allen PRO 430 Operations & Parts Manual
  1. Manuals
  2. Brands
  3. allen Manuals
  4. Trowels
  5. PRO 430
  6. Operations & parts manual

allen PRO 430 Operations & Parts Manual

Power trowels
Hide thumbs
Table of Contents

Advertisement

Quick Links

OPERATIONS-PARTS
MANUAL
MANUAL
Walk-behind
Power Trowels
055561; 01/12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PRO 430 and is the answer not in the manual?

Questions and answers

Related Manuals for allen PRO 430

Summary of Contents for allen PRO 430

  • Page 1 OPERATIONS-PARTS OPERATIONS-PARTS MANUAL MANUAL Walk-behind Power Trowels 055561; 01/12...
  • Page 2 This manual, or a copy of it, must be kept with the machine at all times. There is a manual storage container located on the machine for your convenience. 055561; 01/12...
  • Page 3 No part of this manual may be reproduced or transmitted in any form or by any means, electronics or mechanical, for any purpose, without the express written permission of Allen Engineering Corporation (AEC). AEC assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual.
  • Page 4 B. New Gear Boxes ........Two Years The above listed warranty periods are effective for Allen Machines with a first day of use by End User on April 1, 2007 or later. Warranty period begins on first day of use by End User. This first day of use is established by the date of a completed Allen Warranty Card or a Bill of Sale to the End User.

  • Page 5: Table Of Contents

    Table of Contents Sect No. Title Page Limited Warranty ..........ii Information Contained In This Manual .
  • Page 6 Table of Contents, continued Parts ........... .4-1 Factory Service Information .
  • Page 7 Complete any warranty requirements as specified by the engine manufacturer in their instructions found inside the manual box located on the back of the riding trowel operator’s seat. Your engine and clutch is not manufactured by Allen Engineering Corporation, Inc, and therefore is not covered under Allen Engineering Corporation, Inc warranty.
  • Page 8 Dealer Information Your Dealer has Allen Engineering Corporation trained mechanics and original Allen replacement parts. Always contact the Allen Dealer who sold you this machine for Allen Certified repairs and replacement parts. Place Allen Dealer information below for future reference...
  • Page 9 Ordering Parts Section 4.0 contains illustrated parts lists for help in ordering replacement parts for your machine. Follow the instructions below when ordering parts to insure prompt and accurate delivery: All orders for service parts - include the serial number for the machine. Shipment will be delayed if this information is not available.
  • Page 10 Model Number - Serial Number Codes Manufacturer’s Codes: When ordering parts or requesting service information, you will always be asked to specify the model and serial numbers of the machine. The legends below specifically defines each significant character or group of characters of the Model Number and Serial Number codes. Model Number MODEL SERIES...
  • Page 11 Unit Identification Unit Identification Plate Location: An identification plate listing the model number and the serial number is attached to each unit and is located on the rear lower left side of mainframe. Refer to Figure 1 for serial number and model number location.
  • Page 12 Technical Specifications Measurements in this manual are in U.S. units and their customary metric units (i.e., metric units contained within brackets [8 mm]). Machine Features: • Dimensions (L x W x H) inch [mm] ....77.5x40.5x54 (guard ring/long handle) .
  • Page 13 Technical Specifications, continued • Run Time (Approximate) hr ......2.5 • Transmission Type ......Clutch •...
  • Page 14 Engine Specifications Honda GX160 Engine Information (5.5 HP) Engine Type: ..........Air-cooled 4-stroke OHV Bore x Stroke: .
  • Page 15 Engine Specifications (cont’d) Honda GX390 Engine Information (13 HP) Engine Type ..........Air-cooled 4-stroke OHV Bore x Stroke .
  • Page 16 Ear SPL Power Level Press Overall Overall Maximum dB (A) dB (A) dB (A) m/sec² m/sec² m/sec² Honda 60.4 90.5 88.9 2.34 This information was acquired from sound and vibration analysis tests conducted at Allen Engineering Corporation test facilities. 055561; 01/12...
  • Page 17 Fax: +4631298876 Email: tv@lin-pro.se Signature of Authorized Person(s): Typed name of Authorized Person(s): Jay Allen Scott Sugg Title of Authorized Person(s): Jay Allen - President Scott Sugg - VP of Operations Date and place of issue: 4/21/2010 Paragould, AR 055561; 01/12...
  • Page 18 INTENTIONALLY LEFT BLANK 055561; 01/12...

