American Standard HURON 3312 Installation Instructions

INSTALLATION INSTRUCTIONS
HURON BOWL WITH EVERCLEAN
ONE PIECE TOILET
Models 3312.001, 3313.001, 3341.001, 3342.001
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!
NOTE: Pictures may not exactly define contour of china and components.
NOTE: For proper operation these products require a minimum of 30 psi line pressure.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver
Hacksaw Wax Ring/Gasket
1 REMOVE OLD TOILET:
a. Close flush valve completely.
b. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug wall waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
2 DIMENSIONS (Nominal)
NOTE: Distance from floor to closet flange centerline (rough-in) must be 4-1/4" (108 mm) with flange surface flush to
1/16" (1.6mm) max. beyond finished wall.
5-1/2"
(140mm)
18-7/8"
(479mm)
24-7/8"
(632mm)
FINISHED WALL
1-1/2" (38mm)
SPUD CONNECTION
C/L OUTLET
4-1/4"
(108mm)
FINISHED
C/L of
10-3/4" FLOOR
1/2"(13mm)
(273mm)
Dia. Holes
3
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn
90°, and slide into place 6" (152 mm)
apart and parallel to floor. (Use putty to
hold bolts in place if necessary.) Brace
under flooring as needed and drill two
mounting pilot holes as shown.
HURON 3312/3313
17-1/8" TOP SPUD
13-3/4"
(349mm)
17-1/8"
6"
(435mm)
(152mm)
C/L OUTLET
4-1/4"
(108mm)
6" (152mm)
DIA. HOLE
8-1/2"
(25mm x 13mm)
IN WALL
(216mm)
CLOSET
BOLTS
4-1/4"
(108mm)
10-3/4"
(267mm)
6"
(152mm)
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 1 3
®
Adjustable Wrench
Flexible Supply Tube
24-7/8"
(632mm)
5-1/2"
(140mm)
18-7/8"
(479mm)
FINISHED
WALL
C/L OF SUPPLY
C/L OUTLET
4-1/4"
(108mm)
(2) SLOTS
C/L of
1" x 1/2"
10-3/4"
1/2"(13mm)
(273mm)
DIA. HOLES
4
FLUSH TO
1/16" (1.6mm)
EXPOSED
CLOSET
FLANGE
PILOT
HOLES
Sealant Tape Measure
Closet Bolts Carpenters Level
NOTE: Mounting surface must be clean and perpendicular
to the floor before new toilet is installed!
HURON 3341/3342
17-1/8" BACK SPUD
6"
(152mm)
17-1/8"
(435mm)
(2) SLOTS
FINISHED
1" x 1/2"
FLOOR
(25 x 13mm)
NEOPRENE
SEAL
INSTALL NEOPRENE OR GRAPHITE FELT SEAL*
Install seal evenly around waste flange (horn).
Apply a thin bead of sealant around base flange.
*NOTE: Wax seal not recommended for this application.
730174 3-100 Rev. B
3" (76mm)
DIA. HOLE
IN WALL
13-3/4"
(349mm)
6" (152mm)
DIA. HOLE
IN WALL
11"
(279mm)
15-1/4"
(387mm)
4-1/4"
8-3/8"
(108mm)
(213mm)
SEALANT