Related Manuals for Samsung SCX-RD100
Summary of Contents for Samsung SCX-RD100
- Page 1 SCX-RD100 COAXIAL REMOTE CONTROLLER user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsungsecurity.com English 1...
- Page 2 Safety i n formati o n CAUTION RISK OF ELECTRIC SHOCK. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
- Page 3 Safety i n formati o n If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.) When cleaning, do not spray water directly onto parts of the product.
-
Page 4: Important Safety Instructions
I m portant Safety I n structi o ns Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Page 5 Part names and functions Checking Installation Environment Installation precautions Connection & Control To Control the camera coaxial communications To control the camera using RS-485 device via coaxial communications To control the camera using RS-232 device via coaxial communications To control the camera using RS-485 signal output To control the camera using RS-485 signal output via RS-232 communications Switch Setting Table...
- Page 6 I n troducti o n INTRODUCTION This product is a remote controller for Samsung’s CCTV cameras of New-generation DSP, via coaxial cable not requiring additional control wirings. ❖ Features • Long-distance remote control Through RS-485 communication, remote control is possible up to 1.2 kilometers.
-
Page 7: Part Names And Functions
- For long distance coaxial communications, you can use this switch for amplifying the control signal. Cable SPEC 5C-HFBT Introduction (X)10 (X)1 2 3 4 5 6 7 8 PROTOCOL REMOTE CONTROLLER SCX-RD100 Compensation 250M or less 200M ~ 500M English 7... - Page 8 Introduction RS-485 TERMINATION & PROTOCOL Setting Switch - You can select to set the RS-485 termination. - Turn this switch ON, if RS-485 termination is required. 2 3 4 5 6 7 8 2 3 4 5 6 7 8 TERMINATION PROTOCOL PROTOCOL...
-
Page 9: Rear Panel
PART NAMES AND FUNCTIONS ❖ Rear Panel - AA BATTERY You can use 4 AA-sized batteries for the power. - The average operation time is 20 hours based on the alkaline battery. (If the battery is discharged, it can cause a distortion of the video signal, or electric interference.) Remove the battery if you do not use the controller for a longer period. - Page 10 Introduction ❖ SCX-RD100 CONTROLLER REMOTE RS-232C USB Port This terminal is used for updating the product’s fi rmware. RS-232 Port (9-pin D SUB) - Used to control remotely using RS-232 communication. RS-485 Port (4-pin) - Used to control remotely using RS-485 communication.
-
Page 11: Checking Installation Environment
CHECKING INSTALLATION ENVIRONMENT • Please check the following instructions before installation for your safety. • The way of connecting the main product with external devices (COAXIAL BNC) is very important to build up a proper system. • Do not disassemble the unit; doing so could expose you to dangerous high voltage points. -
Page 12: Connecti O N & Control
– Four Direction Keys: Used to move the cursor up/down or left/right. – For proper coaxial communication, AI camera should be set to Samsung protocol. Refer to the switch settings. (See page 17) – Control of pan/tilt/zoom using the keys is not supported. - Page 13 Using RS-485 device, you can control the camera menu. – For proper coaxial communication, AI camera should be set to Samsung protocol. Refer to the switch settings. (See page 17) By factory default, protocols of SAMSUNG and PANASONIC are supported.
- Page 14 The RS-232 device is the same as RS-485 regarding the protocol setting, but supports only the Samsung protocol. – For proper coaxial communication, AI camera should be set to Samsung protocol. Refer to the switch settings. (See page 17) RS-232 and RS-485 communications cannot be used for simultaneous input.
- Page 15 Connecti o n & Control TO CONTROL THE CAMERA USING RS-485 SIGNAL OUTPUT SCX-RD100 CONTROLLER REMOTE PROTOCOL TERMINATION COMPENSATION CABLE (X)1 (X)10 (X)100 ADDRESS POWER STATUS POWER Connect the product to DC 12V power source or insert 4 AA-sized batteries into the battery compartment.
- Page 16 Match the camera’s address, baud rate, and protocol to the same to those of the unit. – RS-232 can be controlled using the Samsung protocol alone. Connect the RS-232 device’s cable to the RS-232 port of the main unit. Using RS-232 device, you can control the camera menu.
-
Page 17: Switch Setting Table
Protocol Setting Switch (0 : , 1 : ) Pin 1 Pin 2 Pin 3 Pin 4 By default, it is configured to support SAMSUNG and PANASONIC. NOTE For other protocols, you can find assistance from our website at: http://www.samsungsecurity.com ❖... - Page 18 Connecti o n & Control – See the following table to set the baud rate. 2 3 4 5 6 7 8 TERMINATION PROTOCOL 1. SAMSUNG BAUD RATE 38400 BPS 19200 BPS 9600 BPS 4800 BPS 2. PHILIPS BAUD RATE...
- Page 19 Connecti o n & Control 5. ERNA BAUD RATE 2400 BPS Only supports 2400 bps 6. KALATEL BAUD RATE 9600 BPS 4800 BPS PIN 5 PIN 6 PIN 5 PIN 6 English 19...
-
Page 20: Specifications
WEIGHT 20 – COAXIAL REMOTE CONTROLLER Description COAXIAL INTERFACE Max. 500m (with 5C-HFBT cable) D-SUB 9P 1 Port 4800/9600/19200/38400bps (Only Samsung protocol supported) 4P Terminal Type 1 Port 2400/4800/9600/19200/38400bps (Supports each protocol) S/W PROGRAM UPLOAD Composite Video 1.0Vp-p, 75ohm, Cable Compensation out (Select:S/L) -10˚C ~ +50˚C... - Page 21 Speci fi cati o ns DIMENSIONS Unit (mm) English 21...
- Page 22 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.