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC. -
Page 79: Functional Execution Command
Functional Execution Command Format The command is sent from PC to the projector with the format below; 'C' [Command] 'CR' Command: two charactors (refer to the command table below. -The projector decodes the command and returns the 'ACK' with the format below;... -
Page 80: Status Read Command
'Charactor string' with the format below; Command Function Status Read Temperature Read The tables on page 79 and 80 show the typical command lists for controlling the projector. Please consult your local dealer for further information of other commands. Projector Projectro status Return... - Page 81 SANyO Electric Co ., Ltd . KC3AL-a...