  • Page 19: Safety

    SECTION 1 SAFETY Section 1 SAFETY 055561; 01/12...

  • Page 20: State Regulations

    SECTION 1 State Regulations SAFETY CALIFORNIA PROPOSITION 65 WARNING Gasoline engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. 055561; 01/12...

  • Page 21: Federal Regulations

    SECTION 1 Federal Regulations SAFETY SILICOSIS WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other miner- als and rocks.

  • Page 22: General Safety Precautions

    SECTION 1 General Safety Precautions SAFETY 1.1.1 Safety-Alert Signs This manual contains Safety-Alert Signs, as defined below, which must be followed to reduce the possibility of improper servi ce damage to the equipment or personal injury. Read and follow all Safety-Alert Signs included in this manual. NOTE defines an operating procedure, condition, etc.

  • Page 23: Spark Arrestor Notice

    SECTION 1 SAFETY Spark Arrestor Notice 1.2.1 Laws Pertaining to Spark Arrestors Some states require that in certain locations arrestors be used on internal combustion engines. A spark arrester is a device designed to prevent the discharge of spark or flames from the engine exhaust. It is often required when operating equipment on forested land to prevent the risk of fires.

  • Page 24: General Safety

    SECTION 1 SAFETY General Safety • NEVER operate this equipment without proper protective clothing, safety glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations. • Avoid wearing jewelry or loose fitting clothes that may get caught on the controls or moving parts as this can cause serious injury.
  • Page 25 SECTION 1 1.3, continued SAFETY General Safety • ALWAYS know the location of the nearest fire extinguisher. • ALWAYS know the location of the nearest first aid kit. • ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fire department.
  • Page 26 SECTION 1 1.3, continued General Safety SAFETY • NEVER disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties. •...

  • Page 27: Engine Safety

    SECTION 1 1.3, continued Engine Safety SAFETY • DO NOT place hands or fingers inside engine compartment when engine is running. • NEVER operate the engine with heat shields or guards removed. • Keep fingers, hands hair and clothing away from all moving parts to prevent injury. •...

  • Page 28: Transportation Safety

    SECTION 1 1.3, continued Transportation Safety SAFETY • NEVER allow any person or animal to stand underneath the equipment while lifting. • Some walk-behind trowels can be lifted or moved by two people utilizing lifting tubes or other special attachments. Generally, however, they must be lifted using lifting bales and cranes, hoists, or forklifts.

  • Page 29: Safety And Operation Labels

    SECTION 1 Safety and Operation Labels SAFETY The safety and operation labels shown in this section are placed in important areas on the machine to draw attention to potential safety hazards and service information. Should any of these labels become unreadable or damaged, replacement labels can be odered from your dis- tributor.
  • Page 30 SECTION 1 1.6, continued SAFETY Safety and Operation Labels This label is a maintenance reminder to grease the thrust bearing daily. This will ensure that the life span of the bearings will be maintained at their optimal preformance level. This label cautions against allowing cleaning agents, surface treatments, or other foreign substances to contaminate drive components.

  • Page 31: Operations

    SECTION 2 OPERATIONS Section 2 OPERATIONS 055561; 01/12...
  • Page 32 This machine is built with user safety in mind. However, it can present hazards if improperly operated and serviced. Follow operating instructions carefully. If you have any questions about operating or servicing this equipment, please contact your Allen Engineering Dealer or AEC Customer Service at 800-643-0095 or 870-236-7751. 055561; 01/12...

  • Page 33: Introduction

    The pulley engages using a clutch. See the Parts section of this manu- All Allen Engineering Walk-behinds are equipped with a safety shutdown switch. Operating time between fuel refills is approximately 2-1/2 to 3 hours with a rotor speeds of 110 to 135 RPM.

