Download  Print this page

Mitsubishi Electric PAR-F27MEA Instruction Book

City multi control system me remote controller.
Hide thumbs
Most useful pages: More
   

Advertisement

WT03299X01
GB
CITY MULTI Control System
ME Remote Controller
PAR-F27MEA
Instruction Book
Thank you for purchasing a Mitsubishi CITY MULTI system.
To use your CITY MULTI system correctly and safely, please read this book before use.
After reading this book, keep it and the installation manual in a place where the final user can see them at anytime.
When the end user has changed, forward this book and the instruction manual to the new final user.
Do not try to install or move this system by yourself. (Safety and functions cannot be ensured)
1
Safety Precautions
The following two symbols are used to dangers that may be caused by incorrect use and their degree:
WARNING
This symbol denotes what could lead to serious injury or death if you misuse the PAR-F27MEA.
CAUTION
This symbol denotes what could lead to a personal injury or damage to your property if you misuse the PAR-F27MEA.
WARNING
Ask your dealer or technical representative to install the unit.
Do not move and re-install the PAR-F27MEA yourself.
Any deficiency caused by your own installation may result in an electric shock
Any deficiency caused by installation may result in an electric shock or fire.
or fire.
Ask your distributor or special vendor for moving and installation.
Securely install in a place which can withstand the weight of the con-
To dispose of this product, consult your dealer.
troller.
Never modify or repair the PAR-F27MEA by yourself.
If it is not enough, the controller may drop and cause an injury.
Any deficiency caused by your modification or repair may result in an electric
Make sure that the controller is connected to a rated power supply.
shock or fire.
If the controller is not connected to a rated power supply, it may cause a fire
Consult with your dealer about repairs.
or damage to the controller.
Stop the operation immediately and notify the your dealer if an error
Stop the operation if any malfunction occurs.
code is displayed or malfunction occurs.
If malfunction occurs (burning smell, etc.) stop the operation and turn off the
Fire or damage may cause it the controller is operated in this condition.
power supply. Contact the your dealer or technical representative immediate.
If the controller continues to operate after a malfunction occurs, this may
cause damage, electric shock or fire.
CAUTION
Do not install in any place exposed to flammable gas leakage.
Do not use in any special environment.
Flammable gases accumulated around the body of PAR-F27MEA may cause
Using in any place exposed to oil (including machine oil), steam and sulfuric
an explosion.
gas may deteriorate the performance significantly or give damage to the com-
ponent parts.
Do not wash with water.
Doing so may cause an electric shock or a malfunction.
Do not press any control button using a sharp object.
Doing so may cause an electric shock or a malfunction.
Do not touch any control button with your wet hands.
Doing so may cause an electric shock or a malfunction.
Operate the controller within the specified temperature range.
Observe the specified temperature range when operating the controller. If
Do not use the controller for special applications.
the controller is used outside the specified temperature range, it may cause
This product is designed for use with the CITY MULTI CONTROL SYSTEM.
serious damage. Be sure to check the operation temperature range in the
Do not use the system for other air condition management operation or appli-
operation manual.
cations. It may cause malfunctions.
Do not pull or twist the transmission line.
Do not apply insecticide or flammable sprays to the controller.
It may cause a fire or malfunction.
Do not place flammable spray near the controller and make sure it does not
blow directly on the controller as this may cause in fire.
Do not dismantle the unit.
It is dangerous to touch the internal circuit board. It may cause a fire or mal-
Do not clean the unit using benzene, thinner or other chemicals.
function.
It may cause discoloration or other damage. If the unit should become par-
ticularly dirty, apply a mild cleaner that has been diluted with water to a soft
cloth and wipe the unit clean. Be sure to wipe away any residual moisture
with a dry cloth.
3
How to Operate
(1) On/off and operation mode selection and room temperature adjustment
3
4
˚C
2
˚C
1
TEMP.
ON/OFF
1
3
FILTER
CLOCK→ON→OFF
CHECK TEST
PAR-F27MEA
TIMER SET
2
When starting operation
When you want to change the set temperature
Press the [ON/OFF] button 1.
<When you want to lower the room temperature>
• The ON lamp 1 and display light.
Press the [TEMP. (
)] button 3.
<When you want to raise the room temperature>
NOTE
The restarting operation contents are shown below.
Press the [TEMP. (
)] button 3.
• The set temperature changes 1 °C each time the button is pressed.
The set temperature is displayed at 3.
