Download Print this page

RCA SPS3600 User Manual

Rca undercabinet radio with cd player user manual
Hide thumbs

Advertisement

Quick Links

V1.0 (EN)
User Manual
SPS3600
EN
It's important to read this instruction prior to using your new product for the
first time.

Important Safety Instructions

Some of the following information may not apply to your particular product;
however, as with any electronic product, precautions should be observed
during handling and use.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (Including amplifiers) that produce heat.
Do not defect the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your wall outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
Only use attachments / accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart /
apparatus combination to avoid injury from tip-over.
Portable Cart
Warning
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as the power
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

Mounting Instructions

TOOLS NEEDED:
1) Electric drill with 1/4" bit; 2) Phillips-head (cross style) Screwdriver.
STEP 1
If your cabinet does NOT have an overhang:
a) Place the Mounting Template in the desired location inside or underneath
the cabinet (whichever has less obstructions, and will be easier for you
to reach to drill holes), flush with the front edge of the cabinet and tape it
down. Go to STEP 2.
If your cabinet DOES have an overhang:
a) Measure the thickness of the cabinet overhang (see Figure 1).
Figure 1
b) Fold the Mounting Template along the guideline that is closest to the
thickness of your cabinet overhang.
c) Tape Mounting Template to the underside of the cabinet with the folded
portion of the Mounting Template flush up against the cabinet overhang
(see Figure 2). Go to STEP 2.
Figure 2

General Controls

Front Panel Controls
1. CD Drawer
10.
NEXT Button
2. Remote Control Sensor
Press to change the digits(in
3. LCD Display
Timer mode) / skip to the next
4.
POWER Button
track(in CD mode) / tune in to
Press to turn ON the unit or put
different stations(in Radio mode).
it in STANDBY(OFF) mode.
11. VOLUME+/- Button
5.
PLAY/PAUSE Button
Press to adjust the volume.
Press to start / pause playback
12. Display Button
13.
REPEAT/PRESET Button
of a disc.
6.
STOP Button
Press to repeat a single track or
Press to stop playing a disc.
an entire disc(in CD mode) / set
7.
CLOCK SET/MEMORY
a radio station preset (in Radio
Button
mode).
Press to set a clock(in standby
14. CD·RADIO·AUX Button
mode) / store a track in
15. AM/FM Band Button
memory (in CD stop mode).
16.
OPEN/CLOSE Button
8. TIMER Button
Press to open / close the CD
Press to set the cooking timer.
door.
9.
PREV Button
17. Dock for MP3 Player
Press to change the digits(in
Timer mode) / skip to the
previous track(in CD mode) /
tune in to different stations(in
Radio mode).

