Remington 76728K, 099178H, 100089-06, 100089-08,107709-01,075762J, 098031J, 099039J, 100089-04, 100089-05, 100089-07, 107714-02,104316-04, Owner's Manual

Remington electric chain saw owner's manual
Hide thumbs Also See for 76728K, 099178H, 100089-06, 100089-08,107709-01,075762J, 098031J, 099039J, 100089-04, 100089-05, 100089-07, 107714-02,104316-04,:

Advertisement

ELECTRIC CHAIN SAW
OWNER'S MANUAL
LNT-2: 076728K, 099178H, 100089-06, 100089-08, & 107709-01
EL-7: 075762J, 098031J, 099039J, 100089-04, 100089-05,
100089-07, & 107714-02
Pole Saw: 104316-04 (8"), 106890-01(10")
Pole Saw Assembly: 104317 (8"), 106821 (10")
IMPORTANT: Read and understand this manual before assembling or
operating this chain saw. Improper use of saw can cause severe
injury. Keep this manual for future reference.
MODELS
®
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 76728K, 099178H, 100089-06, 100089-08,107709-01,075762J, 098031J, 099039J, 100089-04, 100089-05, 100089-07, 107714-02,104316-04, and is the answer not in the manual?

Questions and answers

Summary of Contents for Remington 76728K, 099178H, 100089-06, 100089-08,107709-01,075762J, 098031J, 099039J, 100089-04, 100089-05, 100089-07, 107714-02,104316-04,

  • Page 1 ELECTRIC CHAIN SAW OWNER’S MANUAL LNT-2: 076728K, 099178H, 100089-06, 100089-08, & 107709-01 EL-7: 075762J, 098031J, 099039J, 100089-04, 100089-05, 100089-07, & 107714-02 Pole Saw: 104316-04 (8"), 106890-01(10") Pole Saw Assembly: 104317 (8"), 106821 (10") IMPORTANT: Read and understand this manual before assembling or operating this chain saw.
  • Page 2: Before Operating Saw

    ELECTRIC CHAIN SAW SAFETY WARNINGS Make certain you read and un- derstand all Safety Warnings on pages 2 and 3. Improper use of this chain saw can cause severe injury or death from fire, electri- cal shock, body contact with moving chain, or falling wood.
  • Page 3: Maintenance And Storage Of Chain Saw

    SAFETY WARNINGS KICKBACK WARNING: Kickback may oc- cur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse re- action, kicking the guide bar up and back towards the operator.
  • Page 4: Electric Chain Saw

    ELECTRIC CHAIN SAW CHAIN SAW NAMES AND TERMS Process of cutting a felled tree or Bucking log into lengths. Process of cutting down a tree. Felling Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut.
  • Page 5: Product Identification

    PRODUCT IDENTIFICATION Rear Handle Rear Hand Guard Power Cord Front Handle Spike Motor Housing Figure 2 - Electric Chain Saw 107990 OWNER’S MANUAL Front Hand Guard Guide Bar Nose Chain Guide Bar Sprocket Cover Scabbard Oil Level Sight Hole (located on saw body, hidden by front handle) Oil Cap With Squeeze Bulb...
  • Page 6: Assembly

    ELECTRIC CHAIN SAW ASSEMBLY Note: Some models are pre assembled. As- sembly is not needed on these models. See Saw Chain Tension Adjustment, page 7. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly.
  • Page 7: Filling Oil Tank

    SAW CHAIN TENSION ADJUSTMENT WARNING: Unplug chain saw from power source before adjust- ing saw chain tension. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback.
  • Page 8: Operating Chain Saw

    ELECTRIC CHAIN SAW OPERATING CHAIN WARNING: Read and under- stand this owner’s manual be- fore operating this saw. Make certain you read and understand all Safety Warnings , pages 2 and 3. Improper use of this chain saw can cause severe injury or death from fire, electrical shock, or body contact with moving chain, or falling wood.
  • Page 9: Felling A Tree

    OPERATING CHAIN Continued FELLING A TREE (Cutting Down a Tree) WARNING: • Avoid kickback. Kickback can result in severe injury or death. See Kickback, page 3 to avoid risk of kickback. • Do not fell a tree without ample skill or expert help. •...
  • Page 10: Limbing A Tree

    ELECTRIC CHAIN SAW OPERATING CHAIN Continued LIMBING A TREE WARNING: Avoid kickback. Kickback can result in severe in- jury or death. See Kickback , page 3 to avoid risk of kickback. WARNING: When cutting limb that is under tension, use extreme caution.
  • Page 11: Trimming A Tree (Pruning)

    OPERATING CHAIN Continued Log Supported On Both Ends 1. Make first cut from above log (see Fig- ure 15). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut. 2. Make second cut on underside of log, directly under first cut.
  • Page 12: Cleaning And Maintenance

    ELECTRIC CHAIN SAW CLEANING AND MAINTENANCE NOTICE: Below are instructions for servicing your chain saw. Any servicing not mentioned below should be done by an authorized service center. CLEANING SAW BODY WARNING: Unplug chain saw from power source before servic- ing.
  • Page 13: Sharpening Saw Chain

    CLEANING AND MAINTENANCE Continued SHARPENING SAW CHAIN WARNING: Unplug chain saw from power source before servic- ing. Severe injury or death could occur from electrical shock or body contact with moving chain. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.
  • Page 14: Technical Service

    ELECTRIC CHAIN SAW CLEANING AND MAINTENANCE Continued Filing Cutter Depth Gauges The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpening, reset cutter depth gauges. 1. Place depth gauge tool (.025") firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 21).
  • Page 15: Troubleshooting

    TROUBLESHOOTING Note: For additional help, visit our technical service web site at www.desatech.com. OBSERVED FAULT Saw runs, but does not cut Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips Saw runs slow. Saw stalls easily Motor of saw does not run when you squeeze trigger Motor of saw runs, but chain does not move...
  • Page 16: Illustrated Parts Breakdown

    ® ELECTRIC CHAIN SAW ILLUSTRATED PARTS BREAKDOWN LNT-2 For more information, visit www.desatech.com 107990...
  • Page 17: Parts List

    This list contains replaceable parts used in your chainsaw. When ordering parts, be sure to provide the correct PARTS LIST model and serial numbers (from the model plate), then the part number and description of the desired part. LNT-2 PART...
  • Page 18 ® ELECTRIC CHAIN SAW ILLUSTRATED PARTS BREAKDOWN EL-7 For more information, visit www.desatech.com 107990...
  • Page 19 This list contains replaceable parts used in your chainsaw. When ordering parts, be sure to provide the correct PARTS LIST model and serial numbers (from the model plate), then the part number and description of the desired part. EL-7 PART NO.
  • Page 20: Authorized Service Centers

    ELECTRIC CHAIN SAW Ray’s Portable Heater Service Portable Heater Parts 3191 Myers Road 342 North County Road 400 East Camino, CA 95709-9550 Valparaiso, IN 46383-9704 530-644-7716 219-462-7441 1-800-362-6951 Baltimore Electric www.portableheaterparts.com 5 Manila Drive sales@portableheaterparts.com Hamden, CT 06514-0322 techservice@portableheaterparts.com 203-248-7553 1-800-397-7553 1349 Adams Street Eckley’s Small Engine...
  • Page 21 Nichols Ice & Oil KENTUCKY (KY) 2018 Park Road Gillum’s Service & Repair Connersville, IN 47331 8611 Rt. US 60 765-825-3741 Ashland, KY 41102 606-928-4932 B & W Repair Service 213 N. Main Street E-Z Rent It Inc. Dale, IN 47523 1428 U.S.
  • Page 22 ELECTRIC CHAIN SAW NORTH CAROLINA (NC) Leonard Hardware Leonard Electric Motor Repair, Inc. 145 North 15th Street 531 N. Fayetteville Street Sebring, OH 44672 Asheboro, NC 27203 330-938-6329 336-625-2375 Sparks Sales & Service Martin Equipment Company 5184 Fletcher Chapel Road 4209-B US 70 E.
  • Page 23: Replacement Parts And Accessories

    REPLACEMENT PARTS AND ACCESSORIES Purchase these accessories and parts from your nearest dealer or service center. If they can not supply these accessories or parts, either contact your nearest Parts Dealer or DESA Specialty Products™ for referral infor- mation. Parts dealers are listed in this manual. LNT-2 Part Number Description...
  • Page 24: Repair Service

    REPAIR SERVICE Note: Only use original replacement parts. This will protect your warranty coverage for parts replaced under warranty. Each authorized service center is indepen- dently owned and operated. For additional service center or warranty information, call 1-800-858-8501 or visit our technical ser- vice web site at www.desatech.com.

Table of Contents