Roland MV-8000 Owner's Manual page 440

MIDI Implementation
●Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
ll, mm = Pitch Bend value: 00, 00H - 00, 40H - 7F, 7FH (-8192 - 0 - +8191)
* Controls the pitch bend change of the part that correspond to received MIDI channel
number.
■Channel Mode Messages
●All Notes Off (Controller number 123)
Status 2nd byte
BnH 7BH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When All Notes Off is received, all notes on the corresponding channel will be turned
off. However, if Hold 1 is ON, the sound will be continued until these are turned off.
●OMNI OFF (Controller number 124)
Status 2nd byte
BnH 7CH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
●OMNI ON (Controller number 125)
Status 2nd byte
BnH 7DH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received. OMNI ON
will not be turned on.
●MONO (Controller number 126)
Status 2nd byte
BnH 7EH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = mono number: 00H - 10H (0 - 16)
* The same processing will be carried out as when All Notes Off is received.
* In Performance mode, the Part Mono/Poly parameter (PERFORM/PART) will change.
●POLY (Controller number 127)
Status 2nd byte
BnH 7FH
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
* In Performance mode, the Part Mono/Poly parameter (PERFORM/PART) will change.
■System Realtime Message
●Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all
further messages. While monitoring, if the interval between messages exceeds 420 ms,
the same processing will be carried out as when All Sounds Off, All Notes Off and Reset
All Controllers are received, and message interval monitoring will be halted.
440
3rd byte
mmH
3rd byte
00H
3rd byte
00H
3rd byte
00H
3rd byte
mmH
3rd byte
00H
2. Data Transmission
■Channel Voice Messages
●Note off
Status 2nd byte
8nH kkH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note off velocity: 00H - 7FH (0 - 127)
●Note on
Status 2nd byte
9nH kkH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note on velocity: 01H - 7FH (1 - 127)
●Polyphonic Key Pressure
Status 2nd byte
AnH kkH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = Polyphonic Key Pressure: 00H - 7FH (0 - 127)
●Control Change
* By selecting a controller number that corresponds to the setting of parameters of
controllers (Assignable sliders), the MV-8000 can transmit any control change message.
❍Bank Select (Controller number 0, 32)
Status 2nd byte
BnH 00H
BnH 20H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
❍Modulation (Controller number 1)
Status 2nd byte
BnH 01H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Modulation depth: 00H - 7FH (0 - 127)
❍Breath type (Controller number 2)
Status 2nd byte
BnH 02H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
❍Portamento Time (Controller number 5)
Status 2nd byte
BnH 05H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Portamento Time: 00H - 7FH (0 - 127)
❍Data Entry (Controller number 6, 38)
Status 2nd byte
BnH 06H
BnH 26H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH