INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system works properly. •...
(Fig. 2) Removing the unit DIN REAR-MOUNT (Method B) Installation using the screw holes on the sides of the unit. 1. Dashboard 2. Nut (5mm) 3. Spring washer 4. Screw (5 x 14mm) 5. Screw 6. Strap Be sure to use the strap to secure the back of the unit in place.
HOW TO REMOVE AND INSTALL THE FRONT PANEL (OPTIONAL) 1. Press the release button and pull-off the front panel. Store front panel in the case. 2. To install the front panel, insert the panel into the housing and make sure the panel is properly installed, otherwise, abnormalities may occur on the display or some keys may not function properly.
WIRING CONNECTION ANTENNA CONNECTOR IGNITION SWITCH (B+) YELLOW MEMORY BACK-UP BLACK GROUND (B–) BLUE POWER ANTENNA FRONT Lch SPEAKER WHITE/BLACK REAR Lch SPEAKER GREEN/BLACK MAIN UNIT WHITE GREEN (GREY) Rch RED RCA CABLE Lch WHITE GREY FRONT Rch SPEAKER GREY/BLACK VIOLET REAR Rch SPEAKER...
OPERATION GENERAL OPERATION • ON/OFF Switch on the unit by pressing any button [except (4)]. When system is on, press PWR button (9) to turn off the unit. • FACEPLATE RELEASE Press button (7) to detach the removable faceplate. 6 16 button (7) and eject button...
Page 7
The adjustment mode will change in the following order: Volume By pressing VOL button + (11) or VOL button – (12), it is possible to adjust the desired sound level. • LOUDNESS Press BND/LOU button (13) for several seconds to reinforce the bass output and display will show “LOUD”.
RADIO OPERATION • BAND SELECTION At tuner mode, press BND/LOU button (13) to select the desired band. The reception band will change in the following order: • STATION SELECTION Press MANU/SKIP automatic seek function. To select manual tuning mode, press for several seconds until “MANUAL”...
Page 9
CD OPERATION • SELECT TRACKS Press MANU/SKIP previous track or the following track. Track number shows on display. Hold MANU/SKIP fast forward. CD play starts from when you release the button. • PAUSE PLAYING Press PAU button (20) to pause CD player. Press it again to resume play. •...
Page 10
Note: A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape etc., onto the label side or the recording side of any discs, as it may cause a malfunction.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage Sensitivity (S/N = 30 dB) Stereo Separation Frequency Coverage Sensitivity (S/N = 20 dB)
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. The car ignition switch is not on. The fuse is blown. Disc cannot be Presence of CD disc inside loaded or ejected.
Page 13
In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Factory Service Center at the user’s expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below.
Page 16
21605 Plummer Street Chatsworth, CA91311 ECD-T1535. Issue Number 1. Printed in Hong Kong 88-C1007-09...