Download Print this page

RCA PRO LX5 II User Manual

Two-way die-cast speaker with dipole tweeter.
Hide thumbs
   

Advertisement

40-5007.fm Page 1 Monday, September 20, 1999 12:00 PM
T T T T w w w w o o o o - - - - W W W W ay
ay D D D D i i i i e e e e - - - - C C C C a a a a s s s s t t t t S S S S p p p p eake
ay
ay
Your PRO LX5 II Two-Way Die-Cast
Speaker with DiPole Tweeter is small in
size, but not in sound! Its 5-inch
polypropylene woofer accurately tracks
signals to provide outstanding bass, while
the wide-angle dipole tweeter produces
crisp, detailed highs with 360 dispersion.
Your speaker's acoustic design matches
the woofer and tweeter with the enclosure
and damping materials to provide
amazingly smooth and broad frequency
response.
Your can handle up to 130 watts of
power. The speaker is magnetically
shielded, so you can safely place it next to
your television or monitor.
U U U U N N N N P P P P A A A A C C C C K K K K I I I I NG
NG
NG
NG
Your PRO LX5 II is shipped in protective
packing materials. Before you use the
speaker, follow these steps to unpack it.
Caution: To avoid
damaging the speaker's
tweeter, do not touch the
tweeter's film while you
are unpacking the speaker.
1. Remove the corrugated board and the
plastic foam packing box.
2. Remove the plastic cover from the
tweeter.
eaker r r r w w w w i i i i t t t t h h h h D D D D i i i i P P P P o o o o l l l l e e e e T T T T w w w w ee
eake
eake
3. Carefully place the top grille on the
speaker, making sure not to touch the
tweeter' s plastic film with the cover.
Top
Grille
Front
Grille
1999 Tandy Corporation.
©
All Rights Reserved.
eet t t t e e e e r r r r
ee
ee
Corrugated
Board
Plastic Foam
Packing
Box (Top)
Plastic
Cover
Tweeter
Tweeter
Film

Advertisement

   Related Manuals for RCA PRO LX5 II

   Summary of Contents for RCA PRO LX5 II

  • Page 1

    U U U U N N N N P P P P A A A A C C C C K K K K I I I I NG Your PRO LX5 II is shipped in protective packing materials. Before you use the speaker, follow these steps to unpack it.

  • Page 2

    (or some other acoustically hard surface) greatly reinforces the speaker’s sound quality. If possible, place the front edge of the speaker flush with the front edge of the shelf. For the best sound, avoid floor locations; floor coverings can absorb much of the sound.

  • Page 3

    With the speaker placed at the desired location, measure the distance from the speaker to the amplifier. Use 18-gauge speaker wire for a distance of 50 feet or less. For a distance greater than 50 feet, use heavier 16-gauge wire.

  • Page 4

    This speaker has been manufactured to the specifications of RadioShack and is covered by a limited warranty from RadioShack. If your speaker is not operating as it should, take it to your local RadioShack store or call 1-800-THE-SHACK for assistance.

  • Page 5

    Power Handling ... 65 Watts (RMS) Maximum Power ... 130 Watts Impedance ... 8 Ohms (Nominal) Speaker Complement ... 5-Inch High-Compliance Woofer Dimensions (HWD) w/Front Grille ... 10 Weight ... 8 lb 6 oz Specifications are typical; individual units might vary. Specifications are subject to change and improvement without notice.

  • Page 6

    40-5007.fm Page 6 Monday, September 20, 1999 12:00 PM N N N N O O O O T T T T E E E E S S S S...

  • Page 7

    40-5007.fm Page 7 Monday, September 20, 1999 12:00 PM...

  • Page 8

    40-5007.fm Page 8 Monday, September 20, 1999 12:00 PM Limited Ninety-Day Warranty This product is warranted by RadioShack against manufacturing defects in material and workman- ship under normal use for ninety (90) days from the date of purchase from RadioShack company- owned stores and authorized RadioShack franchisees and dealers.

Comments to this Manuals

Symbols: 0
Latest comments: