Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Virtual Reality VR3 VR500CS-BT
Summary of Contents for Virtual Reality VR3 VR500CS-BT
-
Page 2: Table Of Contents
Welcome! Dear Customer, CONGRATULATIONS. The VR500CS-BT MP3/CD Player with AM/FM Receiver, USB Port and SD Card Slot, Electronic Anti-Shock (ESP) & Fold-down Detachable Face, when used as described, will give you years of dependable service in your car, truck, RV, or mini-van. We have taken numerous measures in quality control to ensure that your product arrives in top condition and will perform to your satisfaction. -
Page 3: Precautions
• This unit will only play the following discs. • This unit does not play files that have Digital Rights Management(DRM). • If you have files that have Digital Rights Management(DRM) you should consult with the vendor that you purchased files from for instructions on proper use. Type of disc CD, MP3, &... -
Page 4: Notes On Installation
• Disconnect negative battery terminal before starting installation. Consult the vehi- cle’s owner’s manual for proper instruction. • The unit is designed for a 12Volt DC negative ground operation system only. Before installing the unit, confirm that your vehicle is a 12Volt DC negative ground system. •... -
Page 5: Before You Install
Automotive audio equipment installations can be challenging at times, even to the most experienced of installation technicians. If you are not confident working with electrical wiring, removing and re-installing interior panels, carpeting, dashboards or other components of your vehicle, please call your dealer in order to have the unit professionally installed. -
Page 6: Installation (Din Front Mount)
DIN FRONT-MOUNT (Method A) 1. Dashboard 2. Mounting Sleeve Fig. 1 Follow the diagram in Fig. 2 for installing the rear mounting strap to the head unit. The rear mounting strap will help keep the head unit from moving around inside the dashboard. Insert fingers into the groove in the front of frame to remove it. - Page 7 DIN REAR-MOUNT (Method B) Installation using the screw holes on both sides of the unit. PARTS 2 Keys 1 Hex Nut 1 Mounting Sleeve (not shown) 2 Lock Washers 1 Sheet Metal Screw 1 Metal Support Strap 1. Screw holes on the side of the unit. 2.
-
Page 8: Installation (Vehicle's Brackets)
MICROPHONES The VR500CS-BT has the ability to use two microphones. One microphone is built-in, the other is a remote microphone. Built-In Microphone The built-in microphone is located on the front right side of the unit. There is no setup required for this microphone and it is tuned to pick-up the voices of the front and rear seat passengers. -
Page 9: Wiring Connections
Make sure you have good chassis ground. A good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good electrical connection. ANTENNA SOCKET Sub W. -
Page 10: Location Of The Controls
1. Answer/ Green Phone 2. Volume/SEL/Enter 3. Disc Slot 4. Liquid Crystal Display (LCD) 5. 0-9, #, & * Key Pad buttons 6. Random / No. 4 7. No.1 / Top 8. No.5 / Down 10 9. Intro/No. 2 10. Eject 11. -
Page 11: Remote Control
Operating the Remote Control Aim at the front panel of the CD Receiver. The maximum operating distance is about 6M. Make sure that the signal path is not obstructed. Do not drop or throw the remote control. Do expose the remote control to direct sunlight or place next to a heating unit or other heat source. -
Page 12: Basic Operation
1. Tuning the Unit On / Off Press any Button to turn the unit on, the dis- play will show a message WELCOME to in- dicate it is ready for use. Press the POWER button for 2 seconds to turn the unit off. 2. -
Page 13: Bluetooth
Before Connecting Turn the VR500CS-BT ON, then turn your cell phone’s Bluetooth Function ON. 1. Pairing 1. Press the “PHONE” button. 2. Press and hold the Volume Knob until you see “DISP OFF”, 3. Press the Volume Knob repeatedly to cycle through to “PAIRING”. - Page 14 10. Recently Received Calls After connecting with cell phone; 1. Press the “PHONE” button. 2. Press and hold the Volume Knob until you see “OUT NUM”, then press the Volume Knob until the display shows “IN NUM”. 3. Press and hold the Volume Knob and the display will show the most recent received call.
-
Page 15: Radio Operation
1. Choose Radio Band Press the BND•ID3 Button anytime to ac- cess the radio function. The unit comes with five bands - three FM (FM1, FM2, and FM3) and two AM (AM1 and AM2) Band selects. Each of the five bands can store up to six preset stations, for a to- tal of 30 preset memory stations. -
Page 16: Cd Operation
1. AF - Alternative Frequency Press the AF button and the unit will choose the strongest FM signal for the selected station, so that you do not have to re-tune the station when driving between different transmitter coverage areas. When AF is on, it means RDS information is received;... -
Page 17: Mp3/Wma Operation (Cd)
cally switch to Radio Mode. 2. Multi-Session CD Reading This unit can read multi-session CDs. The multi-session reading will be activated automatically if the player detects a file that is written in multi-session format. Press and hold the Volume Knob until “DSP OFF” is shown on the LCD, then press the Volume Knob to cycle through the menu selections until “MULT OFF”... -
Page 18: Usb/Sd Card Operation
Press the |<< Button to go to a previous track. Track numbers will be shown on the display. Press and hold the |<< Button to fast reverse. Disc will play normally when the >>| or |<< Button is released. 4. Play/ Pause CD On the Remote or Head Unit, press the “BND•ID3”... -
Page 19: Search Modes For Mp3/Wma Files
4. Scanning Tracks On the Remote or Head Unit, press the 2 / I NT Button to play the first 10 seconds of each track. Press this button again to resume playback. 5. Repeat On the Remote or Head Unit, press the F/PS / R PT Button to repeat the same track continuously. -
Page 20: Aux In, Rca, & Subwoofer Control
1. RCA Output The RCA Output Jacks are on the back of the unit. (Refer to Wiring Diagram) This out- put is for connecting an amplifier, equalizer, or other audio componement that requires a pre-amp out connection. (Red = Right, White = Left) Follow the manufacturers in- structions for the audio component that you are connecting. -
Page 21: Specifications
Specifications GENERAL Operating Power ... 12 Volts DC, Negative Ground Output Wiring ...Designed for using four speakers only Maximum Output Power ... 4x45 Watts RMS Output Power ...4x16 Watts@4ohms<1% THD+N>60dB Ref. 1 Watt Output@14.4VDC RCA line out ... low-level outputs - 1000MV Output Impedance ...Compatible 4 to 8 Ohm Speakers Fuses ... -
Page 22: Warranty
VIRTUAL REALITY VIDEO LABS free performance. VIRTUAL REALITY VIDEO LABS® warrants, to the original purchaser, that its products are free from defects in material and workmanship for 30 days from the date of original purchase, as part of our commitment to product excellence. VIRTUAL REALITY VIDEO LABS the designs, materials or production methods of its existing products.