Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Samsung MF68-00271A
Summary of Contents for Samsung MF68-00271A
-
Page 1: Digital Terrestrial Receiver
MF68-00271A DIGITAL TERRESTRIAL RECEIVER... - Page 2 DTB-9401F Instructions for use REV. 1.1 DIGITAL TERRESTRIAL RECEIVER...
-
Page 3: Safety Instructions
SAFETY INSTRUCTIONS This STB has been manufactured to satisfy international safety standards. Please read the following recommended safety precautions carefully. MAINS SUPPLY AC 100~240V 50/60Hz OVERLOADING Do not overload wall outlets, extension cords or adapters as this can result in fire or electrical shock. LIQUIDS Keep liquids away from the STB. - Page 4 WARNING! 1. Follow these directions in order not to damage the power cord or plug. " Do not modify or process the power cord or plug arbitrarily. " Do not bend or twist the power cord too much. " Make sure to disconnect the power cord with holding the plug. "...
-
Page 5: Table Of Contents
CONTENT Safety Instructions ........2 General Features . -
Page 6: General Features
1. USER SECTION 2. TUNER SECTION 3. VIDEO SECTION 4. AUDIO SECTION GENERAL FEATURES 400 PROGRAMMABLE CHANNELS ADVANCED ELECTRONIC PROGRAM GUIDE MULTI LANGUAGE SUPPORTED FOR OSD SUBTITLE & TELETEXT(OSD & VBI) SUPPORTED WITH MULTI LANGUAGE FULL FUNCTION INFRARED REMOTE CONTROL UNIT AUTO AND MANUAL SCAN FACILITY CHANNEL ORGANIZING (PROGRAMMABLE) LOW POWER CONSUMPTION... -
Page 7: Connecting Your Dtb-9401F
CONNECTING YOUR “DTB-9401F” 1. LOCATION OF THE RECEIVER Your DTB-9401F should be placed under proper ventilation. Don’t put in completely enclosed cabinet that will restrict the flow of air, resulting in overheating. The location should be safeguarded from direct sunlight, excess moisture, rough handling or household pets. - Page 8 CONNECTING YOUR “DTB-9401F” Connecting Figure N N o o t t e e : In some region, the digital terrestrial signal may be weak. So you’d better use the antenna in which the booster was built, for watching the weak signal channels. GB-7...
-
Page 9: Description
Front Panel 1. Infrared Sensor This is to receive the IR commands from the Remote Control Unit. 2. LED When the LED light Red, the set-top box enters the standby mode. When the LED light Green, it enters the operation mode. DESCRIPTION GB-8... -
Page 10: Rear Panel
Rear Panel 1. AC MAINS 2. DIGITAL AUDIO OUT 3. AV2(EXT) 4. AVI(TV) 5. ANT. LOOP 6. ANT. IN DESCRIPTION This is to plug in the AC mains power cord. The input AC voltage range is 100V to 240V, 50Hz/60Hz supply. Output for connection to a digital amplifier. -
Page 11: Remote Control Unit
Remote Control Unit N N o o t t e e : When inserting batteries, make sure that the polarity(+/-) is correct. 1. POWER This is used to switch the receiver ON/STANDBY mode. 2. 0-9 Numerical keys These keys are to enter numeric values and to select the channel directly by entering its number. - Page 12 5. MUTE 6. FAV 7. EPG 8. LAST 9. TEXT(green) 10. ALT(yellow) 11. AUDIO(blue) 12. INFORMATION (red) 13. MENU 14. EXIT 15. OK 16. CH+/CH- 17. VOL+/VOL- DESCRIPTION This key is used to toggle between normal & muted audio. Use the key to switch between favorite lists. Electronic Program Guide button displays the TV/Radio Program guide.
-
Page 13: Basic Functions
1. Display Screen Before you can view the television program, you must perform the installation. Therefore you will see only menu images at first. After the television channels have been programmed, you will see the following picture(banner) each time you switch channels: Channel Number Signal Status Program Information... - Page 14 3. Select Soundtrack Press the ALT(yellow) key to see the soundtrack list. Press the and OK key to select one. 4. Select Videotrack Press the ALT(yellow) key twice to see the videotrack list. Press the and OK key to select one. 5.
- Page 15 5.1 Service Favorites Press the green(TEXT) key on the control unit to select the Favorites list. Press the green(TEXT) key to toggle group and channel list. Use the / , Pg+/Pg- keys to select a favorite group that you want. 5.2 Service Alphabetical Press the yellow(ALT) key on the remote control unit to select the Alphabetical list.
- Page 16 6. Program Information EPG-Electronic Program Guide The electronic program guide gives you a channel list for the channels. N N o o t t e e : 1. This service depends on service provider. 2. After receiver recognized the GMT-time from the signal which takes few seconds, it can display correct EPG information.
- Page 17 8. Teletext OSD When the current broadcasting program provides Teletext OSD, press the TEXT key twice to see the current Teletext OSD list. To change the Teletext OSD: Use the keys to select a Teletext OSD you want. Press the OK key and then the Teletext OSD you want is displayed on the screen.
-
Page 18: Operating The Receiver
Main Menu After installing your antenna system and DTB-9401F with appropriate connectors. Plug in the AC main power and switch on the receiver. Press the MENU key to bring up the main menu. The following on screen display will appear: The sub menu topics will be displayed from 1 to 4. -
Page 19: Manual Scanning
1.1 Manual Scanning To tune-in new channels and weak signals, the DTB-9401F has been provided with the option “Manual Scanning” where the channel data can be entered by the user. After selecting the “Manual Scanning” from the Installation Menu, the following screen will be displayed: Select the channel which you want to find. -
Page 20: Auto Scanning
1.2 Auto Scanning The sub menu “Auto Scanning” will enable download of the channels automatically from the preprogrammed load. To download channels automatically: Select the region which is possible in your location for Auto search. You can select All or Only Free option mode. All : Scanning all the channels Only Free : Scanning free channels Select the FFT (Fast Fourier Transform) Mode. -
Page 21: Channel Organising
2. Channel Organising The “Channel Organising” menu has six functions: The “Channel Organising” menu is used to delete the Frequencies and Channels or to make Favorite channels or move channel as you want. Enter the PIN Code. If you have not entered your own PIN Code PIN Code 0000 applies, which was set at the factory. -
Page 22: Delete All Channels
2.3 Delete All Channels At the request window, press the OK key to delete all channels and press the MENU / EXIT to exit. 2.4 Delete Scrambled Channels At the request window, press the OK key to delete scrambled channels and press the MENU / EXIT to exit. 2.5 Favorite Channels You can immediately register the present channel to the desired Favorite Group. -
Page 23: Move & Edit Channel
2.6 Move & Edit Channel Select the TV/RADIO list with Select the TV/RADIO list with Select channel by pressing the red( i ) key. Press the or Pg+/Pg- keys to change the position of the channel you want, and press the OK key for confirmation. -
Page 24: Parental Lock
3. Parental Lock This “Parental Lock” feature sets viewing restrictions and prevents unauthorized access to your DTB-9401F through the PIN (Personal Identification Number), which is a 4 digit number. (The factory preset PIN Code : 0000) On selecting this menu, you will have two options: to set lock for any desired channel and to change your PIN value. -
Page 25: Change Pin Code
OPERATING THE RECEIVER 3.2 Change PIN Code To change the PIN Code, select the second option “Change PIN Code”. This will take you to the following menu: In this option, you need to enter the current PIN Code at the first cursor, and at the second cursor enter the desired PIN Code. -
Page 26: System Setup
4. System Setup This option enables you to change the factory preset system settings as per your requirements. 4.1 Language Selection The “Language Selection” option allows the user to select the desired language of the OSD, Soundtrack, Teletext, Subtitle or EPG. To accommodate user from different regions speaking different languages, OSD languages are available 18 languages. -
Page 27: Media Settings
4.3 Media Settings You can set the various media settings you want. Place the cursor on this sub menu and press the OK key. Press the keys to move the sub items and press the keys to select the option. Press the OK key to confirm. -
Page 28: System Information
OPERATING THE RECEIVER 4.5 System Information If you have to contact your service provider or a service center they might ask for information available from this menu. Place the cursor on this sub menu and press the OK key. The following will be the on-screen display. 4.6 Software Upgrade You can download and upgrade the system software of the receiver through a specific channel through a specific channel designated by the broadcaster. -
Page 29: Troubleshooting
TROUBLESHOOTING In some region, the digital terrestrial signal may be weak. So you’d better use the antenna in which the booster was built, for watching the weak sinal channels. You can download and upgrade the system software of the receiver through a specific channel through a specific channel designated by the broadcaster. -
Page 30: Technical Specifications
TECHNICAL SPECIFICATIONS Power supply Type : Input Voltage : Fuse rating : Power Consumption : Stand by : Demodulator Type : FFT : Code Rate : Guard Intervals : RF Input Input Connector : Frequency range : Input Signaln Level : Loop Through : Video decoder System decoding :... - Page 31 TECHNICAL SPECIFICATIONS BASE-BAND AUDIO/VIDEO OUTPUT VIDEO Video Type : Interface : Impedance : Output level : AUDIO Inteface : Impedance : Output level : Frequency response : DIGITAL AUDIO (S/PDIF) : MEMORY Flash : SDRAM : PHISICAL SPECIFICATION Size (W x D x H) : Weight (Net) : PAL, SECAM 2 SCART (TV, VCR)
- Page 32 MEMO GB-31...
- Page 33 MEMO...
- Page 34 MEMO...