  • Page 34: Start Up Procedures

    3. If lubrication oil does not seep out as the drain plug is being removed, fill with type Allen Oil Kit P/N 048386 gearbox lubricant oil until the oil filler hole overflows. V-Belt Check A worn or damaged V-belt can adversely affect the performance of the trowel.

  • Page 35: Controls

    SECTION 2 Controls OPERATIONS 055561; 01/12...
  • Page 36 SECTION 2 2.3, continued Controls OPERATIONS 1. Fine Pitch Control Handle – To adjust the pitch of the blades, turn the handle either clock- wise or counter-clockwise to achieve the desired blade pitch. 2. Handlebar Adjuster – Change the angle/height of the handle bars by loosening bolts, adjust handlebars to desired location, tighten bolts firmly to hold handlebars in that position.

  • Page 37: Engine Controls

    2.3, continued SECTION 2 Engine Controls OPERATIONS 1. Fuel Filler Cap – Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill. 2. Throttle Lever – Used to adjust engine RPM speed (lever advanced forward SLOW, lever back toward operator FAST).

  • Page 38: Operating Instructions

    SECTION 2 Operating Instructions OPERATIONS 2.3.1 Operating The Trowel The following steps are intended as a basic guide to machine operation, and are not to be considered a complete guide to concrete finishing. We suggest that all operators (experienced and novice) read “Slabs on Grade” published by the American Concrete Institute, Detroit, Michigan.
  • Page 39 SECTION 2 2.3, continued Operating Instructions OPERATIONS Push down on the handle to move the rotor assembly to the right. Pull up on the handle assembly to move the rotor assembly to the left. Pitch Adjustment Different pitch angles are needed as you work the different stages of the concrete. When changing or setting pitch (angle of trowel blades), slow the machine down, set the desired degree of pitch on the left side of the machine and then adjust the right side to match.
  • Page 40 SECTION 2 Notes OPERATIONS 2-10 055561; 01/12...

  • Page 41: Service

    SECTION 3 SERVICE Section 3 SERVICE 055561; 01/12...

  • Page 42: Periodic Maintenance

    SECTION 3 Periodic Maintenance SERVICE Periodic Maintenance Schedule The table below list basic trowel and engine maintenance. Refer to OEM engine manufacturer's Operation Manual for additional information on engine maintenance. A copy of the engine operator's manual was supplied with the machine when it was shipped.

  • Page 43: Trowel Gearbox

    Replace fill plug after proper level has been achieved. Fill so that there is oil 1/2 way in the sight glass. Use Allen Oil only. Each Gearbox has a grease fitting on top cover that must be greased (2 SHOTS ONLY) every 300 operating hours.

