Download Print this page

Cisco HPNA Quick Reference Manual

Digistar ethernet over coax aggregation point (ap).
Hide thumbs
   

Advertisement

HPNA Module
for DigiStar Ethernet over Coax Aggregation Point (AP)
Introduction
This installation quick reference is intended for individuals responsible for installing the
HPNA module for the DigiStar Ethernet over Coax Aggregation Point (AP). For complete
information about Safety Instructions, Installation and Operation, see the DigiStar Ethernet
over Coax (EoC) Aggregation Point (AP) E230 Installation and Operation Guide, part
number 4040978.
NOTE
Power off the AP before removing or installing the HPNA module. Hot swapping the
HPNA module may damage the AP and HPNA module.
Do not force the HPNA module connector into the main board connector. It may damage
the connectors on the HPNA module and the main board.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the
U.S. and other countries. A listing of Cisco's trademarks can be found at
www.cisco.com/go/trademarks.
Third party trademarks mentioned are the property of their respective owners. The use of the word
partner does not imply a partnership relationship between Cisco and any other company. (1009R)
Specifications and product availability are subject to change without notice.
 2011 Cisco and/or its affiliates. All rights reserved.
Cisco Systems Inc.
800 722-2009 or 678 277-1120
www.cisco.com
Quick Reference Guide
HPNA Module Installation
Module 1 Installation
Follow the instructions below to install HPNA
module 1.
1.
2.
3.
4.
5.
6.
7.
Part Number 4042738 Rev A
Number 7019941 Rev A
October 2011
February 2010
Power off the AP.
Place module 1 in a vertical position and
align its Front Surface with Edge A of the
white cover as shown on the right.
Insert the two module screws into the
screw holes and the single guide hole.
Gently adjust the module to align and
guide the module connector into the
main board connector.
Gently press module 1 and confirm that
the module connector is inserted
completely into the main board
connector.
Do not force the module connector into
the main board connector. Repeat steps
4-5 if you find it difficult to insert the
module connector into the main board
connector.
Tighten the two module screws with a
flat tip driver from 0.39 Nm to 0.98 Nm.
Module 1 Installation
Module 2 Installation
Follow the instructions below to install HPNA
module 2.
1.
Power off the AP.
2.
Place module 2 in a vertical position and
align its Back Surface with Edge B of the
white cover as shown below.
3.
Insert the two module screws into the
screw holes.
4.
Gently adjust the module to align and
guide the module connector into the
main board connector.
5.
Gently press module 2 and confirm that
the module connector is inserted
completely into the main board
connector.
6.
Do not force the module connector into
the main board connector. Repeat steps
4-5 if you find it difficult to insert the
module connector into the main board
connector.
7.
Tighten the two module screws with a
flat tip driver from 0.39 Nm to 0.98 Nm.
Module 2 Installation

Advertisement

   Related Manuals for Cisco HPNA

   Summary of Contents for Cisco HPNA

  • Page 1

    HPNA module and the main board. Module 2 Installation Module 1 Installation Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.

  • Page 2

    0.98 Nm 的扭力拧紧 2 个模块螺 模块的人员参考。如需获得更多关于安全、安装和操作的信息,可参考 DigiStar 以 丝。 太网同轴网络 (EoC) 局端设备 (AP) E230 安装与操作手册,部件号 4040979。 注意 卸下或安装 HPNA 模块之前请关闭 AP 的电源。热插拔 HPNA 模块可能会损坏 AP 主板 和 HPNA 模块。 请勿强行将 HPNA 模块连接器插入主板连接器。它可能会损坏 HPNA 模块上的连接器以 及主板上的连接器。 模块 1 安装 Cisco 和 Cisco 徽标是 Cisco 和/或其子公司在美国和其他国家/地区的注册商标或商标。 以下网址详细记...

Comments to this Manuals

Symbols: 0
Latest comments: