Related Manuals for Sanyo CE42LH2DPB
Summary of Contents for Sanyo CE42LH2DPB
- Page 1 INSTRUCTION MANUAL LCD Monitor Please read this Instruction book before using your LCD monitor. We wish you many hours of pleasure from your new LCD monitor. CE42LH2R CE42LH2DPB CE42LH2WP...
-
Page 2: Table Of Contents
Sound menu ........9 Robust monitor (CE42LH2R， CE42LH2DPB) The robust monitor can be used in a wide variety of environments for dusty and oily circumstance such as fast food, digital signage, industrial and public display. -
Page 3: Safety Precautions
CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but following basic rules for its installation, use and servicing. Installation and Use Do not allow anything to rest on the power cord. -
Page 4: Servicing
If the LCD monitor does not operate normally by following the operating instructions. If the LCD monitor has been exposed to rain or water. (CE42LH2R/CE42LH2DPB model only) Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage. -
Page 5: Ac Power Cord Requirement
Software upon and with the Product. 2. You may not transfer any of your license rights in the Software without the prior written consent of SANYO and if consent is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND provided that the transferee has read and agreed to accept the terms and conditions of this license. -
Page 6: Installation
Step: 1 Mains Connection nector as required. 1. Connect the in-line power connector to the Mains Inlet as shown above. 2. Connect the power cord of the LCD monitor to a suitable wall outlet. As this product does not have a mains On/Off switch, please ensure your mains plug is easily accessible. -
Page 7: Remote Control
FOR EU USERS countries and do not apply to countries in other areas of the world. Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and/or reused. batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste. -
Page 8: Controls And Menus
INSTALLATION Controls and Menus å The LCD display has a Standby light to show there is power. Switching into/from standby mode The Standby mode is used for switching the LCD monitor off for short periods of time. In standby mode the monitor is switched off but is still receiving mains power. -
Page 9: Menu Operation
Picture menu Advanced settings Use the button to select Advanced settings and press button to enter the sub menu as follows. DCDi (Directional Correlational Deinterlacing) is used to process moving angled edge in deinterlacing to get the smoothest and most natural image. -
Page 10: Pc Adj. Menu
MENU OPERATION Language is used to select the preferred language. Use the button to select English, French, German, Italian, Spanish or Dutch. H-Position changes the OSD position horizontally by using the button. V-Position changes the OSD position vertically by using the button. -
Page 11: Installation Mode
Installation Mode Installation Mode On program Tuner Menu Max Volume Winter mode RC inhibition Child Lock Address Baud rate Panel protection AV Auto shut off Network Standby On Timer Function LED light setting Network initial Temperature Error IP Address Subnet Gateway Select Adjust... -
Page 12: Operation
Select screen size from FULL, FULL ALL, ZOOM 16:9, TITLE IN 16:9, ZOOM 14:9, TITLE IN 14:9, NORMAL or NATURAL WIDE by pressing the WIDE button repeatedly on the Remote Control. When in AV2 (RGBHV) or PC mode FULL or NORMAL can be selected. -
Page 13: Pip/Pop Operation
PIP/POP Operation Using this function, you can enjoy a DVI or Network program and an image (AV1, AV2, AV3 or PC input) at the same time. Press the ON/OFF button on the Remote Control repeatly to select PIP1, PIP2, POP or OFF mode. During the PIP/POP mode, press the Main/Sub Picture Swap but- ton will switch the location for main and sub picture. -
Page 14: Operation (In Text Mode)
Teletext Operation Teletext is only available via external sources. Teletext mode can be operated by the following buttons on the Re- mote Control. Some buttons have dual functions. TXT/TV Press TXT/TV button to select teletext. Press again will display: AV mode: AV/TEXT mode/MIX mode/AV. Note: MIX mode: AV (broadcast image) screen and the contents of TEXT (superimposed) are displayed simultaneously. -
Page 15: Specifications/Helpful Hints
Model name Contrast Ratio CE42LH2R CE42LH2DPB 1000:1 CE42LH2WP LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels. -
Page 16: Dimensions
CE42LH2WP 989.0 925.4 1027.0 953.0 930.25 VIEWING AREA(H) DIMENSIONS (WALL MOUNT SCREW) 10 x M6, 1.0 PITCH x 12MM 165.9 126.0 50.8 17.6 402.9 178.5 417.9 ø4.2 (RC RECEIVER) ø4.2 (LED INDICATOR) Unit: mm 418.4 418.4 400.0 200.0 100.0 41.8 Handles x 2 Control buttons 43.7... -
Page 17: Pc/Dvi-D/Component Signal Support Timing List
PC/DVI-D/COMPONENT SIGNAL SUPPORT TIMING LIST PC signal support timing Vertical Resolution Frequency Frequency 720 x 400 31.47 70.09 640 x 480 31.43 59.88 640 x 480 37.50 75.00 640 x 480 37.86 72.81 640 x 480 43.27 85.00 640 x 480 35.00 66.67 640 x 480... -
Page 18: Rs232C Command Tables
Functional Execution Command Table Command POWER ON POWER OFF POWER ON/ OFF (toggle) Wide toggle Input Wide “Natural” direct Wide “Zoom 16:9” direct Wide “Title in 16:9” direct Wide “Zoom 14:9” direct Wide “Title in 14:9” direct Wide “Full” direct Picture Wide “Normal”... - Page 19 Time Read Command Table Status read command Status of accumulated lifetime of panel. CR PANELH (The same as CR_LAMPH Command) Status of accumulated lifetime of monitor. CR MONH Sound control Read Command Table Status read command CR VOLUME Status of volume value. CR MUTE Status of MUTE.