Safety Precautions

The symbol for Class II
(Double Insulation)
The lightning flash with an arrowhead symbol, within the
equilateral triangle, is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to cause an electric shock.
The exclamation point within the equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in this owner's manual.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING: THE APPARATUS SHALL NOT BE EXPOSED TO
DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, THEN FULLY INSERT.
IF YOUR PRODUCT
OPERATES ON BATTERIES, ahere to the
following precautions:
A. Any battery may leak electrolyte if mixed with a different battery
type, if inserted incorrectly, or if all batteries are not replaced at the
same time.
B. Any battery may leak electrolyte or explode if disposed of in fire or
an attempt is made to charge a battery not intended to be recharged.
C. Discard leaky batteries immediately. Leaking batteries can cause
skin burns or other personal injury. When discarding batteries, be
sure to dispose of them in the proper manner, according to provincial
and local regulations.
Important Battery Precautions
Any battery may may present a risk of fire, explosion, or chemical
burn if abused. Do not try to charge a battery that is not intended to
be recharged, do not incinerate, and do not puncture.
Non-rechargeable batteries, such as alkaline batteries, may leak if left
in your product for a long period of time. Remove the batteries from
the product if you are not going to use it for a month or more.
If your product uses more than one battery, do not mix types and
make sure they are inserted correctly. Mixing types or inserting
incorrectly may cause them to leak.
Discard any leaky or deformed battery immediately. They may cause
skin burns or other personal injury.
Batteries shall not be exposed to excessive heat such as sunshine,
fire or the like.
Please help to protect the environment by recycling or disposing of
batteries according to federal, state, and local regulations.
STEP 2
Use an electric drill with a ¼" bit (not included) to drill all four holes
marked on the Mounting Template (see Figure 3). To reduce splintering,
place a small piece of masking tape over each hole location before
drilling.
Go to STEP 3.
Figure 3
STEP 3
If your cabinet does NOT have an overhang:
a) Eight screws are included with this unit, but you will only need four of
them. Select the screw length which will go completely through your
cabinet bottom, and provide at least 3/8" of thread to screw into the
main unit.
b) Insert the four selected screws through each hole from the inside of
the cabinet going down (see Figure4).
Mounting
Screw
Figure 4
c) Hold the unit up against the bottom of the cabinet, and align the four
holes on the top of the unit with the screws. Partially tighten each
screw, but do not fully tighten the screws until all of them have been
started.
Bottom Cabinet Controls
18
19
20
21
22
18. Lens
19. Light ON/OFF Button
20. MP3 Player Docker
21. Aux Cable
22. Speakers
Safety Precautions
ON SAFETY
Before operating, make sure the voltage requirement of the mains plug
matches your local voltage.
Disconnect the mains plug immediately if liquid spills into or onto the
unit, or if an object falls into the unit. The unit should not be used until
service by a qualified service personnel is completed.
Do not open the cabinet. Lasers used in rays employed by the unit may
damage your eyes. Any servicing should be done by qualified service
personnel.
When you are not going to use the unit for a long period of time,
disconnect the mains plug.
ON PLACEMENT
Do not leave, mount or use the unit in places which are extremely hot,
cold, dusty, or humid.
Allow adequate air circulation to prevent internal heat build-up. Do
not place the unit on a surface or near materials (a curtain ex. rugs,
blankets, curtains, etc.) which might block the ventilation holes.
ON CONDENSATION
When left in a heated room where it is warm and damp, water droplets
or condensation may form inside the CD player. When there is
condensation inside the unit, the unit may not function normally. Let it
stand for 1 to 2 hours before turning the power on, or gradually heat the
room and allow the unit to dry before use.
Before You Begin
Useful Advice
Do not use your system immediately after transporting it from a cold
place to a warm place, as condensation may cause the system to
malfunction. If moisture forms inside this system, it may not operate
properly. To correct the problem, turn off the power and wait about 30
minutes for moisture to evaporate.
This system is fitted with a laser. To avoid accidents, it is to be opened
by qualified technicians only.
Never leave the tray open as dust could cover the laser lens and / or the
tray could be bumped into accidentally.
Do not palce the system near wet areas such as bathrooms and pool
inside. Avoid storing the system at humid places or near abnormally
heated areas.
Main plug is used as the disconnected device, it shall remain operable
and should not be obstructed during intended use. To be completely
disconnected the apparatus from supply mains, the main plug of
the apparatus shall be disconnected from the mains socket outlet
completely.
Ensure minimum distance around the apparatus for sufficient ventilation.
The ventilation should not be impeded by covering the ventilation
openings with items, suchventilation openings with items, such as
newspaper, etc.
No naked flame source, such as lighted candles, should be placed on
the apparatus.
d) Gently tighten each screw until they are firmly holding the unit in place.
Go to STEP 4.
If your cabinet DOES have an overhang:
a) Eight screws are included with this unit, but you will only need four of
them. Select the screw length which will go completely through your
cabinet bottom, and extend at least will go completely through your
cabinet bottom, and extend at least 3/8" past the bottom of your cabinet
overhang.
b) This unit includes three sets of four spacers of various lengths. The
spacers can be put together to form longer spacers to accommodate
various cabinet overhang thicknesses. Determine the best combination
of spacers which is equal to or longer than the cabinet overhang
thickness.
c) Insert the four selected screws through each hole from the inside of the
cabinet going down (see Figure 5).
Mounting
Screw
Figure 5
Spacer
(Optional)
d)
Hold each screw head down and push the unit and spacers onto the
screws, then hold the unit up until spacers are firmly against the bottom
of the cabinet (and fully nested within each other if you are using
multiple spacers for each screw).
e) Partially tighten each screw, but do not fully tighten the screws until all of
them have been started (see Figure 6).
f) Gently tighten each screw until they are firmly holding the unit in place.
The top front edge of the unit should clear the overhang.
Go to STEP 4.
Remote Control
1.
POWER Button
2.
CLOCK SET/MEMORY Button
3.
REPEAT/PRESET Button
4. VOLUME+/- Button
5. Display Button
6. FUNCTION button
7. TUNING /
/
Button
8.
STOP / BAND Button
9.
PLAY/PAUSE Button
USING THE REMOTE CONTROL CORRECTLY
• Point the remote control at the REMOTE SENSOR located on the unit.
• When there is a strong ambient light source, the performance of the
remote's infrared may be degraded, causing unreliable operation.
• The recommended effective distance for remote operation is about 13 feet
(4 m).
Notes:
• When tuning the radio or searching for a track, the
MEMORY buttons on the remote control are the same as the
/ MEMORY buttons on the main unit.
• The
REPEAT/PRESET button on the remote control is the
same as the REPEAT/PRESET button on the main unit.
FCC information
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user's authority to
operate the equipment.
For your safety
The AC power plug is polarized (one blade is wider than the
other) and only fits into AC power outlets one way. If the plug
won't go into the outlet completely, turn the plug over and try
to insert it the other way. If it still won't fit, contact a qualified
electrician to change the outlet, or use a different one. Do not
attempt to bypass this safety feature.
Removing the power supply is the only way to completely remove power
from your product. Make sure the power plug remains easily accessible.

Service Information

For your records
In the event that service should be required, you may need the model
number. In the space below, record the date and place of purchase:
Model No.
Date of Purchase
Place of Purchase
Service information
This product should be serviced only by those specially trained in
appropriate servicing techniques. For instructions on how to obtain service,
refer to the warranty included in this Guide.

Technical Information

Technical information
Product: KITCHEN RADIO WITH CD PLAYER
Band: RCA
Model: SPS3600
Power Supply: 120V ~ 60Hz
STEP 4
Plug the cord into the wall outlet
a) Before connecting power cord, make sure the voltage of the unit matches
with your local voltage.
b) Plug the power cord directly into the nearest wall outlet, and wrap the
remaining cord around the cord storage knob at the rear of the unit.
MOUNTING SUGGESTIONS
1) If your cabinet has obstructions inside it which prevent you from using
the template, cut out the corresponding area on the template, but do
NOT cut out or through the screw holes.
2) If your cabinet has obstructions underneath it, which will interfere with
the mounting of the unit, remove the obstruction before mounting the
unit, or find another location to mount the unit.
3) It is recommended that you wear safety glasses while drilling to prevent
eye injuries.
4) For wood cabinets, you may want to mark the hole locations with a nail,
pressed gently but firmly into the wood so that a slight impression is
made. This will also help keep the drill bit centered in the right location.
5) Hold the drill firmly against the cabinet to keep the drill from "walking".
CAUTION
TO REDUCE THE RISK OF FIRE, DO NOT PLACE ANY HEATING
OR COOKING APPARATUS BENEATH THIS UNIT.
ATTENTION
• Remove the protective plastic tab before operating the remote control.
• To change battery
1. Open the battery door.
2. Insert one CR2025 (3V) size battery.
BATTERY REPLACEMENT
When the battery becomes weak, the operating distance of the remote
/
control is greatly reduced and you will need to replace it.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
Note:Dispose of used batteries in accordance with local laws and
regulations.
WARNING: NEVER DISPOSE OF BATTERY IN FIRE OR IT MAY
EXPLODE.
Figure 6

Advertisement

loading

  Related Manuals for RCA SPS3600

  Summary of Contents for RCA SPS3600

  • Page 1: Safety Precautions

    Technical Information Technical information Product: KITCHEN RADIO WITH CD PLAYER Band: RCA Model: SPS3600 Power Supply: 120V ~ 60Hz STEP 4 Plug the cord into the wall outlet a) Before connecting power cord, make sure the voltage of the unit matches with your local voltage.
  • Page 2: Display Function

    Center for one year from the defective warranty date. Such replacement 1-877-252-6873 or www.1800customersupport.com/RCA. parts or products are warranted for an additional one year from the date of repair or replacement. The Customer will be required to ship the unit to...