Page 1
Dual Digital Hybrid ADAM™, ADAM CS™, Zeus™ Intercom Systems - 1 5 - 1 2 - 1 0 d B 0 d B 9350-7638-000 Rev C 10/04 SSA-424 - 1 5 - 1 2 - 1 0 d B 0 d B...
Page 2
SHIPPING TO MANUFACTURER All shipments of RTS products should be made via United Parcel Service or the best available shipper, prepaid. The equipment should be shipped in the original packing carton;...
There is a power ON/OFF and call indicator at the left of the front panel. This indicator lights continuously when the SSA-424 is turned on and flashes when an incoming call signal is detected. The remainder of the front panel is divided into controls and indicators for the two separate hybrids, labeled SYSTEM A and SYSTEM B.
Warranty Card User Instruction Manual OUNTING Place the SSA-424 on a desktop, or install it in an equipment rack using an RTS MCP Rack Mount Kit. Several rack mount options are available (Figure2, page 8). There are no special ventilation require- ments for the SSA-424, but allow for ventilation around the power pack.
Page 8
Side-By-Side Rack Mount Configuration Using an MCP1 Rack Mount Kit Single-unit Rack Mount Configuration Using an MCP2 Rack Mount Kit Console Mount Configuration Using an MCP3 Console Mount Kit Tandem Configuration Using an MCP4 Tandem Mount Kit Figure 2. Rack mount configurations 8 SSA-424 U ANUAL...
2.4.2 1 You can directly connect standard Audiocom 1- channel cables. Connect one Audiocom channel to the J1A connector on the back of the SSA-424 (System A). Connect a second Audiocom channelto the J1B connector (System B). If your Audiocom system uses 2-channel cables, use a...
You can therefore connect the SSA-424 to powered Clear-Com cables, and it will not draw any power from the Clear-Com system. 2 On the SSA-424 front panel, set the System A and System B 2W CHAN SEL switches to position 2.
GPI input #1; however, you may use any other available GPI inputs and outputs. The Call Enable/Inhibit connection is optional. It gives you the ability to disable call signaling using a GPI output. However, when connecting to a Clear-Com intercom system, if an enable/ inhibit switch is not connected, a jumper must be installed as shown to enable call signaling.
Page 12
Table 2. UIO-256 GOI Inputs Connector (J7) Table 3. UIO-256 GPI Outputs Connector (J5) 12 SSA-424 U ANUAL c t i c t i...
The SSA-424 accepts a switch-contact input from the 4-wire system and then generates a call signal output to the 2-wire system. The SSA-424 also accepts an optional switch contact input to enable or inhibit call signaling between the 4-wire and 2-wire systems.
Operation ENERAL NSTRUCTIONS 1 Attach the power pack to the SSA-424, and apply power to all components. Confirm that the power indicator is lit on the SSA-424 front panel. 2 The power indicator flashes when a call signal is received fron a 2-wire line. The SSA-424 level displays should help to confirm which line is calling.
ETTINGS S301 controls the operating mode for System B and S302 controls the operating mode for System A. Settings are summarized in Table 4 16 SSA-424 U ANUAL 1 1 1 1 1 2 2 2 2 2 J5 POWER +5V 3A +15V 1.6A...
9 Remove the test signal. This completes the adjustment. IGNAL PTION Use these instructions to install a Call Signal Option Card in an SSA-424 that was originally ordered without it. 1 Disassemble the SSA-424 as previously de- scribed. 2 Assemble the standoffs to the circuit board using the supplied screws and lockwashers.