  • Page 44: Lift Lever Adjustment

    SECTION 3 Lift Lever Adjustment SERVICE Lift Lever Adjustment Procedure Damage to and/or replacement of a trowel arm can change the adjustment of the lift lever. This can unbalance the trowel arms and cause the riding trowel to wobble during operation. To operate smoothly the lift lever on all trowel arms must be adjusted the same to ensure that the riding trowel is balanced correctly.
  • Page 45 SECTION 3 3.6, continued Lift Lever Adjustment SERVICE TROWEL ARM BLADE FIGURE 3.6.1 PRESSURE PLATE LOCATION SPIDER BOSS FIGURE 3.6.2 FASTENER HARDWARE REMOVAL 055561; 01/12...
  • Page 46 SECTION 3 Notes SERVICE 3-10 055561; 01/12...
  • Page 47 SECTION 4 PARTS Section 4 PARTS 055561; 01/12...
  • Page 48 SECTION 4 Factory Service Information PARTS This section contains the illustrated drawings and parts list for help in identifying and/or ordering replacement parts for your machine. Follow the instructions in the front section of this manual “Ordering Parts” when ordering replacement parts to insure prompt and accurate delivery. All set screws have blue (LOC-TITE™) applied at the factory.
  • Page 49 SECTION 4 Replacement Parts Procedures PARTS We recommend AEC quality replacement parts, available from the AEC Customer Service Department or your nearest AEC Dealer. Part numbers are subject to change without notice. Part numbers might be different outside of the United States of America. Use part numbers listed in the applicable parts list table when you place your order.
  • Page 50 4.1 Illustration SECTION 4 Fine Pitch Adjustment PARTS 055561; 01/12...
  • Page 51 SECTION 4 4.1 Parts List Fine Pitch Adjustment PARTS ITEM PART # DESCRIPTION 015410 FSTN, RHMS 1/4-20 X 3/8 015739 KNOB, ADJUSTABLE HANDLE 015740 FSTN, PIN SPIRAL 3/16 X 1-3/4 015741 SCREW SHAFT, PITCH CONTROL 015742 THRUST BEARING 015743 BUSHING, F/ PITCH CONTROL 015744 WASHER FINE PITCH CNTRL SPACER 015745...
  • Page 52 4.2 Illustration SECTION 4 Positive Pitch Adjustment PARTS 055561; 01/12...
  • Page 53 SECTION 4 4.2 Parts List Positive Pitch Adjustment PARTS ITEM PART # DESCRIPTION 010002 FSTN, HHCS 1/4-20 X 3/4 010018 FSTN, HHCS 5/16-18 X 1/2 GR 5 010019 FSTN, HHCS 5/16-18 X 3/4 GR 5 010081 FSTN, FW 1/4 010089 FSTN, LW 1/4 010090 FSTN, LW 5/16...
  • Page 54 SECTION 4 4.3 Illustration 430 Edging Spider - 032235 PARTS 055561; 01/12...
  • Page 55 SECTION 4 4.3 Parts List 430 Edger Spider PARTS ITEM PART # DESCRIPTION 012990 FSTN, CABLT 3/8-16 X 1-1/4" 015682 External Tooth Lock Washer, Steel, 3/8 in 015683 BOLT, 3/8-16 X 7/8 DOG PT HEX HD CAP 015684 FSTN, NUT HEX JAM 3/8-16 015686 FSTN, SQHSS 3/8-16 X 1 015816...
  • Page 56 SECTION 4 4.4 Illustration 436 Spider - 015893 PARTS 4-10 055561; 01/12...
  • Page 57 SECTION 4 4.4 Parts List 436 Spider PARTS ITEM PART # DESCRIPTION 012990 FSTN, CABLT 3/8-16 X 1-1/4" 015682 FSTN, LW EXT STAR 3/8 015683 FSTN, 3/8-16 X 7/8 DOG CAP SCREW 015684 FSTN, NUT HEX JAM 3/8-16 015686 FSTN, SQHSS 3/8-16 X 1 015688 FSTN, 9/16-18 NF ADJ/MACH SCRW 015816...
