Related Manuals for Runco DLC-2000HD
Summary of Contents for Runco DLC-2000HD
- Page 1 ’ ANUAL DLC-2000HD Projection System Liquid Crystal Projector & Pixel-For-Pixel Controller with Vivix Technology...
-
Page 3: Table Of Contents
Table of Contents Limited Warranty ... 1 Introduction ... 3 Warnings and Safety Precautions ... 4 Warning ... 5 Safety Tips ... 5 Indicator Lights ... 6 Top View ... 6 Front and Rear Panel Description ... 7 Front Panel... 7 Rear Panel ... -
Page 4: Limited Warranty
PROVIDING WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PERSONNEL. RIGHTS, LIMITS AND EXCLUSIONS: Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. - Page 5 IMPORTANT: WARRANTY REGISTRATION: Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified.
-
Page 6: Introduction
Congratulations on your purchase of the DLC-2000HD system! This system was designed to be a fully integrated system, which includes the DLC-2000HD Projector and the unique PFP™ Controller. This system is extremely easy to use, as all of the controls for the Projector have been integrated into the PFP Controller for ease of operation and control. -
Page 7: Warnings And Safety Precautions
Warnings and Safety Precautions CAUTION: To turn off main power, be sure to remove the plugs from power outlets. The power outlet sock- et should be installed as near to the equipment as possible, and should be easily accessible. REMARQUE: Pour mettre l’appareil hors circut, s’assurer de retirer la fiche de la prise d’alimentation. -
Page 8: Warning
· If the power cord is damaged or frayed in any way, electrical shock and/or fire may result. Please do not place objects on the power cord, and keep the cord away from heat-emitting devices. Should the power cord become damaged in any way, please contact your Runco dealer for a replacement cord. -
Page 9: Indicator Lights
Indicator Lights Top View The Projector has four lights which provide a status of the operation of the Projector. These are described below: Lamp warning: Lights up YELLOW when the lamp has reached its useable life expectancy (1500 hours). Temp warning: Flashes RED when the internal temperature is too high. -
Page 10: Front And Rear Panel Description
Front and Rear Panel Descriptions Front Panel IR RECEIVER Receives the infrared signal from the remote control. POWER BUTTON Turns the unit ON or OFF. The Main Power switch on the rear of the unit must be on first for this button to be active. POWER INDICATOR When the PFP Controller is ON, this LED will illuminate GREEN. -
Page 11: Rear Panel
This is for systems using serial (RS-232) to control the PFP Controller. COMLINK OUT The output of this jack must be connected to the ComLink input of the DLC-2000HD Projector. If this is not connected, neither the Controller or the Projector can operate. -
Page 12: Remote Control Description
Remote Control Description A. IR OUTPUT INDICATOR Illuminates when a button is pressed, indicating that an IR signal is being transmitted. B. POWER BUTTON Toggles the power on and off. For a discreet on or off command, you can use the direct access buttons (see 'J'). Note: When the main AC power switch is first turned ON, the Controller will go through an initiation cycle for approximately 15 seconds. -
Page 13: Menu Description And Navigation
Menu Description and Navigation Menu Tree INPUT SELECT Standard Video: > Composite S-Video Component High Definition: Component ASPECT RATIO SELECT Main Menu Through the Main Menu, you can easily switch sources and Aspect Ratios. To select a source, you may either use the direct access buttons on the remote (pg. 9) or the Left/Right buttons on the remote or Front Panel (pgs. -
Page 14: Specifications
Specifications DLC-2000HD Projector: Projector Type: Native Resolution: 1366 x 768 Lamp: 250W Metal Halide Inputs: RGB/Component Bandwidth: 180 Mhz (RGB) Power Requirements: 100-120 VAC, 200-240 VAC 50/60 Hz (export version) Current: 3.3A (100-120 VAC), 1.7A (200-240 VAC) Power Consumption: 360W Dimensions: Width: 16.310 in. - Page 15 Controller: Inputs: (1) Component, (1) S-Video, (1) Composite, (1) HDTV/Computer Input standards: NTSC/PAL/480p/720p/1080i/SVGA/XGA Output format: 1366 x 768 Bandwidth: Video inputs: 5.5 Mhz, HDTV/Computer: 100 Mhz Power Input: 120V (220V export model), 50/60 Hz Power Consumption: Control Options: RS-232, Infrared, Front Panel Operating Environment: 41°-95°F (5°-35°...
- Page 17 RUMA-006700 rev 11-03 Runco International 2900 Faber Street Union City, CA 94587 ph (510) 324-7777 fax (510) 324-9300 www.runco.com...