Canon MX7600 Service Manual page 8

of the print head.
Multiple ink tanks of [1681] U071 More than one ink tank of the
the same color
installed.
Ink tank in a wrong [1680] U072 Some ink tanks are not
position.
Warning: The ink [1700,
absorber becomes 1701]
almost full.
The connected digital [2001]
camera or digital
video camera does
not support Camera
Direct Printing.
Automatic duplex [1310]
printing cannot be
performed.
Failed in automatic [2500]
print head alignment.
Dirty paper feed [2600]
roller.
Ink tank not [1684] U140 The following ink tank cannot
recognized.
Ink tank not [141#] U150 The following ink tank cannot
recognized.
No Clear ink at all [1693] U165 The clear ink has run out.
No Clear ink at all, [1694] U166 The clear ink has run out.
and the error cannot
be cleared.
No ink (no raw ink). [1688] U171 The ink has run out. Stop
following color is installed.
installed in place.
--- Contact the support center or
service center for ink absorber
replacement. Press [OK] to
continue printing.
--- The device may be
incompatible. Remove the
device and check the manual
supplied with the connected
device.
--- This paper is not compatible
with duplex printing. Remove
the paper and press [OK].
--- Auto head align has failed.
Press [OK] and repeat
operation. <See manual>
--- The transport unit may not be
clean. Perform sheet cleaning.
<See manual>
be recognized.
(Applicable ink tank icon)
be recognized.
(Applicable ink tank icon)
Replace the ink tank.
Replace the ink tank.
printing, then
replace the ink tank.
Replace the wrong ink tank(s) with the correct one(s).
Install the ink tank(s) in the correct position.
Replace the ink absorber, and reset its counter. [See
Adjustment / Settings, (5) Service
Pressing the OK button will exit the error, and enable
printing without replacing the ink absorber. However,
when the ink absorber becomes full, no further printing
can be performed unless the applicable ink absorber is
replaced.
Remove the cable between the camera and the machine.
The paper length is not supported for duplex printing.
Press the OK button to eject the paper being used at error
occurrence.
Data which was to be printed on the back side of paper at
error occurrence is skipped (not printed).
Press the OK button to clear the error, then perform the
automatic print head again.
(In the MX7600, use plain paper.)
When the time to perform periodic cleaning of the paper
feed rollers comes, the message is displayed for several
seconds during printing.
A non-supported ink tank is installed (the ink tank LED is
turned off). Install the supported ink tanks.
A hardware error occurred in an ink tank (the ink tank
LED is turned off). Replace the ink tank(s).
Replace the Clear ink tank, or press the Stop/Reset button
to clear the error without replacing the Clear ink tank.
When the Stop/Reset button is pressed, printing being
performed at error occurrence is cancelled.
Without the Clear ink, the print quality on plain paper
becomes significantly low, and the paper feed mechanism
of the cassette can be damaged. For this reason, printing
on plain paper cannot be performed unless the applicable
Clear ink tank is replaced with a new one.
If the Clear ink is completely used up when the machine
is forcibly turned off, such as by disconnecting the power
cord before the machine is turned off by the ON/OFF
button, the error may not be cleared. Replace the Clear
ink tank with a new one.
The PGI-7BK ink is used up (the ink tank LED flashes).
Press the Stop/Reset button to stop printing, replace the
empty ink tank(s), then resume printing.
Printing with an empty ink tank can damage the machine.
To continue printing without replacing the ink tank(s),
press the Stop/Reset button for 5 sec. or longer to disable
the function to detect the remaining ink amount. After the
operation, it is recorded in the machine that the function
to detect the remaining ink amount was disabled.
6 / 65
3-3.
mode.]