  • Page 58 SECTION 4 4.5 Illustration 446 Spider - 024812 PARTS 4-12 055561; 01/12...
  • Page 59 SECTION 4 4.5 Parts List 446 Spider PARTS ITEM PART # DESCRIPTION 012990 FSTN, CABLT 3/8-16 X 1-1/4" 015682 WASHER, 3/8 EXT TOOTH LOCK 015683 BOLT, 3/8-16 X 7/8 DOG PT HEX HD CAP 015684 FSTN, NUT HEX JAM 3/8-16 015686 FSTN, SQHSS 3/8-16 X 1 015688...
  • Page 60 SECTION 4 4.6 Illustration 446SD Spider - 026588 PARTS 4-14 055561; 01/12...
  • Page 61 - OUR QUALITY POLICY The Allen Engineering Team is fully committed to exceeding customer expectations for the quality of the products and services provided through the continuous improvement process of reducing waste, defects, and variability in everything we do.
  • Page 62 SECTION 4 4.7 Illustration 430 Edging Power Unit - 037275 PARTS 4-16 055561; 01/12...
  • Page 63 SECTION 4 4.7 Parts List 430 Edging Power Unit PARTS ITEM PART NO. DESCRIPTION 010002 FSTN, HHCS 1/4-20 X 3/4 010022 FSTN, HHCS 5/16-18 X 1 1/2" LONG 010081 FSTN, FW 1/4 010090 FSTN, LW 5/16 010100 FSTN, NUT HEX 5/16-18 010273 KEY, 3/16 SQ X 2 010464...
  • Page 64 SECTION 4 4.7 Illustration 430 Edging Power Unit (cont’d) PARTS 4-18 055561; 01/12...
  • Page 65 GUARD, ROLLER RH 430 EDGER 047546 PAL NUT- 1/4-20 048239 CLUTCH, Ø3/4 ID BORE NR WE26 048379 DECAL, ALLEN 4 1/2 x 1 1/2 048937 DECAL, MFG. BY ALLEN ENG. 053448 DECAL, LIFT HERE ONLY (SP) 053453 DECAL, SPARK WARNING (SP) 056341 DECAL ALLEN OVAL 2"...
  • Page 66 4.8 Illustration SECTION 4 436 Edging Power Unit - 043491 and 039212 PARTS 4-20 055561; 01/12...
  • Page 67 SECTION 4 4.8 Parts List 436 Edging Power Unit PARTS ITEM PART NO. DESCRIPTION 010002 FSTN, HHCS 1/4-20 X 3/4 010022 FSTN, HHCS 5/16-18 X 1 1/2" LONG 010024 FSTN, HHCS 5/16-18 X 2 GR 5 010081 FSTN, FW 1/4 010090 FSTN, LW 5/16 010100...
  • Page 68 4.8 Illustration SECTION 4 436 Edging Power Unit - (cont’d) PARTS 23 24 4-22 055561; 01/12...
  • Page 69 047546 PAL NUT- 1/4-20 048239 CLUTCH, Ø3/4 ID BORE (5.5 HP) 047843 CLUTCH, 1" BORE (9 HP) 048379 DECAL, ALLEN 4 1/2 x 1 1/2 048937 DECAL, MFG. BY ALLEN ENG. 049771 PLATE, WALKBEHIND LIFTING 053448 DECAL, LIFT HERE ONLY (SP)
  • Page 70 SECTION 4 4.9 Illustration 035724 035726 436 Power Unit PARTS 035728 4-24 055561; 01/12...
  • Page 71 SECTION 4 4.9 Parts List 436 Power Unit PARTS ITEM PART NO. DESCRIPTION 010002 FSTN, HHCS 1/4-20 X 3/4 010022 FSTN, HHCS 5/16-18 X 1 1/2" LONG 010024 FSTN, HHCS 5/16-18 X 2 GR 5 010039 FSTN, HHCS 3/8-16 X 1 3/4" LONG GR5 010082 FSTN, FW 5/16 010090...
  • Page 72 SECTION 4 4.9 Illustration 436 Power Unit - cont’d PARTS 4-26 055561; 01/12...
  • Page 73 DECAL, LIFT HERE ONLY (SP) 053453 DECAL, SPARK WARNING (SP) 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 056341 DECAL ALLEN OVAL 2" X 3.34" WHITE 010019 FSTN, HHCS 5/16-18 X 3/4 GR 5 (Continued from Page 4-25) 4-27 055561; 01/12...
