Page 1
3898-93110 (711) OWNER / OPERATOR MANUAL POWER AUGER AG2300 (NOTE: Drill is optional part.) Thank you for purchasing a RedMax WARNING product. The engine exhaust from this product Before using our power auger, please contains chemicals known to the State...
Read this manual carefully to understand all safety precautions, controls, proper operation and maintenance of your RedMax power auger. Failure to do so could result in serious injury. Instructions contained in warnings within this manual marked with a concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
THINGS TO BE CAREFUL ABOUT WHEN USING YOUR POWER AUGER NOTES ON CARE AND MAINTENANCE OF YOUR POWER AUGER FUEL ... 9 HOW TO MIX FUEL FUELING THE UNIT OPERATION ... 10 INSTALLING DRILL THROTTLE CABLE ADJUSTMENT STARTING ENGINE STOPPING ENGINE DRILLING ADJUSTMENT OF IDLING SPEED MAINTENANCE ...
Safety Precautions ■ In order to ensure proper and safe operation of your power auger • Read this Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury.
Safety Precautions ■ Work gear and clothing • When using your power auger, always be sure to wear strong, durable, work clothing; shirts should be long-sleeved shirts and pants should be full-length pants reaching down to the ankles. • Always be sure to wear and helmet and face protector when using your power auger.
Safety Precautions ■ Things to check before using your power auger • Before beginning work, look around carefully to get a feel for the shape of the land, and whether or not there are any obstacles which might get in the way while working, and remove any obstacles which can be cleared away before beginning work.
Safety Precautions ■ Things to be careful about when using your power auger • When using your power auger, grip the handles of the power auger firmly with both hands, place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even...
• When replacing drills or any other parts or when replacing the oil or any lubricants, always be sure to use only RedMax products or products which have been certified by RedMax for use with the power auger.
3m(10ft) away from the fueling stop before starting the engine. • The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If RedMax oil is not available. Use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use.
■ Installing Drill 1. Slide the ring clip and remove the lock pin from the drill. 2. Put the drill onto the auger output shaft and insert the lock pin. Cover it with the ring clip. ■ Throttle Cable Adjustment Check the throttle cable play and adjust to .04 or .08 in.
Maintenance WARNING • Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug terminal to avoid accidental engine starts. ■ Daily Inspection • Remove grass or dust, from the entire body.
2 cycle oil into the cylinder. Crank the engine several times and replace the plug. Pull starter until compression is felt. • Brush off dirt from the drill surface and apply rust protective oil. • Store the machine in a dry, dust-free place.
Parts List NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3.
Page 16
Parts List : AG2300 Fig.1 AUGER DRIVE SHAFT GROUP 16 ...
Page 17
AG2300 Fig.1 AUGER DRIVE SHAFT GROUP Key# Part Number Description 3890-11101 CASE(A)COMP 3890-11112 • CASE(A) 3890-11140 • PIN 3890-11201 CASE(B)COMP 06030-06001 BEARING 06031-06001 BEARING 06030-06202 BEARING 06034-06202 BEARING 3127-13230 SPACER 04065-03515 RING 3890-12110 DRUM 04064-01210 RING 3890-13100 GEAR COMP 3890-13110 •...
Page 18
Parts List : AG2300 Fig.2 DRILL and ACCESSORY GROUP 18 ...