yellow jacket P51-870 Titan Quick Start Manual

P51-870 TITAN
Digital Manifold
Quick Start Guide
For addi�onal informa�on regarding the P51-870 TITAN™
and ManTooth™ App opera�on, please see the User Manual
and ManTooth Quick Start Guide at www.yellowjacket.com.
3
Modes Menu
wer
Units Menu
ressure as measured by a YJ auxiliary
Plug the low side temperature probe into T1 on the back
vacuum sensor. Plug the vacuum sensor into either A1 or A2 on the back of
of the device. Plug the high side temperature probe into
the device. Tap Target to set th
T2 on the back of the device.
6
ck
vacuum sensor. Plug the vacuum sensor into either A1 or A2 on the back of epleted, the user is prompted
While in Pressure/Temperature mode, tapping the center of either gauge
o
to start a pressure hold test. the device. Tap Target to set th
will convert the gauge into a graph. Tap the center of the graph to convert
the graph back to a gauge.
pressure hold setup screen.
1
Tap to power
unit on
®
Units Menu
4
Session Timer
Menu
Refrigerant
Menu
Allowable change is the maximum allowable vacuum pressure the
system is allowed to reach before failure. Set the allowable change value
vacuum sensor. Plug the vacuum sensor into either A1 or A2 on the back of
While in Pressure/Temperature mode, tapping the center of either gauge the device. Tap Target to set th
p Hold to will convert the gauge into a graph. Tap the center of the graph to convert
the graph back to a gauge.
7
Plug the low side temperature probe into T1 on the back
of the device. Plug the high side temperature probe into
T2 on the back of the device.
Allowable change is the maximum allowable vacuum pressure the
ressure as measured by a YJ auxiliary
system is allowed to reach before failure. Set the allowable change value
e p Hold to
Refrigerant
Tap to power
Menu
unit on
ressure as measured by a YJ auxiliary
hold test
When ready to begin the pressure
The Pressure Rise test
will monitor the
current vacuum
pressure and the
percent change in
pressure. The device
will prompt the user
with a Pass or Fail
message depending if
epleted, the user is prompted
the system passes or
to start a pressure hold test.
fails the test When ready to begin the pressure
pressure hold setup screen.
2
The Pressure Hold mode displays the change in pressure
during a standing pressure test. Allowable change is the p
the current system pressure the system is allowed to dro
pressure test is deemed a failure. Set the allowable chang
Units Menu
Plug the low side temperature probe into T1 on the back
to Pressure Decay to begin the pressure hold te
of the device. Plug the high side temperature probe into
T2 on the back of the device.
5
Allowable change is the maximum allowable vacuum pressure the
system is allowed to reach before failure. Set the allowable change value
p Hold to
vacuum sensor. Plug the vacuum sensor into either A1 or A2 on the back of
rn to the units menu. Exit will return without saving
the device. Tap Target to set th
ile in the units menu to return
8
While in Pressure/Temperature mode, tapping the center of either
will convert the gauge into a graph. Tap the center of the graph to c
the graph back to a gauge.
hold test
e
to start a pressure hold test.
pressure hold setup screen.
Modes Menu Session Timer
Menu
Refrigerant
Menu
W
wi
th
Tap Set Pi
begin moni
drop in syste
The device w
Fail or Pass
to the Units menu. Use
depending i
to be altered. Once
Fails or P
hold test
ressure as measured by a YJ auxiliary sys
n. Press the select
pressur
When ready to begin the pressure
p Hold to
The Pressure Rise test
will monitor the
current vacuum
pressure and the
percent change in
pressure. The device
will prompt the user
with a Pass or Fail
message depending if
the system passes or
user to the
epleted, the user is prompted
fails the test
e
p and down To charge the
m the new
of the device.