  • Page 74 SECTION 4 4.10 Illustration 035732 035735 446 Power Unit PARTS 4-28 055561; 01/12...
  • Page 75 SECTION 4 4.10 Parts List 446 Power Unit PARTS ITEM PART NO. DESCRIPTION 010002 FSTN, HHCS 1/4-20 X 3/4 010019 FSTN, HHCS 5/16-18 X 3/4 GR 5 010022 FSTN, HHCS 5/16-18 X 1 1/2" LONG 010024 FSTN, HHCS 5/16-18 X 2 GR 5 010039 FSTN, HHCS 3/8-16 X 1 3/4"...
  • Page 76 4.10 Illustration 035732 SECTION 4 035735 446 Power Unit - cont’d PARTS 4-30 055561; 01/12...
  • Page 77 PLATE, WALKBEHIND LIFTING 053446 DECAL, MADE IN USA (SP) 053448 DECAL, LIFT HERE ONLY (SP) 053453 DECAL, SPARK WARNING (SP) 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 056341 DECAL ALLEN OVAL 2" X 3.34" WHITE (Continued from Page 4-29) 4-31 055561; 01/12...
  • Page 78 4.11 Illustration 042037 SECTION 4 446SD Power Unit PARTS 4-32 055561; 01/12...
  • Page 79 SECTION 4 4.11 Parts List 446SD Power Unit PARTS ITEM PART NO. DESCRIPTION 010002 FSTN, HHCS 1/4-20 X 3/4 010019 FSTN, HHCS 5/16-18 X 3/4 GR 5 010024 FSTN, HHCS 5/16-18 X 2 GR 5 010039 FSTN, HHCS 3/8-16 X 1 3/4" LONG GR5 010081 FSTN, FW 1/4 010089...
  • Page 80 4.11 Illustration 042037 SECTION 4 446SD Power Unit - cont’d PARTS 4-34 055561; 01/12...
  • Page 81 PLATE, WALKBEHIND LIFTING 053446 DECAL, MADE IN USA (SP) 053448 DECAL, LIFT HERE ONLY (SP) 053453 DECAL, SPARK WARNING (SP) 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 056341 DECAL ALLEN OVAL 2" X 3.34" WHITE (Continued from Page 4-33) 4-35 055561; 01/12...
  • Page 82 4.12 Illustration 055643 SECTION 4 446SD-TC Power Unit PARTS 4-36 055561; 01/12...
  • Page 83 4.12 Parts List SECTION 4 446SD-TC Power Unit PARTS ITEM PART NO. DESCRIPTION 010001 FSTN, HHCS 1/4-20 X 1/2 GR 5 012975 FSTN, HHCS 5/16-24 X 1 GR 5 010024 FSTN, HHCS 5/16-18 X 2 GR 5 010038 BOLT, 3/8-16x1-1/2 GR 5 HHCS 010045 FSTN, HHCS 3/8-16 X 3-1/4 010082...
  • Page 84 4.12 Illustration 055643 SECTION 4 446SD-TC Power Unit - cont’d PARTS 4-38 055561; 01/12...
  • Page 85 DRIVEN PULLEY 055902 BELT, CVT F/ TEXAS WALKER 055903 EXT RETAINING RING 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 056341 DECAL ALLEN OVAL 2" X 3.34" WHITE 056458 PULLEY GUARD 056459 RING, 446SD-TC 056484 HHCS, 5/16-24 X 4 1/2 058051...
  • Page 86 4.13 Illustration 015202 SECTION 4 Standard Gear Box PARTS Torque to 22 Ft. Lbs. Grease this area for re-assembly only. 4-40 055561; 01/12...
  • Page 87 Standard Gear Box PARTS ITEM PART # DESCRIPTION 001003 GREASE, MOBILITH SCH220 .094 048299 OIL, ALLEN ENGINEERING GEARBOX .757/LT 010498 PLUG, 3/8 NPT BI SQ HD PIPE 010513 FITTING, 1/4-28 NPT STR GREASE 012953 PLUG, 3/4 NPTF BI SQ HD PIPE 015204...
  • Page 88 SECTION 4 4.14 Illustration 055647 Gear Box w/ Special Shaft (TC) PARTS Torque to 22 Ft. Lbs. Grease this area for re-assembly only. 4-42 055561; 01/12...