Remote controller settings
• The following specified temperatures can be set:
Operation
Cool/dry
Last operation mode
Heat operation
Auto operation
mode
operation
Temperature
Last set temperature
19(14) to 30 °C
17 to 28 °C
19 to 28 °C
setting
Wind speed
Last set wind speed
NOTE
Horizontal
When "LIMIT TEMP." is displayed on the screen, the specified tempera-
outlet
ture range is limited. Therefore, the temperature range that can be
Operation
Airflow
Last setting
changed becomes narrow.
mode
Horizontal
Room temperature display
outlet
During operation, the intake temperature is displayed at 4.
When stopping operation
NOTES
Press the [ON/OFF] button 1.
• The ON lamp 1 and display go off.
- The display range is 8 to 39 °C. When this range is exceeded, the
room temperature display flashes at 8 °C or 39 °C.
- When multiple indoor units are controlled, the contents of the master
When selecting the operation mode
indoor unit are displayed on the remote controller.
Press the [Mode selection] button 2 while the air conditioner is oper-
- The room temperature sensor position can be selected from "INDOOR
ating.
UNIT" and "REMOTE CONTROLLER".
• The setting is switched each time the button is pressed.
The initial setting is "INDOOR UNIT". When you want to change the
The operation mode is displayed at 2.
room temperature sensor position to "REMOTE CONTROLLER", con-
sult your dealer.
- When "no room temperature display" was selected by remote control-
ler function selection, the room temperature is not displayed.
NOTE
The auto and heating functions may not be installed, depending on the
outdoor unit model.
2
Part Names
"CENTRALLY CON-
"TIMER" "DAILY"
"Current/Starting/
TROLLED" display
"AUTO OFF" Display
Ending/REMAINING
time" display
Displayed when air conditioner
Displays the timer mode when
operation is prohibitted by a cen-
the timer is set.
Displays the current time and
tral controller, etc. When the re-
There are three timers modes:
timer set times.
mote controller buttons are
1 day timer, daily timer, and auto
When the timer is operating, dis-
locked, this display flashes.
off timer. One of these modes
plays the normal time and the
can be selected.
stating, ending, or remaining
time.
"Set temperature"
display
Displays the set temperature.
CENTRALLY CONTROLLED
1Hr.
DAILY
ON OFF
˚C
AUTO OFF
CLOCK
(For description purposes, all the
REMAINDER
FILTER
displays are assumed to be on.)
STAND BY
˚C
LIMIT TEMP.
DEFROST
NOT AVAILABLE
"Operation mode"
"Airflow" display
"Room temperature"
display
Displays the operation mode.
Displays the outlet air direc-
tion.
Displays the intake temperature
while the air conditioner is op-
"Wind speed"
erating.
display
"Set effective for 1 hr."
Displays the selected wind
display
speed.
Displayed when low downward
"Louver" display
is selected at cooling and elec-
tronics dry operation.
Displays operation of the
(Differs with the model.)
swing louver. It is not dis-
After one hour, the display goes
played when the louver is
off, and swing also switches.
stopped.
DISPLAY SECTION
1Hr.
CENTRALLY CONTROLLED
TEMP. buttons
DAILY
ON OFF
˚C
AUTO OFF
CLOCK
REMAINDER
FILTER
CHECK MODE
( ) Lower ( ) Raise
TEST RUN
˚C
STAND BY
NOT AVAILABLE
LIMIT TEMP.
DEFROST
TEMP.
ON/OFF
Timer selection button
FILTER
CLOCK→ON→OFF
Mode selection button
CHECK TEST
PAR-F27MEA
TIMER SET
Time selection buttons
( ) Return ( ) Ahead
Open the door.
OPERATION SECTION
NOTE
When an operation button is pressed, if the indoor unit does not have that function, "NOT AVAILABLE" flashes.
1
When one remote controller controls multiple indoor units, if the master indoor unit has the selected function, this message is not displayed.
(2) Wind speed and wind direction adjustment and fan operation
˚C
˚C
TEMP.
ON/OFF
FILTER
CLOCK→ON→OFF
CHECK TEST
PAR-F27MEA
TIMER SET
When you want to change the wind speed
When you want to change the wind direction
While the air conditioner is operating, press the [Wind speed] button
While the air conditioner is operating, press the [Airflow] button 6.
• Each time the button is pressed, the setting changes as shown be-
5.