- Page 20 N7RAK/ N7RBK/ N7RPK...
-
Page 21: Installation Guidelines
INSTALLATION GUIDELINES CONSIGNES D’INSTALLATION INSTRUCCIONES DE INSTALACIÓN INSTALLATIONSRICHTLINIEN INSTALLATIEHANDLEIDING ISTRUZIONI DI INSTALLAZIONE CE42LH2WP CE42LM6WP CE42SR2 CE52LH2WP CE52SR2 CE52SR3 IMPORTANT PLEASE READ THESE GUIDE LINES PRIOR TO UNPACKING AND INSTALLATION. IMPORTANT VEUILLEZ LIRE ATTENTIVEMENT CES CONSIGNES AVANT DE DEBALLER ET D’INSTALLER LE MONITEUR. ¡IMPORTANTE! POR FAVOR, LEA ESTAS INSTRUCCIONES ANTES DE PROCEDER AL DESEMBALAJE Y LA INSTALACIÓN. - Page 22 English To All Installers, This monitor is sealed to IP66 standard. The integrity of the enclosure MUST NOT be tampered with or breached. The following guide lines highlight those areas of the product that require particular care and attention in order to ensure the integrity of the enclosure.
- Page 23 In the event that this adhesive sealing is broken when the set is returned, SANYO can not accept liability for the condition. • Vent caps can be easily damaged. The set should always be lifted (DO NOT SLIDE) and always •...
- Page 24 • This is to identify if the screws have been removed. Any attempt to remove the anti-tamper ink will be CLEARLY visible. • In the event that the back plate is removed, the sealing of the set will be compromised, therefore, SANYO can not accept liability for any related failure. ANTI-TAMPER INK therefore MUST NOT be removed.
- Page 25 REAR A.V.SHIELD COVER/TERMINAL COVER ting the terminal cover and rear A.V.cover. ALL Check point Check gasket is in place inside the cover. Gasket is important to seal cable area. MAKE SURE CORD FITS IN THE MOULD SHAPE Check point recess of the terminal base. GASKET IN THE TERMINAL COVER GASKET IN THE RECESS...
- Page 26 • The mains lead is secured to the back plate using a weatherproof cable gland. Do not loosen the gland as this will impair the weatherproof sealing. VIEW INSIDE ENCLOSURE ADHESIVE TREATMENT • Sets must be handled with EXTREME care to ensure that this seal is not damaged. Please take particular care not to drop or bump the set during handling/installation.
- Page 27 INSTALLING POSITION When the monitor installed outside, it SHOULD NOT set in a position where the screen is subjected to direct sun light. If it can’t be done, please prepare adequate shading. Di- rect sun light can cause the screen surface temperature This causes a black shadow to appear on the screen, which will disappear when the screen temperature returns 1.
- Page 28 CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but following basic rules for its installation, use and servicing. Installation and Use Do not allow anything to rest on the power cord.
- Page 29 Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage. Important recycling information. Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused.
- Page 30 Software upon and with the Product. 2. You may not transfer any of your license rights in the Software without the prior written consent of SANYO and if consent is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND provided that the transferee has read and agreed to accept the terms and conditions of this license.
- Page 31 Step: 1 Mains Connection nector as required. 1. Connect the in-line power connector to the Mains Inlet as shown above. 2. Connect the power cord of the LCD monitor to a suitable wall outlet. As this product does not have a mains On/Off switch, please ensure your mains plug is easily accessible.
- Page 32 The symbol mark and recycling systems described below apply to EU countries and do not apply to countries in other areas of the world. Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and/or reused.
- Page 33 Controls and Menus å The LCD display has a Standby light to show there is power. Switching into/from standby mode The Standby mode is used for switching the LCD monitor off for short periods of time. In standby mode the monitor is switched off but is still receiving mains power.