Siemens Simatic S7-200 System Manual page 463

Errors
compile rule violations, C-4
fatal, C-2
Network Read/Network Write, 10-133
non-fatal, C-3, C-4
PID loop, 10-62
run-time programming, C-3
SMB1, execution errors, D-2
ET 200, manual, G-3
European Community (EC) certification, A-3
Examples
Add to Table, 10-73
analog adjustment, 8-8
And, Or, Exclusive Or, 10-105–10-107
ASCII to HEX, 10-113
block move, 10-71–10-73
calculating power requirements, 2-15
call to subroutine, 10-89–10-91
comparison contact instructions, 10-9
contact instructions, 10-6
Convert and Truncate, 10-109
counter, 10-20
data block, 3-32
Decode/Encode, 10-111
decrement, 10-67
First-In-First-Out, 10-75
For/Next, 10-91–10-93
GSD file, 9-24
High-Speed Counter, 10-36
high-speed counter
operation of HSC0 Mode 0 and HSC1 or
HSC2 Modes 0, 1, or 2, 10-23
operation of HSC1 or HSC2 Modes 3, 4,
or 5, 10-24
operation of HSC1 or HSC2, Modes 6, 7
or 8, 10-24
operation of HSC1 or HSC2, Modes 9,
10, or 11, 10-25
operation with Reset and Start, 10-23
operation with Reset and without Start,
10-22
I/O numbering, 8-2, 8-3
increment, 10-67
initialization of HSC1, 10-21
Interrupt Routine instructions, 10-122
Invert, 10-107–10-109
Jump to Label, 10-87–10-89
Last-In-First-Out, 10-74
logic stack, 10-101–10-103
loop control (PID), 10-63–10-65
math, 10-54
memory fill, 10-72–10-74
S7-200 Programmable Controller System Manual
C79000-G7076-C230-02
move and swap, 10-70–10-72
MPI card with master/slave, 3-9
Network Read/Network Write,
10-134–10-136
on-delay timer, 10-17
output instructions, 10-12
parameter block, 5-11
program for DP communications, 9-26
Pulse Train Output, 10-45
Pulse width modulation, 10-47
Real number conversion instruction, 10-109
retentive on-delay timer, 10-18
sample program, 4-2
Segment, 10-111
Sequence Control Relay, 10-93–10-98
conditional transitions, 10-98
convergence control, 10-96–10-99
divergence control, 10-94
set up timed interrupt, 6-9
shift and rotate, 10-83–10-85
shift register bit, 10-79–10-81
Status/Force Chart, 3-34
Stop, End, and Watchdog Reset,
10-86–10-88
Symbol Table, 3-36
Table Find, 10-77
TD 200s added to network, 9-14
token passing network, 9-28
transmit instructions, 10-130
Truncate, 10-109
Exclusive Or Byte instruction, 10-102
Exclusive Or Double Word instruction, 10-104
Exclusive Or Word instruction, 10-103
Execution times
effect of analog I/O, F-1
effect of indirect addressing, F-1
effect of power flow, F-1
statement list instructions, F-1–F-11
Expansion cable
See also I/O expansion cable
installation procedure, 2-5–2-7
Expansion module. See EM231, etc.
Index
Index-13