Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ResMed VPAP AUTO 25
Summary of Contents for ResMed VPAP AUTO 25
- Page 1 VPAP™ Auto 25 VPAP™ ST VPAP™ S Positive AirwAy Pressure device User Guide English...
- Page 2 NZ 406925, NZ 406926, NZ 406927, NZ 406928, US D544598, US D557406, US D557407, US D560795, US D561891. Other designs pending. SmartStart, TiCONTROL, VPAP, and Vsync are trademarks of ResMed Ltd and SmartStart and VPAP are registered in U.S. Patent and Trademark Office.
-
Page 3: Table Of Contents
The VPAP System Masks Humidifier ResScan Data Card Supplemental Oxygen Using the VPAP Auto 25, VPAP ST & VPAP S Setting up your VPAP Attaching a H4i Humidifier How to Use the Control Panel Using the Menus How to Select the Mask Type SmartStart™... -
Page 4: Introduction
• Power cord • Travel bag • ResScan™ Data Card. Optional components include: • 9’9” (3 m ) air tubing • DC/DC converter 24V/50W • ResMed Oxygen Connector Port. ST and the VPAP S are indicated for the treatment Introduction... -
Page 5: Masks
Masks The following ResMed mask systems are recommended for use with these devices: Mask Type Nasal Masks Nasal Pillows Systems Full Face Masks For information on using masks, see your mask manual. For the latest available masks, see www.resmed.com. Humidifier If you are experiencing dryness of the nose, throat or mouth, the H4i heated humidifier is recommended for use with these VPAP devices. -
Page 6: Supplemental Oxygen
Supplemental Oxygen The VPAP Auto 25, VPAP ST and VPAP S are designed to be compatible with the following levels of supplemental oxygen usage: • Up to 4 L/min in VAuto mode • Up to 15 L/min in CPAP , S, ST and T modes. -
Page 7: Attaching A H4I Humidifier
Attaching a H4i Humidifier The H4i humidifier attaches to the front of a VPAP Auto 25 to provide heated humidification. These devices automatically detect the presence of the H4i and no other accessories are required for its use. -
Page 8: Using The Menus
RAMP: 10min menu MASK: ULTRA exit change EPR LEVEL: 1 exit change USED: 0090hrs exit 006/002 days SW: SX3650201 exit Using the VPAP Auto 25, VPAP ST & VPAP S CPAP, S, ST & T modes exit exit exit exit... -
Page 9: How To Select The Mask Type
How to Select the Mask Type Scroll to MASK and select require. The following table shows the setting that should be selected for each mask: Settings ULTRA MIR FULL ACTIVA SWIFT STANDARD MIRAGE How to change the EPR level (CPAP mode) Expiratory Pressure Relief (EPR) can be used to improve your comfort level when breathing out during treatment. -
Page 10: Starting Treatment
RR: 15 Leak and breath information VT: 680 TiMx 2.0 Inspiration information 1: 1.6 This screen only displays if exit ResLink and an oximeter are connected Using the VPAP Auto 25, VPAP ST & VPAP S . If your clinician... -
Page 11: Using The Mask-Fitting Feature
Using the Mask-Fitting feature The VPAP Auto fit your mask properly. The mask-fitting feature delivers air pressure for a three- minute period, prior to starting treatment, for checking and adjusting your mask fit to minimize leaks. To use the mask-fitting feature: Fit your mask as described in the mask user instructions. -
Page 12: Using The Data Card
If your clinician has told you to use the Data Card to update the settings on your device and the “Settings Success” message does not appear, contact your clinician immediately. device Using the VPAP Auto 25, VPAP ST & VPAP S... - Page 13 Note: You should not use your VPAP device while the aircraft is taking off or landing. Use with DC Power You must use a ResMed DC/DC converter 24V/50W to connect your VPAP to a 12V or 24V DC power source. Contact your equipment supplier or ResMed for details.
-
Page 14: Cleaning And Maintenance
Cleaning and Maintenance You should regularly carry out the cleaning and maintenance described in this section. Refer to your mask and humidifier manuals for detailed instructions regarding the care of those devices. Daily Disconnect the air tubing and hang it in a clean, dry place until next use. Weekly Remove the air tubing from the VPAP device and the mask. -
Page 15: Servicing
Servicing This product should be inspected by an authorized ResMed service center five years from the date of manufacture. Prior to this, the device is intended to provide safe and reliable operation provided that it is operated and maintained in accordance with the instructions provided by ResMed. -
Page 16: Troubleshooting
Troubleshooting If there is a problem, try the following suggestions. If the problem cannot be solved, contact your equipment supplier or ResMed. Do not attempt to open the device. Problem/Possible Cause No display Power is not connected. Insufficient air delivered from the VPAP device Ramp or Settling time is in use. - Page 17 If this does not clear the message, disconnect the power cord and then reconnect it to restart the device. (where Exxxx Call Service Record error number and contact your ResMed service center. HIGH LEAK!!! Adjust Mask Check that your air tubing is connected properly. Adjust headgear.
-
Page 18: Technical Specifications
Technical Specifications Operating pressure range Maximum single fault steady state pressure Pressure measurement tolerance Flow measurement tolerance VAuto mode S, ST and T modes CPAP mode DECLARED DUAL-NUMBER NOISE EMISSION VALUES in accordance with ISO 4871: Sound pressure level Sound power level Dimensions (L x W x H) Weight Power supply... -
Page 19: General Warnings And Cautions
If the oxygen has been left on, turn off the device, then wait 30 minutes before turning on the device again. • Do not use the VPAP Auto 25, VPAP ST or VPAP S if there are obvious external defects or unexplained changes in performance. •... - Page 20 Guidance and Manufacturer’s Declaration – Electromagnetic Emissions and Immunity Guidance and manufacturer’s declaration – electromagnetic emissions The VPAP Auto , VPAP ST and VPAP S devices are intended for use in the electromagnetic environment specified below. The customer or the user of the VPAP device should assure that the device is used in such an environment. Emissions test RF emissions CISPR11 RF emissions CISPR 11 with serial adapter...
- Page 21 Guidance and manufacturer’s declaration – electromagnetic immunity The VPAP device is intended for use in the electromagnetic environment specified below. The customer or the user of the VPAP device should assure that the device is used in such an environment. IEC60601-1-2 test Immunity test level...
-
Page 22: Limited Warranty
ResMed shall not be responsible for any incidental or consequential damages claimed to have occurred as a result of the sale, installation or use of any ResMed product. Some regions or states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.