Door Glass Adjustment; Door Glass Outside Moulding And Weatherstrip Removal; Front Door Vent Wing Assembly Removal And Installation; Tail Light Assembly - Chrysler 1956 Imperial Service Manual

Installation
Installing the Sliding Glass - Tilt the sliding
glass forward and insta ll through door glass
opening. Install the shoulder stud s, connect win-
dow regulator arms in slots of sliding glass
frame and secu re with retainer washers. 'f ight.
en window lift motor mounting bracket screws
and install the upper stops.
Installing the Rota ting Glass _ Install the ro-
tating glass and pivot step bolt. Install door
handle.
DOOR GLASS ADJUSTMENTS
To adjust the sliding glass fore and aft, loosen
the shoulder studs and move the sliding glass
us!'embly as required. Tighten lock nuts after
adj ustment. To move the sliding glass up or
down, turn the shoulder studs in or out. To tilt
the glass in or out, ad just the two shoulder
studs on either side, as necessa ry, to control the
operation. Tighten lock nuts after adjustment.
The rotating glass can be moved in or out after
loosening the two screws on the pivot bearing.
The r otating glass cnn
be
moved fore or aft,
and up or down after loosening the three screws
on the bracket. After the glass is properly
aligned, tighten the screws secu rely. 'fo align
the division bar on the sliding glass and the
rotating glass, loosen the two screws on the
pivot control track. line up the division hal' and
t ighten screws securely.
After sliding glass and rotating glass are in-
stalled and adjustments are made as required,
hook up and install the remote control assembly
and install the outs ide belt line moulding. Posi-
tion the glass lower sto ps an d secure with
screws. Install trim panel and door hardware.
Connect the battery.
REPLACEMENT OF DOOR GLASS
OUTSIDE MOULDING AND
W EATHERSTRIP (FRONT DOOR)
Remove door hardwnre and trim panel. Loosen
down stop mounting screws <lnd lower the down
stops. Lower the window glass as far as it win
go. Remove the outside belt line moulding at-
taching screws nnd the moulding. Remove the
moulding suppor t and weHtherstrip to door with
attaching screws nnd in;:;tall outside belt line
moulding, tightening the attaching screws se-
curely. Raise the window, place the down stops
position and tighten mounting screws securely.
Install trim panel and door hardware.
76
FRONT DOOR VENT WING ASSEMBLY
Re moval and Installation
These procedures are essentially the same as
those for 1955 Models,
except
that the outside
belt line moulding must be removed to expose
the outer vent wing attaching bolt. Also, remove
the nut on insi de of door under weather strip
and the screws on the inside door reinforcement.
TAIL LIGHT ASSEMBLY (ALL MODELS)
This assembly consists of a plate and three indi-
vidual units. T he top unit comprises the tail
light, stop light and directional signal light ; the
center unit is the back-up light, and the bottom
unit consists of a reflector and another tail light.
Each unit is attached to the plate of the tail
light assembly by two scr ews (accessible inside
luggage compa rtment). The plnte is attached to
the fender by five screws. Th e four screws in
the flat base are accessible inside the luggage
co mpartment. The other screw at the upper
peak of the assembly is accessible from outside
the ca r. Anyone of the three units can be easily
removed for servicing.
Replacement of Tail Light Assembly Lens es
To replace a lens of a unit o[ the tail light as-
sembly, remove the unit attaching screws (ac-
cessible inside luggage compartment). Pull unit
from plate (from outside ca r, Figure 11) , re-
move lens and replace. Lens is attached to as-
sembly frame with attaching screws.
The deck lid on the 1956 Models are aligned
and adjusted as outlined in the 1955 D-15431
Shop Manual.
Fig. 11 - Removi ng or
In~lolling
To illomp Assembly