• Each time the button is pressed, the setting changes as shown be-
low.
low.
The wind direction is displayed at 6.
The wind speed is displayed at 5.
• The following wind directions can be selected:
• The following wind speeds can be selected:
Wind speed
Remote controller display
Display
(Low) (Mid1)
(Mid2)
(High)
Fan
4-speed model
Operation
Wind
Cannot be set.
mode
Speed
(Mid1)
(Mid2)
(High)
High/Mid1
3-speed model
Heat/fan
Mid2/Low
High
(Mid1)
(High)
Cool
Mid1/Mid2/Low
2-speed model
Not
Dry
settable
* The wind speeds that can be selected depend on the model.
Airflow
setting
when operation
mode was changed
NOTES
- In cases such as the following, the liquid crystal display and unit wind
* After one hour, automatically returns to the horizontal position.
speed are different:
* During swing operation, remote controller display and airflow vane po-
1. When "HEAT STAND BY" or "DEFROSTING" is displayed.
sition cannot be synchronized.
2. Immediately after heating operation (while waiting for mode selec-
* There may not be an airflow function, depending on the model.
tion)
3. When the room temperature is higher than the set temperature in the
NOTE
heating mode.
4. Dry operation
- In cases such as the following, the liquid crystal display and unit airflow
- For 3-speed models, a central controller wind speed display and the
may be different.
remote controller wind speed display may be different.
1. When "HEAT STANDBY"or "DEFROSTING" is displayed
2. Immediately after heating operation (Waiting for mode selection)
3. When the room temperature is higher than the set temperature in
the HEAT mode
Fan operation
<When operating fan interlocked with indoor unit>
<When you want to change the fan wind speed>
When the indoor unit is operated, the fan is automatically operated also.
Press the [Ventilation] button 7.
Each time the button is pressed, the wind speed is changed as shown
Fan operation is displayed at 7.
below.
Remote controller display
<When operating fan only while indoor unit stopped>
While the air conditioner is stopped, press the [Ventilation] button 7.
The ON/OFF lamp 1 lights and fan operation is displayed at 7.
3
- Depending on the indoor unit and fan model, the indoor unit may operate even when only the fan was operated.
NOTES
- When "NOT AVAILABLE" is displayed when the [Ventilation] button 7 was pressed, the fan is not interlocked.
(3) How to operate the timer
There are the following three timer modes. Select one of them.
1) 1 day timer mode
In this mode, the ON and OFF timers (10-minute units) can each be set to one time within 24 hours.
This mode has the following three setting methods:
· ON timer operation
: Timer only starts the air conditioner.
· OFF timer operation
: Timer only stops the air conditioner.
"Senser" display
· ON/OFF timer operation: Timer both starts and stops the air conditioner.
Displayed when the remote
2) Daily timer mode
controller sensor is used.
Operation of this mode is the same as that of the 1 day timer mode. However, timer operation can be set to the same time each day in accordance
with the set ON/OFF timer time. (ON/OFF timer each 1 time/daily)
"FILTER" display
3) Auto off timer mode
Indicates that it is time to
The OFF timer can be easily set in 30-minute units. (30 minutes to 4 hours range) When the remaining time reaches 0:00, the air conditioner stops.
When the Auto off timer mode is selected, the next time the air conditioner is started, the OFF timer operates automatically so that the timer can be
clean the filter.
used to turn off the air conditioner if you should forget.
"LIMIT TEMP." display
NOTE
Displayed when the set tem-
When ON/OFF operation from the central controller, etc. was restricted when timer operation was set, the set ON/OFF timer is not executed. After the
perature range is controlled by
restriction is removed, timer operation is performed at the ON/OFF time.
remote controller functions se-
When ON/OFF operation was restricted during AUTO OFF timer operation, the remaining time at the point operation was restricted is memorized and the
lection.
air conditioner is stopped after the memorized remaining time from the time the restriction was removed.
"Ventilation" display
Displayed during fan operation.
" " display
OFF
˚C
Displayed while the power is on.
˚C
"NOT AVAILABLE"
TEMP.
ON/OFF
display
CLOCK→ON→OFF
FILTER
When the button of a function
3
that is not installed at the indoor
CHECK TEST
unit was pressed, this display
TIMER SET
PAR-F27MEA
flashes simultaneously with the
corresponding function display.
When setting the current time
Press the [Time selection] button 1 and display "CLOCK".
• Each time the button is pressed, the time is switched as shown below.
