Meter - Kenwood TS-890S Instruction Manual

3 MENU
Advanced Menu Items
Menu Display
Indication Signal Type (External
0

Meter 1)

Indication Signal Type (External
1
Meter 2)
2 Output Level (External Meter 1) Level of external meter output 1
3 Output Level (External Meter 2) Level of external meter output 2
4 Reference Signal Source
Reference Oscillator
5
Calibration
TX Power Down with
6
Transverter Enabled
7 TX Hold After Antenna Tuning
8 Antenna Tuner during RX
Antenna Tuner Operation per
9
Band
10 Microphone Gain (FM Mode)
11 PKS Polarity Reverse
12 TX Inhibit While Busy
CTCSS Unmute for Internal
13
Speaker
14 PSQ Logic State
15 PSQ Reverse Condition
PSQ/ PKS Pin Assignment
16
(COM Connector)
Virtual Standard COM Port -
17
RTS
Virtual Standard COM Port -
18
DTR
Virtual Enhanced COM Port -
19
RTS
Virtual Enhanced COM Port -
20
DTR
21 External Display
22 Resolution (External Display)
23 Touchscreen Calibration
24 Software License Agreement
Important Notices concerning
25
Free Open Source
About Various Software
26
License Agreements
27 Firmware Version
Reset Menu Items
Display
Menu Reset
Memory Channel Reset
VFO Reset
Standard Reset (The Clock, TX Inhibit, and
Transmit Power Upper Limit will not be reset)
Full Reset
3-8
Description
Target of external meter output 1
Target of external meter output 2
Switches the reference signal
Adjusts the frequency of the reference
oscillator
Powers down the transverter function
Holds transmission at the end of antenna
tuning
Antenna tuner behavior while receiving
Antenna tuner behavior for each band
FM microphone gain
Reversing of PSK polarity
Inhibits transmission while in the BUSY
state
Mute behavior of CTCSS
SQL control signal logic
SQL output conditions
PSQ/PKS mode setting
RTS settings of virtual COM port
(Standard)
DTR settings of virtual COM port
(Standard)
RTS settings of virtual COM port
(Standard)
RTS settings of virtual COM port
(Standard)
External display output
Resolution settings of external display
Touchscreen adjustment
Software license of this transceiver
Ways to obtain open source resources
used by this transceiver
Licenses related to software used by this
transceiver
Firmware version used by this
transceiver
Menu reset
Memory channel reset
VFO reset
Standard reset
Full reset
Setting Value
Automatic/ TX Power/ ALC/ Drain
Voltage (Vd)/ Compression Level
(COMP)/ Current (Id)/ SWR
Automatic/ TX Power/ ALC/ Drain
Voltage (Vd)/ Compression Level
(COMP)/ Current (Id)/ SWR
0 to 100 [%] (1 step)
0 to 100 [%] (1 step)
Internal/ External
-500 to +500 (1 step)
Off/ On
Off/ On
Off/ On
Off/ On
0 to 100 (1 step)
Off/ On
Off/ On
Mute/ Unmute
Low/ Open
Off/ Busy/ Sql/ Send/ Busy-Send/
Sql-Send
Off/ On
Flow Control/ CW Keying/ RTTY
Keying/ PTT/ DATA SEND
Off/ CW Keying/ RTTY Keying/
PTT/ DATA SEND
Off/ CW Keying/ RTTY Keying/
PTT/ DATA SEND
Off/ CW Keying/ RTTY Keying/
PTT/ DATA SEND
Off/ On
800 x 600/ 848 x 480
–
–
–
–
–
Description
Default Refer to
TX Power 16-6
Automatic 16-6
50 [%] 16-6
50 [%] 16-6
Internal 16-8
0 17-2
On 16-15
Off 4-11
Off 4-12
Off 4-12
50 5-28
Off 16-12
Off 16-12
Mute 16-8
Low 16-8
Sql 16-8
Off 16-8
Flow Control 16-12
Off 16-12
Off 16-12
Off 16-12
On 16-7
800 x 600 16-7
– 17-3
– i
– ii
– ii
– 17-1
Refer to
17-1