18 volt reciprocating saw variable speed (32 pages)
Summary of Contents for RIDGID R844
Page 1
When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for buying a RIDGID product. SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATOR’S MANUAL...
TABLE OF CONTENTS n Introduction ...2 n General Safety Rules ... 3-4 n Specific Safety Rules...4 n Safety Rules for Charger ...5 n Symbols... 6-7 n Features...8 n Assembly ...9 n Operation ... 10-13 n Maintenance ...14 n Warranty ...15 n Customer Service Information...16 INTRODUCTION This tool has many features for making its use more pleasant and enjoyable.
Use battery only with charger listed. MODEL BATTERY PACK R844 130254003, 130252004 n Do not abuse the cord. Never use the cord to carry the charger. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately.
GENERAL SAFETY RULES SERVICE n Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. SPECIFIC SAFETY RULES n Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring.
SAFETY RULES FOR CHARGER WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. n Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME Volts Amperes Hertz Watt Minutes Alternating Current...
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL DANGER: WARNING: CAUTION: CAUTION: SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair.
FEATURES PRODUCT SPECIFICATIONS Length of Stroke...1-3/16 in. Strokes Per Minute...0-2500/min. Motor ... 18 Volt DC Switch... Variable Speed With Brake Charger Rating ... 120 V, 60 Hz, AC only Charge Rate ... 30 minutes BASE (SHOE) ASSEMBLY BLADE BLADE CLAMP LOCK / RELEASE CHARGER KNOW YOUR RECIPROCATING SAW...
ASSEMBLY UNPACKING This product has been shipped completely assembled. n Carefully remove the tool and any accessories from the box. n Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
OPERATION WARNING: Do not allow familiarity with your tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.
Page 11
OPERATION OPERATION LED FUNCTION OF CHARGER See Figure 4. INDICATOR Power Evaluate Evaluate Evaluate Evaluate Charging Full POWER INDICATOR EVALUATE INDICATOR CHARGING INDICATOR FULL INDICATOR BATTERY PACK Without battery pack Hot battery pack Flashing Cold battery pack Flashing Deeply discharged Flashing Thermistor shorted Flashing...
OPERATION TO INSTALL BATTERY PACK See Figure 5. n Place the battery pack in the saw aligning raised rib on battery pack with groove in the saw's battery port. n Make sure the latches on each side of the battery pack snap into place and the battery pack is secured to saw before beginning operation.
Page 13
OPERATION GENERAL CUTTING See Figure 8. Hold the saw firmly in front of and clearly away from you. Make sure the saw blade is clear of any foreign material. Be sure the material to be cut is held firmly. Small work pieces should be securely clamped in a vise or with clamps to the work bench or table.
Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at a RIDGID authorized service center. BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING...
2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.
R844 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com.