ON
OFF
ON/OFF lamp
CLOCK
REMAINDER
ON/OFF button
Each time the [Time selection (
)] button 2 is pressed, the time advances one minute and each time the [Time selection (
Wind speed button
time returns one minute.
• When the button is held down, the time advances or returns continuously. The time changes in 1 minute units → 10 minutes units → 1 hour units order.
• About 10 seconds after the end of setting, the remote controller display goes off.
FILTER button
* When a power failure occurs, the current time is reset. Reset the clock.
When performing ON timer operation (1 day timer mode/daily timer mode)
CHECK button
Press the [Time selection] button 1 and check "Current time (CLOCK)" and display "Starting time (
(Normally not used)
Set the ON time by pressing the [Time selection (
) or (
Set the OFF time to "-- : --" display.
• "-- : --" display is displayed between 23 : 50 and 0 : 00.
TEST RUN button
Press the [Timer selection] button 3 and set the display to " " (1 day timer mode) or " " + "DAILY" (daily timer mode).
(Normally not used)
• Each time the button is pressed, the timer mode is switched as shown below.
Airflow button
DAILY
Off
Louver button
(1 day timer mode)
(Daily timer mode)
Ventilation button
* The Auto off timer mode is skipped at the OFF window.
When performing OFF timer operation (1 day timer mode/daily timer mode)
Built-in temperature sensor position
Press the [Time selection] button 1 and check "Current time (CLOCK)" and set the display to "Ending time (
Set the OFF time by pressing the [Time selection (
) or (
Set the ON time to "-- : --" display.
Press the [Timer selection] button 3 and set the display to " " (1 day timer mode) or " " + "DAILY" (daily timer mode).
2
(5) Other displays and flashing
– "CENTRALLY CONTROLLED" display –
CENTRALLY CONTROLLED
˚C
˚C
5
• Displayed when operation is controlled by central controller, etc.
Restricted operations are shown below.
6
· ON/OFF (including timer operation)
· Operation mode
· Set temperature
NOTE
7
May also be individually restricted.
1
1
5
– "FILTER" flashing –
6
˚C
7
FILTER
˚C
• Indicates that the filter needs cleaning.
Clean the filter.
• When resetting "FILTER" display
When the [FILTER] button is pressed two times successively after
cleaning the filter, the display goes off and is reset.
– "ERROR CODE" flashing –
Setting 1
Setting 2
Setting 3
Setting 4
Swing
CHECK
(horizontal 0˚)
(horizontal 45˚)
(horizontal 60˚)
(horizontal 85˚)
ERROR CORD
ON/OFF
unit number
• When both the "ON" lamp and "ERROR CODE" flash, trouble oc-
curred in the air conditioner and the air conditioner stops.
Horizontal
Downward
Downward
Downward
Jot down the unit number and error code and turn off the air condi-
Swing
outlet
45˚
60˚
85˚
tioner power and consult your dealer.
Horizontal outlet
Downward 45˚
Downward 60˚
Downward 85˚
(6) How to select the remote controller functions
Swing
In the remote controller function selection mode, three functions can be selected and changed. Select and change them as required.
* Horizontal after 1 hour
1) Operation mode display selection mode (Automatic mode cool/heat display selection)
Cool
When the AUTO operation mode was set by remote controller, the indoor unit is judged from the room temperature and the cooling or heating
Dry
Heating
operation is performed automatically. In this case, "AUTO" "COOL" or "AUTO" "HEAT" is displayed at the remote controller. However, "AUTO" can be
Fan
operation
displayed alone without the "COOL" or "HEAT" display.
operation
2) Room temperature display selection mode (Room temperature display/no display selection)
Normally, the intake temperature is displayed at the remote controller, but setting can be performed so that it is not displayed.
3) Set temperature range limit mode
Ordinarily, the set temperature adjustment range can be freely set to the 19 °C to 30 °C range for cooling and dry and the 17 °C to 28 °C range for
heating. However, the lower limit temperature can be preset to an arbitrary value for cooling and dry and the upper limit temperature can be preset
to an arbitrary value for heating. If the set temperature range for cooling and dry is set to a value higher than normal and the set temperature range
for heating is set lower than normal in this way, overcooling and overheating can be prevented and energy can be saved.
NOTE
When the set temperature adjustment range was changed from the normal set temperature adjustment range by remote controller connected to a cooling/
heating simultaneous air conditioner with an AUTO mode, the AUTO mode cannot be selected with the [Mode selection] button.
