Subscribe to Our Youtube Channel
Related Manuals for Trotec TWP 4025 E
Summary of Contents for Trotec TWP 4025 E
- Page 1 TWP 4025 E / TWP 7025 E / TWP 11025 E OPERATING MANUAL SUBMERGED WASTE WATER PUMP...
-
Page 2: Table Of Contents
Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the operating manual must be observed. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... -
Page 3: Safety
• Have all electrical installations carried out by an expert according to the national regulations and the device- specific requirements. • Do not use the power cable to drag the device. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... - Page 4 • After the set-up of the device, its mains plug must be readily accessible during operation. • Wear sturdy shoes to protect yourself against electric shock. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E...
- Page 5 Safety chapter. Allow the device to cool down and switch it off. Investigate the cause of overheating. Should the problem persist, please contact the customer service. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E...
-
Page 6: Information About The Device
Transport handle / attachment for nylon cord Power cable Float switch locking device Float switch Air intake opening with cover panel and impeller Connection with 1 ½" internal thread Reducer Elbow submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... -
Page 7: Transport And Storage
• Please note that the conveying capacity declines with an increasing length of the water discharge line. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... - Page 8 Slide an appropriate hose clamp onto the hose. 4. Push the hose (inner diameter 25 mm or 32 mm) onto the reducer (7) all the way to the stop. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E...
- Page 9 Warning of electrical voltage Electric shock from damaged power supply cable. Make sure not to hold or suspend the device by the power supply cable under any circumstances. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E...
-
Page 10: Operation
4. Attach the nylon cord to an easily accessible position, so you can pull the device back out after pumping has been completed. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... - Page 11 1. Hold onto the mains plug while pulling the power cable out of the mains socket. 2. If necessary, pull the device out by means of the nylon cord. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E...
-
Page 12: Errors And Faults
• Check whether the used hose diameter is too small. • Check whether the hose line is kinked or blocked. Remove kinks and / or blockages. • Check reducer (7) and / or elbow (8) for blockages. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... -
Page 13: Maintenance
Inside the device, there are no parts that need to be maintained means of a jet of water. or lubricated by the user. • Reattach the cover panel to the device. submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... -
Page 14: Technical Annex
180 mm Hose connection, inner diameter 25 mm; 32 mm 25 mm; 32 mm 25 mm; 32 mm Threaded connection 1"; 1 ½" 1"; 1 ½" 1"; 1 ½" submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E... - Page 15 6.000 9.000 TWP 7025 E TWP 7025 E max. 35 °C 3.000 6.000 9.000 12.000 TWP 11025 E TWP 7025 E TWP 11025 E 3.000 6.000 9.000 12.000 15.000 max. 35° TWP 11025E submerged waste water pump TWP 4025 E / TWP 7025 E / TWP 11025 E...
-
Page 16: Disposal
TWP 4025 E / TWP 7025 E / TWP 11025 E... - Page 17 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...
Need help?
Do you have a question about the TWP 4025 E and is the answer not in the manual?
Questions and answers