1. Manuals
  2. Brands
  3. AVS Electronics Manuals
  4. Security System
  5. VECTOR Plus
  6. Installation manual

AVS Electronics VECTOR Plus Installation Manual

Bidirectional gsm interface
Hide thumbs
Table of Contents

Advertisement

Quick Links

Curtarolo (Padova) Italy
www.avselectronics.com
VECTOR Plus
Bidirectional
INTERFACE
INSTALLATION MANUAL
QUALITY
SYSTEM
ISO9001
IST0401V2/1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VECTOR Plus and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AVS Electronics VECTOR Plus

Summary of Contents for AVS Electronics VECTOR Plus

  • Page 1 Curtarolo (Padova) Italy www.avselectronics.com VECTOR Plus Bidirectional INTERFACE INSTALLATION MANUAL QUALITY SYSTEM ISO9001 IST0401V2/1...

  • Page 2: Table Of Contents

    ........... testing vector plus .

  • Page 3: Features

    VECTOR Plus interface allows receiving calls through the GSM channel, since, when an incoming call is detected by the GSM unit, a valid RING signal is generated at the simulated line terminals of VECTOR Plus, causing the ring detector of the dialler or the ringing bell of a telephone to be activated.

  • Page 5: Other Display Indications

    8 (blinking) : Indicates an incoming call through the GSM. Trouble and Fault messages: 0 = VECTOR Plus is not able to turn on the GSM unit. 1 = Wrong or missing serial comunication between VECTOR Plus and GSM unit.

  • Page 6: Dip Switches

    NOT supervised) PABX connection If VECTOR Plus interface were to be installed in premises where PABX equipment is present, requiring additional digits when dialling to reach external telephone line (Ex. 0 or 9): DIP 3 in OFF...

  • Page 7: Gsm Engine Connection

    GSM engine connection RV2 RV3 Modulo GSM engine PROG. RESET F1 F3.15A L250V TAMPER F2 F3.15A L250V OUT STATE BATT. TAMPER CENTR. CENTR. Connect the GSM engine to 30 pin female connector. Plugging in sim card / antenna jack GSM engine with upper side SIM Card holder: 1.

  • Page 8: Sms Functions

    SMS messages are sent to by default, otherwise differently specified in configuration parameter "1". Apart from the technical SMS, that are automaticly sent by VECTOR Plus once they has been enabled through the configuration numbers, the remaining SMS stored into the SIM card by the installer to communicate any kind of alarm or status information, can be sent through the VECTOR Plus interface only in "by command"...

  • Page 9: Parameters Programming (Sms By Command)

    NOTE 1: to enable sending an SMS by command when VECTOR Plus is not operating in GSM mode, simply shortcircuit to negative for a few seconds the "GSM" terminal of the equipment, while dialling the DTMF sequence for SMS activation.

  • Page 10: Dialler Programming To Send "By Command" Sms Messages

    NOTE 2: if the telephone number for SMS activation is not the first number "called" by the dialler, once the "GSM" input terminal of VECTOR Plus has received the pulse to negative, all telephone calls previous to the SMS activation number will be executed through the GSM channel, while successive ones will occur over PSTN line.

  • Page 11: Telephone Numbers On Mobile Phonebook

    Telephone numbers on mobile phonebook Posit.on Name Telephone number Posit on Name Telephone number M.add. saved M.add. saved SMS list SMS Description SMS Description 1 tecn. 2 tecn. 3 tecn.
  • Page 12 AVS ELECTRONICS S.p.A. Via Valsugana, 63 35010 (Padova) ITALY Tel. 049 96 98 411 Fax. 049 96 98 407 avs@avselectronics.com www.avselectronics.com AVS ELECTRONICS S.p.A. reserves the right to modify the technical and esthetical characteristic of the products at any time.

Table of Contents