Page 1
INSTRUCTION MANUAL LCD Monitor Please read this Instruction book before using your LCD monitor. We wish you many hours of pleasure from your new LCD monitor. PID-42AE1 PID-42AS1...
CAUTION: Please read and retain for your safety. This unit has been designed and manufactured to assure your personal safety, but improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this monitor observe the following basic rules for its installation, use and servicing .
This will often require extensive work by a qualified technician to restore the monitor to normal operation. Important recycling information. Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused .
SERVICING Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules . These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment .
. 2. This End-User License is governed by the laws of the State of California . The End-User and Sanyo agree that any action to enforce or inter- pret the terms of this End-User License shall be brought only in the appropriate state or federal court located in Los Angeles County, Califor- nia .
SERVICING 1. The LCD monitor can be installated by the following two ways: Screw holes for installing Screws: Spec : M6 X 12MM (metric) Material : Stainless Steel Note: Don't install the TV set reversed as shown below : 2. The product should be mounted to wall only as recommended by the manufacturer . 3.
Step: 1 Mains Connection ■ Connect the display unit to VGA, BNC and Scart con- nector as required. Mains Inlet 1. Connect the in-line power connector to the Mains Inlet as shown above . 2. Connect the power cord of the LCD monitor to a suitable wall outlet . ✐...
The symbol mark and recycling systems described below apply to EU countries and do not apply to countries in other areas of the world . Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and/or reused .
INSTALLATION Controls and Menus å Infrared Remote Receiver Power Indicator å The LCD display has a Standby light to show there is power. Switching into/from standby mode The Standby mode is used for switching the LCD monitor off for short periods of time .
Picture menu ■ Advanced settings Use the 5 or 6 button to select Advanced settings and press the 1 or 2 button to enter the sub menu as follows . DCDi (Directional Correlational Deinterlacing) is used to process moving angled edge in deinterlacing to get the smoothest and most natural image .
MENU OPERATION Language is used to select the preferred language . Use the 1 or 2 button to select English, French, German, Italian, Spanish or Dutch . H-Position changes the OSD position horizontally by using the 1 or 2 button . V-Position changes the OSD position vertically by using the 1 or 2 button .
Installation Mode Installation Mode On program Tuner Menu Max Volume Winter mode RC inhibition Child Lock Address Baud rate Panel protection AV Auto shut off Network Standby On Timer Function LED light setting Network initial Temperature Error IP Address Subnet Gateway Select Adjust...
Selection of picture size Select screen size from FULL, FULL ALL, ZOOM 16:9, TITLE IN 16:9, ZOOM 14:9, TITLE IN 14:9, NORMAL or NATURAL WIDE by pressing the WIDE button repeatedly on the Remote Control . ✐ When in AV2 (RGBHV) or PC mode FULL or NORMAL can be selected .
PIP/POP Operation Using this function, you can enjoy a DVI or Network program and an image (AV1, AV2, AV3 or PC input) at the same time . Press the ON/OFF button on the Remote Control repeatly to select PIP1, PIP2, POP or OFF mode . During the PIP/POP mode, press the Main/Sub Picture Swap but- ton will switch the location for main and sub picture .
Teletext Operation Teletext is only available via external sources . Teletext mode can be operated by the following buttons on the Re- mote Control . ✐ Some buttons have dual functions . TXT/TV Press TXT/TV button to select teletext . Press again will display: AV mode: AV/TEXT mode/MIX mode/AV .
Input: DVI-D GROUP Standard Input: Mini D-SUB 15 PIN and Audio 3.5mm Jack Serial Port: RS232C: Input/Output Model name Contrast Ratio PID-42AE1 1000:1 PID-42AS1 The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards . Even though 99 .99% of the pixels are effective, a tiny fraction of the pixels ●...
(WALL MOUNT SCREW) 4 x M6, 1.0 PITCH x 12MM Control buttons DIMENSIONS 1002.8 971.5 1010.3 932.3 VIEWING AREA(H) RC RECEIVER LED INDICATOR 397.2 Unit: mm (WALL M 4 x M6, 1. 23.5...
PC/DVI-D/COMPONENT SIGNAL SUPPORT TIMING LIST ■ PC signal support timing Horizontal Vertical Resolution Frequency Frequency (kHz) (Hz) 720 x 400 31 .47 70 .09 640 x 480 31 .43 59 .88 640 x 480 37 .50 75 .00 640 x 480 37 .86 72 .81 640 x 480...
■ Functional Execution Command Table Command POWER ON POWER OFF Wide “Natural” direct Wide “Zoom 16:9” direct Wide “Title in 16:9” direct Wide “Zoom 14:9” direct Wide “Title in 14:9” direct Wide “Full” direct Wide “Normal” direct AV1 direct RGB direct AV2 RGBHV direct AV2 YPbPr direct AV3 direct...
■ Time Read Command Table Status read command Status of accumulated lifetime of panel . CR PANELH (The same as CR_LAMPH Command) Status of accumulated lifetime of monitor . CR MONH (The same as CR_PROJH Command) ■ Sound control Read Command Table Status read command CR VOLUME Status of volume value .