Related Manuals for Rockford Fosgate Punch Audiophile ND4-XFM
Summary of Contents for Rockford Fosgate Punch Audiophile ND4-XFM
- Page 1 AUDIO phile 1" NEODYMIUM TWEETER WITH HIGH PASS CROSSOVER ND4-XFM & ND8-XFM Owner's Manual ® ®...
- Page 2 Training Institute (RTTI). Please read your warranty and retain your receipt and original carton for possible future use. To add the finishing touch to your new Rockford Fosgate image order your Rockford accessories, which include everything from T-shirts and jackets to hats and sunglasses.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Specifications ... 1 ND4-XFM / ND8-XFM Neodymium Tweeter Contents ... 1 Introduction ... 2 Design and Features ... 2 TX-184N/188N High Pass Crossover ... 2 ND4 and ND8 Neodymium Tweeters ... 3 Flush Mounting the ND4/ ND8 Tweeters ... 4 Surface Mounting the ND4/ ND8 Tweeters ... -
Page 4: Specifications
Resonance Frequency Frequency Response TX-184N/TX-188N Crossover Network Crossover Frequency Crossover Slope Connections ND4-XFM/ND8-XFM NEODYMIUM TWEETER CONTENTS 1 pair ND4/ND8 Neodymium Tweeters 1 pair Flush Mount Cups 1 pair of surface mounting plates 1 pair TX-184N/188N High Pass Crossovers Mounting Hardware... -
Page 5: Introduction
We suggest you save this manual for future reference. We strongly recommend you have your Authorized Rockford Fosgate Dealer install the ND4/ND8 Neody- mium tweeters. If you do choose to install the tweeters yourself, please be sure to read the entire manual before beginning. -
Page 6: Nd4 And Nd8 Neodymium Tweeters
The ND4 and ND8 Neodymium Tweeters are designed for optimum smooth frequency response. This goal, as with all other Rockford Fosgate products, is achieved by utilizing "high quality, high-end" components. Neodymium The high ionic compound of neodymium enables a... -
Page 7: Flush Mounting The Nd4/ Nd8 Tweeters
FLUSH MOUNTING THE ND4 /ND8 TWEETERS The following instructions explain how to mount the ND4/ND8 Tweeters in a flush mount application. 1. Cut a 2-1/8" (54mm) diameter mounting hole. 2. With the keyway pointing up, insert the flush mount Front View Key hole pointing up Flush Mount Tweeter... -
Page 8: Surface Mounting The Nd4/ Nd8 Tweeters
SURFACE MOUNTING THE ND4 /ND8 TWEET- The following instructions explain how to surface mount the ND4/ND8 Tweeters. 1. Place the mounting plate on the surface that the 2. Drill a 1/4 inch (6.4mm) hole for the wire access. 3. Route the hook up wire through the center hole. 4. -
Page 9: Wiring The Nd4/Nd8 Neodymium Tweeter
WIRING THE ND4/ND8 NEODYMIUM TWEETER TX-184N/188N TX184N/188N Input – Input from Amplifier lock in place. Note: The color coded wire is connected to the positive (+) terminal on Output – > – > To ND4/ND8... -
Page 10: Replacing The Nd4/Nd8 Dome
REPLACING THE ND4/ND8 DOME both the ND4 and ND8. Disassembly 1. Gently remove tweeter assembly from mounted 2. Disconnect the tweeter wire harness, at the .110 3. Remove the "strain relief clip" from the back of 4. Carefully grasp one of the wires leading into the 5. - Page 11 dome. 3. Once the replacement Coil/Dome Assembly and Magnet Enclosure are together, gently pull the voice coil wires extending out from the bottom of the Magnet Enclosure until any extra slack has been eliminated. Wrap the voice coil wires around the edge of the Magnet Enclosure away from the metal parts.
-
Page 12: Nd4/Nd8 Neodymium Assembly Diagram
ND4/ND8 NEODYMIUM ASSEMBLY DIAGRAM... -
Page 13: Warranty Information
WARRANTY Rockford Fosgate warrants all loudspeakers to the original purchaser for a period of two (2) years parts and labor, providing the product was purchased from an Authorized Rockford Fosgate Dealer. Speakers found to be defective during the warranty period will be repaired or replaced (with a product deemed to be equivalent) at Rockford Fosgate's discretion. - Page 14 Rockford Fosgate A Division of Rockford Corporation 546 South Rockford Drive Tempe, Arizona 85281 U.S.A. In U.S.A. (602) 967-3565 In Canada, call Korbon (416) 567-1920 In Europe, Fax (49) 4207-801250 CP-8675 (6/93)