PROHIBITED Do not pull the cable to unplug. • This can damage the cable, which is the origin of a fire or a breakdown of the printer. PROHIBITED Do not plug in or unplug with your hands wet. • You can be electrocuted.
Page 3
• After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG PRINTER Install the printer on the stable surface. • If the printer falls down, it can be broken and you can hurt yourself. PRINTER PROHIBITED Do not let water or other foreign objects in the printer.
Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or remove the cables on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF”.
Page 5
SRP-350/352plusA&C ■ Introduction The SRP-350/352plus Roll Printer are designed for use with electronic instruments such as system ECR, POS, banking equipment, computer peripheral equipment, etc. The main features of the printer are as follows: 1. High speed printing : 47/52 (1/6” Feed) lines per second.
SRP-350/352plusA&C 1. Setting Up the Printer 1-1 Unpacking Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. SRP-350/352plusC SRP-350/352plusA Cover Cable Roll Paper Manual AC Adapter Power Cord USB A-A CABLE - 7 - Rev.
1-2 Connecting the Cables You can connect up the three cables to the printer. They all connect to the connector panel on the back of the printer, which is shown below: ※ NOTE Before connecting any of the cables, make sure that both the printer and the host are turned off.
Do not connect a telephone line to the drawer kick-out connector; otherwise the printer and the telephone line may be damaged. Plug the drawer cable into the drawer kick-out connector on the back of the printer next to the power supply connector.
1-4 Setting the Dip Switches 1-4-1 Serial Interface (RS-232C) • DIP Switch 1 Function Auto Line Feed Handshaking Data Length Parity Check Parity Selection Baud Rate Selection (bps) • DIP Switch 2 Function Reserved Internal bell control Auto Cutter BUSY Condition Print Density Near-End Sensor Status 1-4-2 Parallel &...
The Memory Switch is available to be changed by three methods. - Memory Switch setting utility. - Control from ESC/POS command. Settings of the Memory Switch are stored in the NV memory : therefore, even if the printer is turned off, the settings are maintained. MSW1...
Page 14
MSW2-8 MSW2-7 MSW2-6 MSW2-5 MSW2-4 MSW2-3 Character Table MSW8 Switch Function Reserved MSW9 Switch Function Reserved MSW10 (Special Function 1) Switch Function External buzzer control (This functions operate only after cutting) Reserved Printing width 2Color support Reserved MSW11 (Special Function 2) Switch Function Reserved...
1-6-2 Open the paper roll cover by pressing the cover-open button. ※ NOTE Do not open the print cover while the printer is operating. This may damage the printer. 1-6-3 Remove the used paper roll core if there is one.
Page 16
1-6-5 Be sure to note the correct direction that the paper comes off the roll. 1-6-6 Pull out a small amount of paper, as shown. Then close the cover. ※ NOTE When closing the cover, press the center of printer cover firmly to prevent paper miss-loading. 1-6-7 Tear off the paper as shown.
○ PAPER This light indicates the near end of the paper roll. Install a new paper roll and the printer Will continue printing. When the light blinks, it indicates the self-test printing standby state or macro execution Standby state when the macro execution command is used.
Do not plug in the power cord. Otherwise, you may damage the power supply or the printer. 1-10-1 Make sure that the printer’s power switch is turned off, and the power supply’s power cord is unplugged from the electrical outlet.
2. Self test The self-test checks whether the printer has any problems. If the printer does not function properly, contact your dealer. The self-test checks the following; 2-1 Make sure paper roll has been installed properly. 2-2 Turn on the power while holding down the FEED button. The self-test begins.
3-3 Close the cover, then the printer enters the hexadecimal dump mode. 3-4 Run any software program that sends data to the printer. The printer will print all the codes it receives in a two-column format. The first column contains the hexadecimal codes and the second column gives the ASCII characters that corresponds to the codes.
4. Specification Item Printing Method Dot Density Printing Width Characters per line (Default) Printing Speed *1) Receive Buffer Size Printer SMPS Input Voltage Frequency SMPS Output Voltage Temperature Humidity Auto Cutter Mechanism MCBF *2) Paper Type Roll Width Roll Diameter...
SRP-350/352plusA&C 5. Appendix 5-1 Cleaning Printer Paper dust inside the printer may lower the print quality. In this case clean the printer as follows. 5-1-1 Open the printer cover and remove the paper if exists. 5-1-2 Clean the print head with a cotton swab moistened with alcohol solvent.