[Remote controller function selection mode transition]
OFF window
1 ↑
Remote controller function selection modes
Operation mode display selection mode
2
TEMP.
ON/OFF
Off
3
CLOCK→ON→OFF
FILTER
Room temperature display selection mode
(no display)
CHECK TEST
PAR-F27MEA
TIMER SET
Set temperature adjustment range limit mode (cool/dry)
4
4
1
Set temperature adjustment range limit mode (heat)
When performing ON/OFF timer operation (1 day timer mode/daily timer mode)
See the setting when performing ON timer and OFF timer operation and check "Current time (CLOCK)" and set both the ON time and OFF time.
Press the [Timer selection] button 3 and set the display to " " (1 day timer mode) or " " + "DAILY" (daily timer mode).
When performing AUTO OFF timer operation (AUTO OFF timer mode)
The Auto off timer can only be set while the air conditioner is operating.
Press the [Timer selection] button 3 and set the display to" " + "AUTO OFF" (Auto off timer mode).
Set the desired remaining time by pressing the [Time selection (
After remaining time setting, the timer automatically starts.
When releasing timer operation
Press the [Timer selection] button 3 and turn off the "TIMER" display.
Off
* The Auto off timer mode is skipped at the OFF window.
(4) Auto lock
Remote controller buttons operation can be locked. There are two kinds of auto lock.
1) All buttons lock: Locks all the remote controller buttons.
2) Lock other than [ON/OFF] button: Locks all the remote controller buttons except the [ON/OFF] button.
[Timer setting display example]
• 1 day timer mode
NOTE
ON
← 1 day timer mode
8 A.M. operation start
When auto lock is set, "– CENTRALLY CONTROLLED –" flashes.
• Daily timer mode
DAILY
OFF
← Daily timer mode
5 P.M. daily operation stop
1
• Auto off timer mode
2
← Auto off timer mode
AUTO OFF
Operation stop when 2 hours remain
REMAINDER
When locking/unlocking all buttons
No display
When the [TEMP. (
)] button 1 is pressed two seconds successively while pressing the [FILTER] button, all the remote controller buttons are locked
or unlocked.
All buttons lock
)] button 2 is pressed, the
• While locked, all the remote controller buttons cannot be operated. When all the buttons are locked in the timer mode, timer operation is performed
even though the buttons are locked.
ON
)".
)] button 2.
When locking/unlocking all the buttons other than the [ON/OFF] button
When the [ON/OFF] button 2 is pressed and held down for two seconds while pressing the [FILTER] button, all buttons other than [ON/OFF] button
are locked or unlocked.
Lock other than
[ON/OFF] button
AUTO OFF
Press and hold down at the same time for 2 seconds
(Auto off timer mode)
• While locked, buttons other than the [ON/OFF] button cannot be operated. When locked in the timer mode, the timer operation is performed even
though the buttons are locked.
OFF
)".
)] button 2.
5
[PROCEDURE]
1. Set the air conditioner to the off state with the remote controller [ON/OFF] button. The remote controller display shifts to the OFF window display
– "Operation mode" flashing –
shown at the left.
2. When the [CHECK] and [Mode selection] buttons 1 are pressed and held down at the same time for two seconds, the remote controller switches to
the remote controller function selection mode and the "OPERATION MODE DISPLAY SELECTION MODE" window appears. The other three modes
˚C
can be selected by operating the [TEMP.] (
˚C
OPERATION MODE DISPLAY SELECTION MODE (When you want to change the AUTO mode display)
<When flashes continuously>
• "AUTO" "COOL/HEAT" flashes and "ON" or "OFF" lights. Each time the [Time selection (
• Displayed when another indoor unit connected to the outdoor unit is
"OFF" display is switched.
already operating in a different operation mode.
Match with the operation mode of the other indoor unit.
<When mode switched after display flashes>
• Displayed when operation mode is restricted for each season by cen-
tral controller, etc.
• When "ON" was selected, "AUTO" "COOL" or "AUTO" "HEAT" is displayed during AUTO mode operation.
Use another operation mode.
• When "OFF" was selected, only "AUTO" is displayed during AUTO mode operation.
ROOM TEMPERATURE DISPLAY SELECTION MODE (When you want to change room temperature display/no display)
• "88 °C" flashes at the room temperature display and "ON" or "OFF" lights. Each time the [Time selection (
NOTES
state, the "ON" and "OFF" display is switched.