  • Page 89 Gear Box w/ Special Shaft (TC) PARTS ITEM PART # DESCRIPTION 001003 GREASE, MOBILITH SCH220 .094 048299 OIL, ALLEN ENGINEERING GEARBOX .757/LT 010498 PLUG, 3/8 NPT BI SQ HD PIPE 010513 FITTING, 1/4-28 NPT STR GREASE 012953 PLUG, 3/4 NPTF BI SQ HD PIPE 015204...
  • Page 90 4.15 Illustration SECTION 4 Handle (Short, Fine) - 034284 PARTS See Page 4-4 for Fine Pitch Adjustment Assembly 4-44 055561; 01/12...
  • Page 91 INSULATION, F/ HANDLEBAR 034714 BRKT, WB SHORT HANDLE FOOT PAD MTG 048308 GRIP, HANDLE (7/8"ID) 048379 DECAL, ALLEN 4 1/2 x 1 1/2 048937 DECAL, MFG BY ALLEN ENGR 049770 COVER, WB HANDLE PAD (STRAIGHT) 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 4-45 055561;...
  • Page 92 SECTION 4 4.16 Illustration Handle (Short, Positive) - 034450 PARTS See Page 4-6 for Positive Pitch Adjustment Assembly 4-46 055561; 01/12...
  • Page 93 BRKT, WB SHORT HANDLE FOOT PAD MTG 036448 HANDLE, POS PITCH WELDMENT 048308 GRIP, HANDLE (7/8"ID) 048379 DECAL, ALLEN 4 1/2 x 1 1/2 048937 DECAL, MFG BY ALLEN ENGR 049770 COVER, WB HANDLE PAD (STRAIGHT) 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 4-47 055561;...
  • Page 94 SECTION 4 4.17 Illustration Handle (Long, Fine) - 034283 PARTS See Page 4-4 for Fine Pitch Adjustment Assembly 4-48 055561; 01/12...
  • Page 95 INSULATION, F/ HANDLEBAR 034714 BRKT, WB SHORT HANDLE FOOT PAD MTG 048308 GRIP, HANDLE (7/8"ID) 048379 DECAL, ALLEN 4 1/2 x 1 1/2 048937 DECAL, MFG BY ALLEN ENGR 049770 COVER, WB HANDLE PAD (STRAIGHT) 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 4-49 055561;...
  • Page 96 SECTION 4 4.18 Illustration Handle (Long, Positive) - 034451 PARTS See Page 4-6 for Positive Pitch Adjustment Assembly 4-50 055561; 01/12...
  • Page 97 BRKT, WB SHORT HANDLE FOOT PAD MTG 036448 HANDLE, POS PITCH WELDMENT 048308 GRIP, HANDLE (7/8"ID) 048379 DECAL, ALLEN 4 1/2 x 1 1/2 048937 DECAL, MFG BY ALLEN ENGR 049770 COVER, WB HANDLE PAD (STRAIGHT) 056336 DECAL AEC 1.5" X 3.25" WHITE/RED 4-51 055561;...
  • Page 98 SECTION 4 4.19 Illustration Handle (Short, Fine) - 055638 PARTS See Page 4-4 for Fine Pitch Adjustment Assembly 4-52 055561; 01/12...
  • Page 99 EXTENSION WDMT F/SHT HNDL F/PT 034714 BRKT, WB SHORT HANDLE FOOT PAD MTG 048308 GRIP, HANDLE (7/8"ID) 048379 DECAL, ALLEN 4 1/2 x 1 1/2 048937 DECAL, MFG BY ALLEN ENGR 055636 CONTROL LEVER, E-KILL 055636 LEVER, CONTROL F/ DIESEL W/B 056336 DECAL AEC 1.5"...

  • Page 100: Safety Switch Assembly

    SECTION 4 4.20 Illustration Safety Switch Assembly - 018409 PARTS 4-54 055561; 01/12...
  • Page 101 SECTION 4 4.20 Parts List Safety Switch Assembly PARTS ITEM PART NO. DESCRIPTION 013370 FSTN, RHMS 10-32 X 3/8 013704 FSTN, LW EXT STAR 8-32 016137 TERMINAL, #10 14-16 GA RING 018264 INSULATOR RUBBER SAFETY SWITCH 018267 CLIP CONTACT - PT SAFETY SWTCH 018324 HOUSIN SAFETY SWITCH MF 018326...
  • Page 102 SECTION 4 Notes PARTS 4-56 055561; 01/12...
  • Page 103 INTENTIONALLY BLANK 055561; 01/12...
  • Page 104 YOUR TOTAL SOURCE FOR CONCRETE EQUIPMENT 055561; 01/12...

Table of Contents