Brbk-301 (An-22 Board) Circuit Description; Brbk-302 (Sd-50 Board) Circuit Description - Sony BRC-300 Service Manual
3ccd color video camera / optical multiplex unit
Hide thumbs
Also See for BRC-300:
- Command list (23 pages) ,
- Specifications (8 pages) ,
- Brochure & specs (8 pages)
Table of Contents
Advertisement
5-4. BRBK-301 (AN-22 Board) Circuit
Description
The BRBK-301 is installed in BRC-300/300P or BRU-
300/300P to output analog GBR/YCbCr/SYNC signals and
analog composite/YC signals to the 9-pin D-sub connector.
Analog GBR/YCbCr/SYNC Signals
The 8-bit Y data and CbCr data sent from BRC-300/300P
or BRU-300/300P are latched by the 13.5 MHz clock and
6.75 MHz clock, and then separated into 8-bit Y/Cb/Cr
data of the same timing. These data are converted to analog
Y/Cb/Cr signals by D/A converters IC7011, IC7012 and
IC7013, and then decoded to analog G/B/R signals by
IC7016, IC7017 and IC7018.
Selectors IC7024, IC7025 and IC7026 select either one of
the analog Y/Cb/Cr signals or analog G/B/R signals. A
sync signal is added to the Y signal or G/B/R signals by
IC7028, IC7029 and IC7030. The Y signal or G/B/R
signals are then output to the D-sub connector. It is also
possible to output G/B/R signals without sync signal. The
sync signal is the C SYNC signal sent from BRC-300/300P
or BRU-300/300P, which is also output to the D-sub
connector.
Analog VBS/YC Signals
The 8-bit Y data and CbCr data sent from BRC-300/300P
or BRU-300/300P are input into the digital encoder
IC7022.
The digital encoder encodes the Y and CbCr data to the
composite signal and Y/C signals using the 27 MHz clock
and H SYNC/V SYNC signals, and then converts the
digital signals to analog composite signals and Y/C signals.
Either one of the analog composite signal or analog Y/C
signals is selected by the selectors IC7032 and IC7033, and
then output to the D-sub connector.
Output Signal Selection and Level Adjustment
The serial data CSO sent from BRC-300/300P or BRU-
300/300P is D/A converted by EVR IC7015 to restore
selection signals and level adjustment signals. These
signals are used for selection of analog output signals and
for level adjustment.
Power Supply Circuit
The DC-DC converter generates +3.3 V DC and _3.3 V
DC from the +12 V supplied by BRC-300/300P or BRU-
300/300P.
5-5. BRBK-302 (SD-50 Board) Circuit
Description
The BRBK-302 is installed in BRC-300/300P or BRU-
300/300P to output the SDI signal.
The 8-bit Y data and CbCr data sent from BRC-300/300P
or BRU-300/300P are multiplexed by IC8003. Synchroniz-
ing data is also added based on the FLD, VD and HD
signals. The multiplexed data is then converted to SDI
serial data by IC8006, and then output to external equip-
ments with the output drivers Q8006 and Q8007.
The flash memory IC8005 retains the configuration data of
the FPGA IC8003.
The DC-DC converter generates +3.3 V DC and +5 V DC
from the +12 V supplied by BRC-300/300P or BRU-300/
300P. Further, the series regulator generates +1.5 V DC
from the +3.3 V.
BRC-300/300P
5-6
Hide quick links:
Advertisement
Table of Contents