- When two or more different types of indoor unit are controlled, the clean-
ing period differs with the type of filter. When the master unit cleaning
period arrives, "FILTER" is displayed. When the filter display goes off,
the cumulative time is reset.
- "FILTER" indicates the cleaning period when the air conditioner was
used under general indoor air conditions by criteria time. Since the de-
gree of dirtiness depends on the environmental conditions, clean the
• When "ON" was selected, the room temperature is continuously displayed in the ON window.
• When "OFF" was selected, the room temperature is not displayed in the ON window.
filter accordingly.
- The filter cleaning period cumulative time differs with the model.
SET TEMPERATURE RANGE LIMIT MODE (When you want to change the set temperature adjustment range)
1) Cool/dry mode temperature selection
"COOL/DRY" and "LIMIT TEMP." light on the display and the set temperature adjustment range in the cool (dry) mode is displayed.
The lower limit temperature of the set temperature display flashes. This temperature value can be set and changed.
[Lower limit temperature adjustment range]: 19 °C
fixed. Only the lower limit temperature can be changed.)
ON lamp (flashed)
˚C
˚C
ERROR CORD
ON/OFF
˚C
• When only "ERROR CODE" flashes
[When set temperature adjustment range in cool/dry mode is 19 °C to 30 °C]
(ON lamp remains a steady light)
The air conditioner continues to operate, but there is the possibility of
2) Each time the [Time selection (
trouble occurring.
set temperature adjustment range.
Jot down the error code and consult your dealer.
˚C
[When set temperature adjustment range was set to 24 °C to 30 °C]
3) When the [TEMP. (
"HEAT" and "LIMIT TEMP." light on the display and the heat mode set temperature adjustment range is displayed.
The upper limit temperature value can be changed by pressing the [Time selection (
selection.
Upper limit temperature adjustment range: 17 °C to 28 °C (17 °C
17 °C is fixed. Only the upper limit temperature can be changed.)
3. At the end of selection of each function, release the remote controller function selection mode and display the OFF window by pressing the [CHECK]
and [Mode selection] buttons 1 at the same time for two seconds.
4
Specifications
Item
Size
Weight
Power requirement
↓ 1
[Remote controller OFF window display]
Power consumption
1:Press and hold down the [CHECK] and
Environmental conditions
3 ↑
↓ 2
[Mode selection] buttons at the same
2
3
time for 2 seconds
Material
3 ↑
↓ 2
2:[TEMP. (
)] button
3:[TEMP. (
)] button
3 ↑
↓ 2
7
) or (
)] button 2. (30 minutes units, 30 minutes to 4 hours)
DAILY
AUTO OFF
(1 day timer mode)
(Daily timer mode)
(Auto off timer mode)
CENTRALLY CONTROLLED
˚C
˚C
TEMP.
ON/OFF
1
2
CLOCK→ON→OFF
FILTER
CHECK TEST
PAR-F27MEA
TIMER SET
Unlock
[FILTER] + [TEMP. (
)]
Press and hold down at the same time for 2 seconds
Unlock
[FILTER] + [ON/OFF]
6
) button 2 or (
) button 3. Display the mode whose function you want to change.
) or (
)] button 4 is pressed in this state, the "ON" and
[Time selection (
) ((
))] button
) or (
)] button 4 is pressed in this
˚C
˚C
[Time selection (
) ((
))] button
30 °C (Mid temperature indoor unit: 14 °C
30 °C) (Upper limit temperature 30 °C is
LIMIT TEMP.
) or (
)] button 4 is pressed, the lower limit temperature value is increased or decreased. Set it to the desired
LIMIT TEMP.
)] button 2 is pressed after the setting above, the remote controller switches to the heat mode temperature selection window.
) or (
)] button 4, the same as cool/dry mode temperature
28 °C for mid temperature indoor unit also) (The lower limit temperature
Contents
120 (H) × 130 (W) × 19 (D) mm
0.2 kg
DC30 V Power supplied from M-NET transmission line (Normally, power is received from the outdoor unit over
the indoor/outdoor unit M-NET transmission line.)
0.5 W
Temperature 0 to 40 °C, humidity 30 to 90 % RH (No condensation)
PS
8

Advertisement

Table of Contents

   Related Manuals for Mitsubishi Electric PAR-F27MEA

Comments to this Manuals

Symbols: 0
Latest comments: