RocketFish RF-WHD100 Quick Setup Manual

WirelessHD® Adapter
RF-WHD100
Important safety information
This guide contains important safety instructions. Read and follow all
instructions carefully while installing and using the adapter. Read this
guide thoroughly before trying to unpack, install, or use your adapter.
Save these instructions in a readily accessible place.
• Caution: Always treat your adapter with care and keep it in a clean
and dust-free place.
• Do not expose your adapter to liquid or moisture or humidity.
• Do not expose your adapter to temperatures above 104°F (40°C)
when unit is operated.
• Do not drop or throw your adapter.
• Do not attempt to disassemble or modify your adapter. Only
authorized personnel should perform service.
• Your adapter is not water-resistant. Keep it dry.
• Do not use a different AC adapter to avoid unit burn or smoke.
Package contents
• 60 GHz WirelessHD transmitter
• 60 GHz WirelessHD receiver
• HDMI cables (2)
Transmitter and receiver front panels
1 Link LED (blue)
On—Indicates the receiver is linked to the transmitter.
Off—Indicates devices are not linked. Reset both devices.
Blinking—Waiting for a link.
2 Weak LED (green)
On—Indicates the signal is weak. (The Strong LED will be off.)
Off—Indicates there is no link or no signal.
3 Strong LED (green)
On—Indicates the signal is strong. (The Weak LED will be on.)
Off—Indicates the signal is weak. (The Weak LED will be on.)
Warning: If all four LEDs are blinking at the same time, the internal
cooling fan is not working. Turn off the adapter and contact
Rocketfish customer service.
4 Power indicator
On—Indicates power is connected and turned on.
Off—Indicates power is turned off.
Side panel
5 RESET AND CFG
These buttons are for service at the factory only, please do not
QUICK SETUP GUIDE
press them.
• Power adapters (2)
• Base mounting brackets (2)
• Quick Setup Guide
RESET CFG
Transmitter and receiver back panels
6 DC-IN
Connect the power adapter to this jack and to a power outlet.
7 Power switch
Press the Power switch to turn the unit on.
8 HDMI
Used to connect the HDMI cables from the source component to
the transmitter, and from the receiver to the TV/Projector.
Setting up
To attach the base stands:
1 Align the holes on the
base stand with the
mounting tabs on the
bottom of the
transmitter or receiver.
2 Press the stand down,
then slide it to the left
so the tabs hold the
stand in place.
To connect the transmitter and receiver:
1 Connect one HDMI cable from the output
of the source component (Blu-ray/DVD
player, Gaming console, Computer, etc.) to
the input on the back of the transmitter unit.
Note: The transmitter can be used in
conjunction with Rocketfish model
RF-HDMI4, 4-way HDMI Selector, to
send HD signals wirelessly from up
to four source components.
Note: For connection to a computer
with a DVI output, use Rocketfish
model RF-G1174 HDMI-to-DVI Adapter.
2 Connect the other HDMI cable from the
output on the back of the receiver unit to
an available HDMI input on the HDTV or
HD Projector.
3 Connect the power cords to the
DC IN jacks on the transmitter and
receiver and to a power outlet.
4 Turn on the connected devices, then
press the power switches on the
transmitter and receiver to the ON
position.
Positioning the transmitter and receiver
For best results, the transmitter and receiver should:
• Face each other within the same room
• Be no more than 33 feet (10 meters) apart
• Be on the same level (one should not be higher than the other)
• In open spaces (not in a cabinet or an enclosed shelf)
Note: If you begin to see your video breaking up, try repositioning
the device providing the transmitter as many open paths to the
receiver as possible.