Insignia NS-BK2TBK8 Quick Setup Manual

QUICK SETUP GUIDE
2-Tap Beverage
Cooler / Kegerator
NS-BK2TBS8 / NS-BK2TBK8
Congratulations on your purchase! Your NS-BK2TBS8 / NS-BK2TBK8 kegerator
is designed for years of fun and trouble-free performance. This Quick Setup
Guide is provided to help you get your kegerator up and running quickly. If
you need more help, however, take a look at the online manual, located at
www.insigniaproducts.com.
PACKAGE CONTENTS
Adjust Change
temperature temperature unit
Display
Quick Cool
1 Beer tap handles (2) 13 Beer keg (not included)
2 Draft arm assembly 14 Metal washers for locking casters (2)
3 Guard rail 15 Locking casters (2)
4 Drip tray (2 pieces) 16 Beer gasket with screws (4)
5 Worktop 17 Hose clamp
6 Control Panel 18 CO back tank retainer
2
7 Sankey Type-D keg coupler (2) 19 Extra valve washers (2 of each)
8 CO tank regulator 20 Wire shelf
2
9 5 lb. CO tank (shipped empty) 21 Wire half-shelf
2
10 Bolt and nut for retainer 22 Metal wrench (for cleaning)
11 CO tank retainer 23 Casters (2)
2
12 CO gas lines
2
Before using your new product, please read these instructions to prevent any damage.
Before assembly
Fill the CO
2
See your local beer keg
provider, air/gas or
welding supplier, or
sporting goods store.
Find a suitable location
Position the kegerator away from direct
sunlight and sources of heat, and avoid
positioning the kegerator in moist areas.
Assembling your kegerator
1
INSTALLING THE CASTERS (OPTIONAL)
1 Tip the kegerator onto its side on a soft surface to protect it from
scratches.
2 Unscrew and remove the black front feet. Keep them in a safe place in
case you want to use the feet later.
3 Attach the two metal washers (included) to the locking casters to
prevent scratching the cabinet, then install the two locking casters in the
front positions on the bottom of the kegerator (closest to the door).
4 Install the other two casters in the rear positions on the bottom of the
kegerator.
Quick cool
Quick Cool
5 With all four casters tightened evenly, stand the unit in the upright
position.
6 Step on the front of the locking casters to lock the kegerator into place
or step on the back to unlock the kegerator.
2
ATTACHING THE GUARD RAIL
Place the guard rail into the holes on the top of the kegerator.
Do not use an
tank Allow for space
extension cord
Make sure that there
3"
is 3" between the
back and sides of the
kegerator and any
surrounding walls.
You will need
Pliers/
clamp crimper
Full kegs of beer
Phillips Adjustable
screwdriver
Wrench
Front
Metal washers
Locking casters
Casters
3
INSTALLING THE DRAFT ARM ASSEMBLY
1 Remove the cabinet plug from the top of the kegerator.
2 Align the beer gasket to the four holes on the top of the cabinet.
3 Pass both the wing nut and the beer tube (both are attached to the
draft arm assembly) through the hole on the worktop until the draft
arm assembly is resting on the top of the cabinet.
4 Align the holes in the draft arm with the holes in the gasket, then
attach the draft arm to the worktop with the four screws provided.
5 Attach the black plastic beer tap handles to the top of the faucet,
tightening by hand. Hold the silver ring snug so it does not move.
(1/2 barrel size
or smaller)
4
INSTALLING THE CO REGULATOR & TANK
2
Note: The CO tank (provided) is empty when you receive it. Visit your local beer keg
2
provider, air/gas or welding supplier, or sporting goods store to get it filled.
Caution: Before installing the CO
the manual.
1 Feed the hose clamp over one end of the CO
2 Attach that end to the gas line connector on the CO
Shut-off valve
Hose clamp
CO gas lines
2
3 Tighten the clamp to prevent leaks. Leave about ½ inch between the
top of the clamp and the end of the hose. You may need to squeeze
with a pliers or crimper.
4 Attach the CO regulator to the CO
2
nut onto the tank valve and tightening with an adjustable wrench.
Tank Regulator
valve nut
5 Slide the CO tank through the retainer inside the kegerator and
2
secure it with the bolt and nut. Position the tank so that you can read
the numbers on the gauge and have easy access to the shut-off valve.
OR
Install the CO tank retainer on the back of the kegerator for extra
2
space inside the unit. Refer to the manual for additional information.
Beer tap handles
Draft arm assembly
Wing nut and beer tube
Beer gasket screws
Beer gasket
Cool
Quick
regulator and tank, review important safety tips in
2
gas line.
2
regulator.
2
CO tank regulator
2
Sankey keg couplers
tank by screwing the regulator
2