Subscribe to Our Youtube Channel
Related Manuals for Russound SP622.1
Summary of Contents for Russound SP622.1
- Page 1 A / V D I S T R I B U T I O N & C O N T R O L S Y S T E M S Instruction Manual SP652.1 SP622.1...
-
Page 2: Speaker Wire
RUSSOUND speakers, they combine acoustic technology with dura- bility and will provide years of musical enjoyment. This manual is designed to make your SP652.1 & SP622.1 speakers as easy to install as they are to listen to. If you’ve had any home “do-it- yourself”... -
Page 3: Stereo Imaging
STEREO IMAGING If your Russound In-wall Speakers are going to be your primary lis- tening source in a room, you need to consider some other factors to insure proper imaging. The term “stereo imaging” refers to a speaker system’s ability to project music so that it sounds like the performers... -
Page 4: Other Acoustic Considerations
2x4 stud wall. In fact, the dense, rigid nature of plasterboard or (lath and plaster in older homes) acts as a superb speaker baffle. You can also install Russound speakers in stud walls covered with thick wood paneling or in wallboard/plaster ceilings. However, avoid: •... -
Page 5: Speaker Wire Paths
Russound In-Wall Speakers, skip to the section “cutting holes”. But if you want your speakers to completely blend in with a colored wall or accent the surface, now is the time to paint your Russound speakers’ outer frames and perforated grilles. -
Page 6: Cutting Holes For The Speakers
* If you want a custom look, install an outlet box against a stud and cover it with a single outlet plate which has one hole in the mid- dle for the wires to exit from OR order from your Russound dealer a Russound Stereo pair Wall Plate Connector. -
Page 7: Hooking Up Your Speakers
* Make sure that no stray strands of wire have gotten detached and are touching the other main wire. 7. Repeat Steps 1 through 6 for the other Russound In-Wall Speaker. AT THE AMPLIFIER END 1. Cut off excess wire, leaving enough to comfortably reach from the hole in the wall to your stereo system. -
Page 8: Final Assembly
3. Place speaker baffle in frame and attach with supplied screws. 4. Insert the Russound speaker grille by gently pressing it into place. In most installations, the grilles will fit tightly without causing vibra- tion. If any audible vibration does occur, or if your Russound speakers are ceiling mounted, you finally get to use the contents of that mys- terious packet with the black stuff wrapped in little white papers. -
Page 9: Taking Care Of Your New In-Wall Speakers
Impedance-Matching Volume Controls to Impedance- Matching Speaker Selectors. Ask you Russound dealer for details or simply write your request for a line catalog to Russound or FAX us at 603.659.5388 First, consult the owner’s manual that came with the amp or receiver. -
Page 10: Warranty
Needless to say, installing In-Wall speakers when a house is being built is far easier than doing it later. Russound offers a ‘Speaker Rough-In Kit”. The SB-3.6 Rough-In kit is designed to provide the drywall installers the cut-out for the In-Walls. -
Page 11: Technical Specifications
TECHNICAL SPECIFICATIONS SP622.1 Frequency Response: 63-21,000Hz Construction: 6.5" injection molded cone Dual voice coil woofer with rubber surround. Two 13mm mylar Dome tweeters Sensitivity: 88dB Min / Max Power: 10W/Ch / 70W/Ch Impedance: 8 ohm Frame Type: ABS plastic, paintable... - Page 12 D I S T R I B U T I O N & C O N T R O L S Y S T E M S 5 Forbes Rd. Newmarket, NH 03857, USA 603.659.5170 • Fax 603.659.5388 e-mail: tech@russound.com Fax-On-Demand: 603.659.5590 Come visit us at:...
Need help?
Do you have a question about the SP622.1 and is the answer not in the manual?
Questions and answers