Page 1: Lcd Display
SyncMaster 400UX-2, 400UXN-2, 460UX-2, 460UXN-2 LCD Display User Manual...
Page 2: Safety Instructions
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property dam- age. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Page 3: Installation
Ensure that the power plug is plugged into the power outlet firmly and correctly. • Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Do not connect multiple appliances to the same power outlet. •...
Page 4 Keep heating appliances as far away from the power cord or the product as possible. • Do not install it in a badly ventilated location such as a bookcase or closet. • When putting the product down, make sure to put it down softly. •...
Page 5 When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • When cleaning the product, make sure to disconnect the power cord. • When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. •...
Page 6 Safety Instructions If thunder or lightning is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable.
Page 7 Safety Instructions To avoid eyestrain, do not sit too close to the product. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
Page 8 Safety Instructions The batteries (and rechargeable batteries) are not ordinary re- fuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
Page 9 Safety Instructions Do not put any heavy objects on the product. • This may result in personal injury and/or damage to the prod- uct.
Page 10: Checking The Contents Of The Package
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the grooves on both sides of the package...
Page 11 Manuals Quick Setup Guide (Not available in all loca- MagicInfo Software CD, MagicInfo Manual CD (Applicable to the UXN-2 model only) Cables Power Cord Others Remote Control Batteries (AAA X 2) (BP59-00138A) (Not available in all loca- Sold separately D-Sub Cable Introduction Warranty Card User's Guide...
Page 12 Sold separately Wall Mount KIT RGB to Component Cable Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values.
Page 13 SOURCE button [SOURCE] Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] → [DVI] → [AV] → [Component] → [HDMI] → [MagicInfo] Note • The BNC mode will not be activated on the UXN-2 model. •...
Page 14 Introduction Note Applicable to the UX-2 model only. Applicable to the UXN-2 model only. POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB/COMPONENT IN (PC/COMPO-...
Page 15 Introduction DVI IN (PC Video Connection Terminal) Use a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) DVI/RGB/HDMI AUDIO IN (PC/DVI/ HDMI(PC) Audio Connection Terminal (In- put)) AV/COMPONENT AUDIO IN [L- AUDIO- Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [ L- AUDIO - R ] port of the LCD Display.
Page 16 Introduction your digital output device using a HDMI ca- ble. Up to HDMI cable 1.0 can be supported. BNC OUT [R, G, B, H, V] (BNC Terminal (Output)) BNC (Analog PC) Connection: connecting the R, G, B, H, V ports. The number of LCD Displays that can be connected to the loopout depends on the ca- bles, signal source, etc.
Page 17: Remote Control
Note See Connecting Cables for further information regarding cable connections. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequen- Introduction Keyboard / Mouse, Mass Storage Device Compatible.
Page 18 POWER 3. Number Buttons 4. DEL / GUIDE but- 5. + VOL - SOURCE D.MENU 8. TOOLS Introduction POWER Number Buttons / GUIDE button + VOL - SOURCE D.MENU TOOLS Up-Down Left-Right buttons INFO COLOR BUTTONS TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P MENU RETURN...
Page 19 9. Up-Down Left-Right but- tons INFO 11. COLOR BUTTONS TTX/MIX 13. MTS/DUAL ENTER/PRE-CH MUTE CH/P 17. TV MENU RETURN Introduction Moves from one menu item to another horizontally, vertically or adjusts selected menu values. Current picture information is displayed on the upper left corner of the screen.
Page 20 EXIT 21. MagicInfo Introduction Exits from the menu screen. MagicInfo Quick Launch Button.
Page 21: Connecting A Computer
Connections Connecting a Computer Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the contents under Adjusting Your LCD Display. There are several ways to connect the computer to the monitor.
Page 22 Connections Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the DVI port on the back of your LCD Display and the DVI port on the computer. Using the HDMI (digital) output on the graphics card. •...
Page 23: Connecting To Other Devices
Note • Turn on both your computer and the LCD Display. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Note • AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display.
Page 24 Connect the Video and [R-AUDIO-L] port of the DVD, VCR or DTV Set-Top Box to the Video and [R-AUDIO-L] LCD Display. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted. Select AV using the SOURCE . Connecting the BNC to BNC cable Connect the BNC/COMPONENT IN [R/Y, G/P port on the external device using the BNC to BNC cable.
Page 25 Connect a Component cable between the BNC/COMPONENT IN [R/Y, G/P on the LCD Display and the P Note • Select Component for the connection to a DVD player using the SOURCE button on the front of the LCD Display or on the remote control. •...
Page 26: Connecting To A Camcorder
Connecting to a Camcorder Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV/COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display . Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display .
Page 27: Connecting Using A Dvi Cable
Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI Cable Connect between the DVI OUT port on the LCD Display and the input port on another monitor using a DVI cable. Connect between the AUDIO OUT port on the LCD Display and the audio input port on another monitor using a stereo cable.
Page 28: Connecting A Dtv Set Top (Cable/Satellite) Box
Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the DVI / RGB /HDMI AUDIO IN terminal of the LCD Display.
Page 29: Connecting To An Audio System
Connect the RGB/COMPONENT IN ports on the monitor to the P set-top box using the Component/ D-sub cable. Connect a set of audio cables between the AV COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note •...
Page 30: Connecting A Usb Device
Connect the LAN cable. Note Applicable to the UXN-2 model only. Connecting a USB device Note • You can connect USB devices such as a mouse or keyboard. • Applicable to the UXN-2 model only. Connections...
Page 31: Using The Software
Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) Insert CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
Page 32: Installing The Monitor Driver (Manual)
Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System Insert your Manual CD into your CD-ROM drive.
Page 33 This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. Click "Update Driver..." in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Page 34 Using the Software Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. ® ® Microsoft Windows XP Operating System...
Page 35 Using the Software Insert CD into the CD-ROM drive. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced...". Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver..."...
Page 36 "OK" button. Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Click the "Close" button, then click the "OK" button continually.
Page 37 Using the Software 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver), then click the "Open"...
Page 38 Using the Software If you can see the "Digital Signature Not Found" window, then click the "Yes" button. Then click the "Finish" button and the "Close" button. ® ® Microsoft Windows Millennium Operating System Click "Start", "Setting", "Control Panel". Double click the "Display" icon. Select the "Settings"...
Page 39: Installation Problems
Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) Enter the model name of your monitor.
Page 40 Using the Software Uninstall The MDC program can be removed only by using the "Add or Remove Programs" option of ® the Windows Control Panel. Perform the following steps remove MDC. Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a pro- gram".
Page 41: Main Screen
Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Page 42: Port Selection
Main Icons Remocon Safety Lock Port Selection 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set.
Page 43: Power Control
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable.
Page 44 Info Grid shows some basic information necessary to Power Control. (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control.
Page 45: Input Source
Power Control allows controlling some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) (Mute On/Off) - Turns on/off the Mute function of the selected display.
Page 46 • PC Mode...
Page 47 Info Grid shows some basic information necessary to Input Source Control. - Changes the Input Source of the selected display to PC. - Changes the Input Source of the selected display to BNC. - Changes the Input Source of the selected display to DVI. - Changes the Input Source of the selected display to TV.
Page 48: Image Size
The Input Source Control feature is available only for the displays whose power status is ON. Image Size PC, BNC, DVI 1. Click Image Size of the main icons and the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control. ( Power Status) - Shows the power status of the current display.
Page 49 Image Size TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV 1. Click Image Size of the main icons and the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control.
Page 50 1. Click Time of the main icons and the Time Control screen appears. Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display.
Page 51: Pip Size
PIP Size 1. Click PIP of the main icons and the PIP control screen appears. Click Select All or use Check Box to select a display to control. Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use.
Page 52: Pip Source
PIP Source 1. Click PIP of the main icons and the PIP control screen appears. Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC.
Page 53 Settings Picture 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar.
Page 54: Picture Pc
- Adjusts the Color Tone for the selected display. 8) Color Temp - Adjusts the Color Temp for the selected display. 9) Brightness Sensor - Adjusts the Brightness Sensor for the selected display. 10) Dynamic Contrast - Adjusts the Dynamic Contrast for the selected display. The Input source of MagicInfo works only on MagicInfo model.
Page 55 2) Contrast - Adjusts Contrast of the selected display. 3) Brightness - Adjusts Brightness for the selected display. 4) Red - Adjusts red Color of the selected display. - Available only for NT. 5) Green - Adjusts green Color of the selected display. - Available only for NT.
Page 56 Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM."...
Page 57: Image Lock
Image Lock 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display.
Page 58 An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
Page 59: Video Wall
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
Page 60 Select a display from Display Selection. The place will be set up by pressing a number in the selected mode. The MDC program supplied by Samsung supports up to 5x5 LCD Displayes. 3) On / Off - Turns on/off the Video Wall function of the selected display.
Page 61: Troubleshooting
You may not operate this function in MagicInfo. The Input source of TV works only on TV model. The Maintenance Control function is available only for the displays where the power status is ON. Troubleshooting 1. The display you wish to control does not appear on the Power Control Info Grid - Check the connection of RS232C.
Page 62 2. Selected one display: Fetches and displays the settings value for the selected display. 3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of ID 1, fetches and displays the value of ID3. 4.
Page 63: Adjusting The Lcd Display
Adjusting the LCD Display Input Available Modes • PC / DVI / BNC • • Component • HDMI • MagicInfo Note • The BNC mode will not be activated on the UXN-2 model. • MagicInfo supports the UXN-2 model only. Source List MENU →...
Page 64 When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off/On) MENU → ENTER → Note •...
Page 65 • HDMI : PC / BNC Swap MENU → ENTER → Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. Size MENU →...
Page 66: Edit Name
→ → ENTER Adjusts the Transparency of PIP windows. • High • Medium • • Opaque Note • PIP turns off when the LCD Display is switched to an external source. • For PC and DVI, this is deactivated if the cable is disconnected. Edit Name MENU →...
Page 67 Picture [PC / DVI / BNC / MagicInfo Mode] Available Modes • PC / DVI / BNC • • Component • HDMI • MagicInfo Note • The BNC mode will not be activated on the UXN-2 model. • MagicInfo supports the UXN-2 model only. MagicBright MENU →...
Page 68 Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
Page 69 → → ENTER The color tones can be changed. (Not available when Dynamic Contrast is set to On.) Cool Normal Warm Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled.
Page 70 → , → ENTER Blue MENU → → ENTER → ENTER → → , → ENTER Color Temp. MENU → → ENTER → → , → ENTER Color Temp. is a measure of the 'warmth' of the image colors. (Not available when Dynamic Contrast is set to On.) Note This function is only enabled if the Color Tone is set to Off.
Page 71 → , → ENTER Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Position MENU → → ENTER → → → ENTER → → → ENTER Adjusts the screen location horizontally and vertically. Auto Adjustment MENU →...
Page 72 → → ENTER Selects either On or Off with the signal control. Signal Control MENU → → ENTER → → ENTER → → R-Gain MENU → → ENTER → → , → ENTER G-Gain MENU → → ENTER → → , →...
Page 73 MENU → → ENTER → → → , → ENTER Size MENU → → ENTER → → → ENTER The Size can be switched. 16:9 HDMI Black Level MENU → → ENTER → → → ENTER When watching with a DVD or set-top box connecting to the product via HDMI or DVI, image quality deterioration (black level, lower-quality contrast, lighter color tone, etc.) may occur depending on the connected external device.
Page 74 PIP Picture MENU → → ENTER → → → ENTER Adjusts the PIP Screen Settings. Note • Available Modes: PIP ON Contrast MENU → → ENTER → → → ENTER→ → , → ENTER Adjusts the Contrast of the PIP window on the screen. Brightness MENU →...
Page 75 Note Enabled only when the PIP input is selected in AV, HDMI or Component mode. Tint MENU → → ENTER → → → → → → → ENTER → → , → ENTER Adds a natural tone to the PIP window. Note Enabled only when the PIP input is selected in AV, HDMI or Component mode.
Page 76 Picture [ AV / HDMI / Component Mode] Available Modes • PC / DVI / BNC • • Component • HDMI • MagicInfo Note • The BNC mode will not be activated on the UXN-2 model. • MagicInfo supports the UXN-2 model only. Mode MENU →...
Page 77 Contrast MENU → → ENTER → → , → ENTER Adjusts the Contrast. Brightness MENU → → ENTER → → , → ENTER Adjusts the Brightness. Sharpness MENU → → ENTER → → , → ENTER Adjusts the picture Sharpness. Color MENU →...
Page 78: Color Temp
→ → ENTER The color tones can be changed. The individual Color components are also user adjustable. (Not available when Dynamic Contrast is set to On.) Cool2 Cool1 Normal Warm1 Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled.
Page 79 → → ENTER The Size can be switched. 16:9: Sets the picture to 16:9 wide mode. Zoom 1: Magnifies the size of the picture on the screen. Zoom 2: Magnifies the size of the picture more than Zoom 1. 4:3: Sets the picture to 4:3 normal mode. Screen Fit: Displays the input scenes as they are without any cutoff when HDMI 720p, 1080i, 1080p signals are input.
Page 80 → → ENTER When a DVD or set-top box is connected to your TV via HDMI or DVI, it may cause a deg- radation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Page 81 Adjusting the LCD Display Note • Available Modes: PIP ON Contrast MENU → → ENTER → → ENTER→ → , → ENTER Adjusts the Contrast of the PIP window on the screen. Brightness MENU → → ENTER → → → ENTER→ →...
Page 82 → , → ENTER Adds a natural tone to the PIP window. Note Enabled only when the PIP input is selected in AV, HDMI or Component mode. Oper- ates only if the video signal is NTSC. Dynamic Contrast MENU → →...
Page 83 • MagicInfo Note • The BNC mode will not be activated on the UXN-2 model. • MagicInfo supports the UXN-2 model only. Mode MENU → → → ENTER → → → ENTER The LCD Display has a built-in high fidelity stereo amplifier. Standard Selects Standard for the standard factory settings.
Page 84 → , → ENTER Emphasizes low frequency audio. Treble MENU → → → ENTER → → , → ENTER Emphasizes high frequency audio. Balance MENU → → → ENTER → → , → ENTER Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume MENU →...
Page 85 → → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround XT delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.
Page 86 → → ENTER When you use the product with it connecting to a Home theater, turn the Internal speakers off so you can listen to sound from the Home theater's (external) speakers. Internal Sound is outputted both from the Internal speaker and the External speakers, but the volume control is only available from the Internal speaker.
Page 87 Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. MENU → → → → ENTER → Clock Set MENU → → → → → , → ENTER Current Time Setting. Sleep Timer MENU →...
Page 88 → → ENTER Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically. Off Timer MENU → → → → ENTER → → → →...
Page 89 Safety Lock Change PIN MENU → → → → ENTER → → → [0 9] → [0 9] → [0 9] → [0 9] The password can be changed. Note The preset password for the LCD Display is "0000". Lock On MENU →...
Page 90 Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting. MENU →...
Page 91 Provides a full screen without any margins. Natural Displays a natural image with the original aspect ratio intact. Horizontal MENU → → → → ENTER → → → → ENTER → → → ENTER Sets how many parts the screen should be divided horizontally. Five adjustment levels: 1, 2, 3, 4, and 5.
Page 92 The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Divider. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time.
Page 93 Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical MENU → → → → ENTER → → ENTER → Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time MENU →...
Page 94 Mode MENU → → → → ENTER → → You can change the Safety Screen Type. Scroll Eraser Period MENU → → → → ENTER → → Use this function to set the execution period for each mode set in the timer. Time MENU →...
Page 95 • Mode-Bar, Eraser : 10~50 sec Scroll MENU → → → → ENTER → → This function helps to remove after-images on the screen by moving all the pixels on the LCD according to a pattern. Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.
Page 96: Resolution Select
→ → ENTER Select the brightness of the grey for the screen background. Light Dark Resolution Select MENU → → → → ENTER → → → → ENTER When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution.
Page 97 Power On Adjustment MENU → → → → ENTER → → → → ENTER Adjusts the Power On time for the screen. OSD Rotation MENU → → → → ENTER → → → → ENTER → → → ENTER OSD Rotate Landscape Portrait Reset...
Page 98 → , → ENTER Note Available in PC mode only Note The Reset function is not available when Video Wall is On. Color Reset MENU → → → → ENTER → → ENTER → → , → ENTER Multi Control Available Modes •...
Page 99: Available Modes
MENU → → → → → → [0~9] • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MagicInfo Available Modes •...
Page 100 • The preset password for the LCD Display is "000000". • The server program's Power-On option works only if the LCD Display's power is com- pletely shut off. Please make sure not to use the Power-On option when the LCD Display is in the process of shutting down since this may cause system errors on the LCD Display.
Page 101 Adjusting the LCD Display 2. Select TCP/IP - step 2 In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3.
Page 102 Adjusting the LCD Display You can select which rotation type will be applied to your device. 5. Setup Information Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop.
Page 103: Self-Test Feature Check
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check Turn off both your computer and the LCD Display. Unplug the video cable from the back of the computer. Turn on the LCD Display.
Page 104: Symptoms And Recommended Actions
• Do not use benzene, thinner or other flammable sub- stances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.)
Page 105: Problems Related To The Screen
Check if the signal cable between the computer and the LCD Display is securely con- nected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. The screen is blank and the power indicator is off. Ensure that the power cord is firmly connected and the LCD Display is on.
Page 106: Problems Related To Audio
The screen color is inconsistent. Adjust color using Custom under OSD Color Adjustment menu. The color image is distorted by dark shadows. Adjust color using Custom under OSD Color Adjustment menu. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The Power Indicator blinks.
Page 107 Check if the batteries are empty. Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity. Q & A How can I change the frequency? The frequency can be changed by reconfiguring the video card.
Page 108 Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the In- formation section or contact your dealer.
Page 109: Specifications
Specifications General General Model Name LCD Panel Size SyncMaster 400UX-2, 400UXN-2 SyncMaster 460UX-2, 460UXN-2 Display area SyncMaster 400UX-2, 400UXN-2 SyncMaster 460UX-2, 460UXN-2 Pixel Pitch SyncMaster 400UX-2, 400UXN-2 SyncMaster 460UX-2, 460UXN-2 Synchronization Horizontal Vertical Display Color 16.7 M Resolution Optimum resolu- 1920 x 1080 @ 60 Hz tion Maximum resolu-...
Page 110 Maximum Pixel Clock 148.5MHz (Analog,Digital) Power Supply This product supports 100-240 V. Since the standard voltage may differ from country to country, please check the label on the back of the product. Signal connectors D-sub, DVI-D, AV(Composite,CVBS), HDMI, RS232C In/Out,PC Audio(Stereo) In, Audio Out , DVI OUT, LAN, USB(3port), VGA OUT (With Network model), Com- ponent / BNC (Without Network model) Dimensions (W x H x D) / Weight...
Page 111: Preset Timing Modes
Dot Acceptable black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800. Note Design and specifications are subject to change without prior notice. Note •...
Page 112 Specifications Display Mode Horizontal Frequency (kHz) IBM, 640 x 480 31.469 IBM, 720 x 400 31.469 MAC, 640 x 480 35.000 MAC, 832 x 624 49.726 MAC, 1152 x 870 68.681 VESA, 640 x 480 37.861 VESA, 640 x 480 37.500 VESA, 800 x 600 35.156...
Page 113: For Better Display
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT- LCD.
Page 114 Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. •...
Page 115: Select Method
• Avoid using a combination of characters and background color with large dif- ference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically •...
Page 116 • Time Period : 1 ~ 5 seconds ( Recommend : 5 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not availa- ble ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down.
Page 117 - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 seconds ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not availa- ble )
Page 118 Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. U.S.A CANADA MEXICO ARGENTINA BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA HONDURAS JAMAICA NICARAGUA PANAMA PUERTO RICO REP.
Page 119 022 - 607 - 93 - 33 PORTUGAL (7267864) SLOVAKIA 0800-SAMSUNG (726-7864) http://www.samsung.com/sk SPAIN 902 - 1 - SAMSUNG(902 172 678) SWEDEN 075 - SAMSUNG (726 78 64) http://www.samsung.com/se SWITZERLAND 0848 - SAMSUNG (7267864, CHF 0.08/min) 0845 SAMSUNG (7267864) ESTONIA 800-7267 LATVIA 8000-7267...
Page 120 010-6475 1880 HONG KONG:3698 - 4698 http://www.samsung.com/hk 3030 8282 http://www.samsung.com/in 1-800-3000-8282 1800 110011 0800-112-8888 http://www.samsung.com/id 0120-327-527 http://www.samsung.com/jp 1800-88-9999 http://www.samsung.com/my 0800 SAMSUNG(0800 726 http://www.samsung.com/nz 786) 1-800-10-SAMSUNG http://www.samsung.com/ph (726-7864) 1-800-3-SAMSUNG (726-7864) 02-5805777 1800-SAMSUNG(726-7864) http://www.samsung.com/sg 1800-29-3232, 02-689-3232 http://www.samsung.com/th 0800-329-999 http://www.samsung.com/tw 1 800 588 889 http://www.samsung.com/vn...
Page 121: Correct Disposal
Interlace and Non-Interlace Methods Plug & Play Resolution Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
Page 122 Reproduction in any manner whatsoever without the written permission of Samsung Elec- tronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this ma- terial.

This manual is also suitable for:

Syncmaster 400ux-2 Syncmaster 460ux-2 Syncmaster 460uxn-2 460uxn

Samsung SyncMaster 400UXN-2 User Manual

Quick Links

LCD Display

User Manual

Related Manuals for Samsung SyncMaster 400UXN-2

Summary of Contents for Samsung SyncMaster 400UXN-2

This manual is also suitable for:

Table of Contents