Download  Print this page

Parked Recording When The Power Is Off - Kenwood DRV-830 Instruction Manual

Gps integrated dashboard camera
Hide thumbs

Advertisement

Before Using
Manual recording
When the camera's [REC] button is pressed during
interrupted and manual recording starts.
When manual recording ends, continuous recording resumes.
The recording time for manual recording is the 10 seconds before the
z
time after the button was pressed, selectable among 15 seconds (the setting upon purchase), 30 seconds
and 1 minute.
(➜ P. 33)
[REC]
If the
button is pressed again before manual recording ends, manual recording is extended from
z
there for the set amount of time. The maximum recording time per file is 1 minute. When the recording
A p p r o x . 3 m i n u t e s
A p p r o x . 3 m i n u t e s
time reaches 1 minute, the file is split and recording starts on a new file.
Press the [REC] button.
Continuous recording
Continuous recording
Manual recording
10 seconds before button
15 seconds after button
pressed recorded
pressed recorded
Upon purchase, overwriting is set to "OFF". When the upper limit of the number of recordable
z
files is reached, manual recording is no longer possible.
Recorded file storage location
The files are stored in the "MANUAL" folder on the SD card.
z
Still image recording
A p p r o x . 3 m i n u t e s
A p p r o x . 3 m i n u t e s
When the camera's
[
]
button is pressed during
The resolution of the still images is the same resolution as set at "Resolution".
z
Overwrite
Overwrite
Recording is not interrupted when still images are recorded during recording.
z
Still image file storage location
The still image files are stored in the "PICTURE" folder on the SD card.
z
Automatic still image capture
This function automatically captures a set number of still images at fixed intervals.
[
]
When the
button is pressed and held for over 1 second, the automatic still image capture
function turns on.
[
]
When the
button is pressed and held for over 1 second or the set number of images are captured,
z
the automatic still image capture function turns off.
The number of images can be selected from among 10, 30 (the setting upon purchase) and 50. The capture interval
z
can be selected from among 1 minute, 5 minutes (the setting upon purchase), 15 minutes and 30 minutes.
The resolution of the automatically captured still images is the same resolution as set at "Resolution".
z
If the camera's power is turned off while the automatic still image capture function is on, the automatic still
z
image capture function turns off. Capturing does not resume even if the camera's power is turned back on.
The capture function also turns off if the menu or shortcut menu screen is displayed or if the recording
z
mode is changed during recording.
22
recording,
continuous
continuous
[REC]
button was pressed and a set
・・・・・
A p p r o x . 3 m i n u t e s
(➜ P. 45)
・・・・・
A p p r o x . 3 m i n u t e s
recording, a still image is recorded.
continuous
(➜ P. 33)
(➜ P. 45)
Automatically captured still image file storage location
The still image files are stored in the "PICTURE" folder on the SD card.
recording is
z

Parked recording when the power is off

To enable the parked recording function, the power must be connected with the CA-DR100
power cable for Dashcam (optional accessory).
Parked recording does not work if the power is turned off with the camera's power button
z
before turning the vehicle's engine key off.
Parked recording may not work if the power supply voltage is low due to deterioration of the
z
vehicle's battery, etc.
Parked recording
When the vehicle's engine key is turned off, the parked recording function is set to standby and the
camera monitors the vehicle for impacts. When an impact to the vehicle is detected, the power turns
on and parked recording starts. When parked recording ends, the power turns off and the function
is set back to standby.
The recording time for parked recording can be selected among OFF (parked recording not performed),
z
10 seconds (the setting upon purchase), 20 seconds and 30 seconds. When OFF (parked recording not
performed) is set, the parked recording function is turned off.
With parked recording, recording starts several seconds after the impact is detected.
z
The sensitivity for detecting impacts can be set.
z
Standby
No picture is displayed on the monitor screen during parked recording.
z
If parked recording has been performed, the user is notified when the power is turned on by
z
audio guidance and a monitor display.
The overwrite setting is set to "ON" upon purchase. When the upper limit of the number of
z
recordable files is reached, recording continues, overwriting the oldest files.
Disabling parked recording when getting in and out of the vehicle
Parked recording may be activated when the vibrations from the door closing are detected when
getting in and out of the vehicle. Parked recording can be disabled temporarily so that it is not per-
formed when the vibrations from the door closing are detected when getting in and out of the vehicle.
The start time (when getting out) and stop time (when getting in) can be selected among OFF (the setting
(➜ P. 33)
z
upon purchase), 30 seconds, 1 minute and 3 minutes.
(➜ P. 33)
Parked recording file storage location
The parked recording files are stored in the "PARKING" folder on the SD card.
z
A p p r o x . 3 m i n u t e s
A p p r o x . 3 m i n u t e s
A p p r o x . 3 m i n u t e s
Continuous recording
Continuous recording
A p p r o x . 3 m i n u t e s
A p p r o x . 3 m i n u t e s
A p p r o x . 3 m i n u t e s
Overwrite
Overwrite
(➜ P. 32)
(➜ P. 32)
Impact detection
Parked recording for 10 seconds
(➜ P. 32)
・・・・・
(➜ P. 45)
・・・・・
(➜ P. 45)
23

Advertisement

Table of Contents
loading

  Related Manuals for Kenwood DRV-830